Deutsch dropdown-ico

Bedienungsanleitung Bushnell 98-2293/05-12

28 Seiten 4.4 mb
Download

Zur Seite of 28

Summary
  • Bushnell 98-2293/05-12 - page 1

    PROUD USA COMP ANY Lit #: 98-2293/05-12 This manual should only be used for Elite T actical Riflescopes with these reticle designs: Bushnell Mil Dot Reticle Bushnell G2DMR Reticle Horus Vision H59 Reticle Horus Vision TRMR2 Reticle ...

  • Bushnell 98-2293/05-12 - page 2

    2 Fast Focus Eyepiece Power Change Ring Side Focus Adjustment Elevation T urret Windage T urret Sunshade ...

  • Bushnell 98-2293/05-12 - page 3

    3 ELEV A TION AND WIND AGE TURRETS The turrets of the Bushnell ® Elite ® T actical Riflescope provide audible and visual references. Each turn of the turret provides an audible “click” which coincides with a movement of the visible reference point on the turret knob. Additionally , clicks can be felt by your fingers as the turret knob moves ...

  • Bushnell 98-2293/05-12 - page 4

    4 F AST FOCUS EYEPIECE The fast-focus eyepiece dial is found on the ocular end of the Bushnell Elite T actical Riflescope. Use this adjustment to obtain a reticle image that appears sharp to your eyes. If adjustment is needed, look at a distant object for several seconds without using your scope. Then, shift your vision quickly , looking through t ...

  • Bushnell 98-2293/05-12 - page 5

    5 FIRST FOCAL PLANE RETICLE The Bushnell Elite T actical Riflescopes covered by this manual have their reticles located in the first focal plane. Therefore, the reticle will increase in size when the magnification is increased. This feature allows the continued use of the mil measurement system contained in the reticle, regardless of the power s ...

  • Bushnell 98-2293/05-12 - page 6

    6 In the example to the left using the H59 reticle, the shooter was attempting to hit a target in the center of the crosshairs. The actual point of impact hit 4 Mils down and 3 Mils left indicated by the red dot. Adjust the elevation dial 4 Mils up/windage dial 3 Mils right. Another way to look at this is to determine what adjustment needs to be do ...

  • Bushnell 98-2293/05-12 - page 7

    7 BUSHNELL MIL DOT RETICLE The Bushnell Mil Dot Reticle provides a total of ten Mils on both the vertical and horizontal crosshairs. One Mil is measured from the middle of one dot to the middle of the next dot. The last Mil on the outer edges portion of the horizontal and vertical crosshair is measured from the center of the fourth Mil Dot from cen ...

  • Bushnell 98-2293/05-12 - page 8

    8 The Mil Dot Reticle Measurement System in the F irst Focal Plane Applies at any Ma gnification Level. 2 Mils at 12x (100 yards) 2 Mils at 3.5x (100 yards) ...

  • Bushnell 98-2293/05-12 - page 9

    9 USING THE MIL DOT RETICLE FOR RANGING The Equations: Size of target in yards X 1000 = Range in Y ards Size of T arget in Mils Size of target in inches X 27.778 = Range in Y ards Size of target in Mils Size of target in inches X 25.4 = Range in Meters Size of target in Mils Example 1: Looking through the riflescope, I located a preset target tha ...

  • Bushnell 98-2293/05-12 - page 10

    10 Example 2: T ake the same size target but now the Mil reading is .75 (from crosshair intersection to bottom of first Mil Dot). Known size of target: 12”x 12” Mil Reading: .75 Mil 12 X 27.778 .75 Mil CONVERTING TRAJECTOR Y DA T A TO MIL HOLDOVERS T o calculate holdovers you must first obtain your round’ s trajectory data. Look at the ammu ...

  • Bushnell 98-2293/05-12 - page 11

    11 = Holdover T rajectory Mil Size at given Distance FEDERAL .308 168-GR BTHP HOLDOVERS FOR A MIL-DOT RETICLE Distance T rajectory 1 Mil Size Actual Holdover 100 Y ards 0 0 Mils 0 Mils 200 Y ards 4.5” 7.2 Mils .62 Mils 300 Y ards 15.9” 10.8 Mils 1.47 Mils 400 Y ards 35.5” 14.4 Mils 2.46 Mils 500 Y ards 64.6” 18.0 Mils 3.58 Mils ...

  • Bushnell 98-2293/05-12 - page 12

    12 USING THE MIL DOT RETICLE FOR HOLDOVER Once you know how to range your target with the Mil Dot reticle, and using the previous example, you can use the reticle instead of the turrets to make adjustments with holdover . For example, your range tells you that the 12” target is 300 yards away , (12”*27.778) / (1.1Mil). Based on the Federal .308 ...

  • Bushnell 98-2293/05-12 - page 13

    13 BUSHNELL G2DMR ™ RETICLE The G2DMR reticle, developed in conjunction with G.A. Precision , provides a c lean reticle space while giving you the ability to range targets with extreme accuracy using .1 Mil reference points. The extended horizontal mil markings on the lower portion of the vertical crosshair can be used for both ranging and windag ...

  • Bushnell 98-2293/05-12 - page 14

    14 THE HORIZONT AL CROSSHAIR On the horizontal crosshair , numerically designated Mil markings extend from the center of the crosshairs outward to the right in 2 Mil increments. T o keep the retic le plane clean, the numbers were removed on the left side of the reticle but the reference points coincide with the markings from the right side of the c ...

  • Bushnell 98-2293/05-12 - page 15

    15 Extending past the 8 Mil mark, the numerals stop. 1 Mil increments are then designated by the longer hash marks which measure 1.5 Mil in height from top to bottom. T en .1 Mil markings are visible between each 1 Mil marking, continuing out to 13 Mils from center . The height from top to bottom of the .1 Mil markings is 1 Mil. The .1 Mil markings ...

  • Bushnell 98-2293/05-12 - page 16

    16 THE VERTIC AL CROSSHAIR Similar to the horizontal crosshair , the vertical crosshair places the numerically designated Mil markings on only one side. Once again, the numerically designated markings are found in 2 Mil increments with hash marks every .5 Mil. Note the vertical cross hair extends to provide numerically designated markings up to 10 ...

  • Bushnell 98-2293/05-12 - page 17

    17 HORUS VISION H59 RETICLE The H59 reticle is a “field-tuned” version of the H58 retic le from Horus Vision. The horizontal grid is widened by one mil for increased wind holdover . Additionally , the center cross has been turned into a “broken cross” so groupings are less obscured and more easily seen. The H59 reticle is free of the c lut ...

  • Bushnell 98-2293/05-12 - page 18

    18 This process works well for many cartridges and weapon systems,but not all will impact exactly the same. However this system should place you close enough to make a solid hit, all else being equal. If shooting with a different caliber or muzzle velocity , you may need to add to or subtract from the original elevation hold to adapt the formula fo ...

  • Bushnell 98-2293/05-12 - page 19

    19 HORUS VISION TRMR2 RETICLE The TRMR2 is a refined-mil reticle. Precision mil-marking c lusters interspersed throughout the reticle enable fast accurate measurements at .1, .2, .5 and 1 mil increments. With the 12” ranging brackets located on the lower portion of the vertical stadia, there is no need to make an additional adjustment once the c ...

  • Bushnell 98-2293/05-12 - page 20

    20 This process works well for many cartridges and weapon systems, but not all will impact exactly the same. However , this system should place you close enough to make a solid hit, all else being equal. If shooting with a different caliber or muzzle velocity (BC’ s), you may need to add to or subtract from the original elevation hold to adapt th ...

  • Bushnell 98-2293/05-12 - page 21

    21 CALCULA TING HOLDS FOR MOVING T ARGETS The TRMR2 reticle has 14 wind dots left to right. 7 wind dots to the left and 7 wind dots to the right of center . Each dot accounts for 3,4, or 5 mph of wind depending on the Ballistic Coefficient you are using. Ballistic Coefficient Wind Dot Value .3 5 mph .4 4 mph .5 3mph For example, if you were holdi ...

  • Bushnell 98-2293/05-12 - page 22

    22 RETICLE FROM 10TH MIL TO 38TH MIL DOWN ON VERTIC AL ST ADIA The standard Horus grid is found from the 10th Mil down on the vertical stadia to a total of 38 Mils. The Horus grid evolves reticles beyond outdated crosshairs and mil dots. The patented grid eliminates the need to adjust windage or elevation knobs. As a result you find your target fa ...

  • Bushnell 98-2293/05-12 - page 23

    23 MAINTENANCE Y our Bushnell Elite T actical HDMR riflescope, though amazingly tough, is a precision instrument that deserves reasonably cautious care. 1. When cleaning the lenses, first blow a way any dry dirt and dust, or use a soft lens brush. Fingerprints and lubricants can be wiped off with lens tissue, or a soft clean cloth, moistened with ...

  • Bushnell 98-2293/05-12 - page 24

    24 WARRANTY / REP AIR ELITE ® LIFETIME LIMITED WARRANTY We are so proud of our Bushnell ® ELITE ® T actical HDMR ™ Riflescopes that their materials and workmanship are warranted to be free of defects for the life of the ELITE T actical HDMR Riflescope. The warranty is available to any owner of the ELITE T actical HDMR Riflescope. No receipt ...

  • Bushnell 98-2293/05-12 - page 25

    25 IN U.S.A. Send T o: IN CANADA Send T o: Bushnell Outdoor Products Bushnell Outdoor Products Attn.: Repairs Attn.: Repairs 9200 Cody 25A East Pearce Street, Unit 1 Overland Park, Kansas 66214 Richmond Hill, Ontario L4B 2M9 For products purchased outside the United States or Canada please contact your local dealer for applicable warranty informati ...

  • Bushnell 98-2293/05-12 - page 26

    26 ...

  • Bushnell 98-2293/05-12 - page 27

    27 ...

  • Bushnell 98-2293/05-12 - page 28

    For further questions or additional information please contact: Bushnell Outdoor Products 9200 Cody , Overland Park, Kansas 66214 (800) 423-3537 www .bushnell.com ©2012 Bushnell Outdoor Products ...

Produzent Bushnell Kategorie Hunting Equipment

Dokumente, die wir vom Produzenten des Geräts Bushnell 98-2293/05-12 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Bushnell
- Bedienungsanleitungen 98-2293/05-12
- Produktkarten Bushnell
- Informationsbroschüren
- oder Energieetiketten Bushnell 98-2293/05-12
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Bushnell 98-2293/05-12.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Bushnell 98-2293/05-12, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Bushnell 98-2293/05-12. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Bushnell 98-2293/05-12 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Bushnell 98-2293/05-12, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Bushnell 98-2293/05-12 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Bushnell 98-2293/05-12 verständlich ist.

Eine gänzliche Bedienungsanleitung von Bushnell sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Bushnell 98-2293/05-12 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Bushnell 98-2293/05-12 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Bushnell 98-2293/05-12, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Bushnell 98-2293/05-12 - die uns die ersten Schritte während der Nutzung von Bushnell 98-2293/05-12 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Bushnell 98-2293/05-12 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Bushnell 98-2293/05-12 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Bushnell 98-2293/05-12?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Bushnell 98-2293/05-12 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Bushnell 98-2293/05-12 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)