Deutsch dropdown-ico

Bedienungsanleitung Brother MFC-8640D

175 Seiten 1.82 mb
Download

Zur Seite of 175

Summary
  • Brother MFC-8640D - page 1

    Multi-Protocol Print/Fax Server Network User’s Guide NC-9100h MFC-8440 MFC-8640D MFC-8840D MFC-8840DN DCP-8040 DCP-8045D Please read this manual thoroughly before using the machine. You can print or view this manual from the CD-ROM at any time, please keep the CD-ROM in a convenient place for quick and easy reference at all times. The Brother Sol ...

  • Brother MFC-8640D - page 2

    i Trademarks Brother is a regi st ere d tr ad e ma r k of Brother Industries, Ltd. HP, HP/UX, JetDirect and JetAdmin are trademarks of Hewlett-Packard Company. UNIX is a trademarks of UNIX Systems Laboratories. Ethernet is trademark of Xerox Corp oration. Postscript is trademark of Adobe Systems Incorporated. Netware is a trademark of Novell, Inc. ...

  • Brother MFC-8640D - page 3

    ii IMPORTANT NOTE: For technical and operational assistance , you must call. Calls must be made from within that country. In USA 1-800-276-7746 In Canada 1-877-BROTHER In Europe Visit http://www.b rother.com for contact information on your local Brother office. If you have any comments or suggestions, please write to us at: In Europe European Techn ...

  • Brother MFC-8640D - page 4

    iii Introduction Overview The Brother NC-9100h Print / Fax Serve r allows your Brother machine to be attached and shared on a 10/100Mbit Etherne t Network. Web Based Management and Administratio n utilities provide easy configuration and management of your Brother machine. Once installed and config ured, the NC-9100h allo ws your machine to FAX doc ...

  • Brother MFC-8640D - page 5

    iv IMPORTANT INFORMATION: REGULATIONS Federal Communications Commi ssion (FCC) Declaration of Conformity (For U.S.A. only) Responsible Party: Brother Internat ion al Corporation 100 Somerset Corp or a te Bo ule va rd Bridgewater, NJ 08807-091 1, USA TEL: (90 8) 704-1700 declares, that the prod ucts Product Name: Brother Netw ork Card (BR-n et) Mode ...

  • Brother MFC-8640D - page 6

    v Declaration of Co nformity (Europe) We, Brother Ind ustries, Ltd., 15-1, Naeshiro-c ho, Mizuho-ku, Nagoya 467-8561, Japan declare that this p roduct is in conformity with th e following normative documents. Safety: EN 60950, EMC: EN 55022 Class B, EN 55024 following the provisions of t he Low Voltage Directive 73 /23/EEC and the Electromagnetic C ...

  • Brother MFC-8640D - page 7

    vi Table of Contents Introduction ....... ................. ................ ................ ............ iii Overview .... ................ ................. ................ ............... iii Features .... ................ ................. ................ ............... iii IMPORTANT INFORM ATION: REGULATI ONS...... ..... iv Federal Commun ...

  • Brother MFC-8640D - page 8

    vii Windows NT ® 4.0 Printing Associating to the Printe r ........... ... ... ... .... ................ ... . 2-6 Windows NT ® 4.0 Printing Adding a Secon d Brother LPR P ort .............. .............. 2-7 Other Sourc es of Inform ation ....... ................ .............. 2-7 3 Peer to Peer Print ing . ................ ................... ...

  • Brother MFC-8640D - page 9

    viii Brother Internet Print: Using BRAdmin Profession al utility to Co nfigure the Prin t Server ....... ................ ...... 5-4 Brother Inter net Print: Using a We b Browser to Configure the Print Server ................. ................... ...... 5-5 Brother Internet Print: In stalling the BIP software on Windows ® 95/98/Me/2000/XP and Wind ...

  • Brother MFC-8640D - page 10

    ix How to Select the Print Server (AppleTalk/EtherTalk ) ................ ................ ................. 7-8 How to Select the Print Server (TCP/IP) ...... .............. 7-9 Changing the Configura tion ............. ................ ......... 7-10 Other Sourc es of Inform ation ....... ................ ............ 7-10 Printing from a Ma cint ...

  • Brother MFC-8640D - page 11

    x Poll Frequency ..................... ... .... ... ................ ..... 10-13 Header ....................... ................. ................ ........ 10-13 Del Error Mail .... ... ... ... .... ... ... ................ ... ............ 10-14 Notification ..................... ................ ................ ..... 10-14 Setup Mail TX (Fo r MF ...

  • Brother MFC-8640D - page 12

    xi 12 Internet FAX (MFC Only) .................. ................... ............... 12-1 Overview ................ ................. ................ ................ .. 12-1 Getting Conn ected ................ ................ ............... 12-2 Front Pane l Key Functions ....... ................ ............ 12-2 Sending an Inter n et Fax .... ...

  • Brother MFC-8640D - page 13

    xii 14 Brother Internet Fax Printing Softwa re ............ ................ . 14-1 Overview ............... ................ ................ ............. ....... 14-1 Installing Brother In ternet Fax Printing Driver ........... 14-2 Changing the BFP Port Settings ........... ................ .... 14-4 Relay Broadcast Funct i on .. ... ... ... .. ...

  • Brother MFC-8640D - page 14

    UNIX PRINTING 1 - 1 1 1 Unix Printing Printing from Unix/Linux Using TCP/IP Overview Brother Print/Fax servers are supp lied with the Transmission Control Protocol/Internet Protocol (TCP/IP) prot ocol suite. Since virtually all UNIX host computers support TCP/IP, this capability allows a printer to be shared on a UNIX Ethernet network. As with all ...

  • Brother MFC-8640D - page 15

    1 - 2 UNIX PRINTING 5 When configuring the PRINT CAP file, pay particular attention to the service names, BINARY_P1 and TEXT_P1. TCP/IP Brother Print/Fax servers appear to the ne twork as a UNIX host computer with a unique IP address running the lpd (line printer daemon) protocol. As a re sult, any host computer that supports the Berkeley remote LP ...

  • Brother MFC-8640D - page 16

    UNIX PRINTING 1 - 3 The actual format of the entry may vary depending on your system, check your system docum entation and also note the format of other entries in the /etc/hosts file. In any case, the node name in the /etc/hos ts file must match the node name in the /etc/printcap file. Some systems such as HP-UX and AIX allow you to enter the I P ...

  • Brother MFC-8640D - page 17

    1 - 4 UNIX PRINTING 3 Configure the /etc/printcap file on each host computer to specify the local print queue, the Print/Fax ser ver name (also called remote machine or rm), and the Print/Fax server service name (also called remote printer, remote queue, or rp), and the spool directory. An example of a typical printcap file: laser1|Printer on Floor ...

  • Brother MFC-8640D - page 18

    UNIX PRINTING 1 - 5 %lpc status laser1: queuing is enabled printing is enabled no entries no daemon present Users of AT&T-compatible UNIX systems can generally use the lpstat or rlpstat commands to obtain simila r status information. Because this procedure varies from system to system, refer to your system documentation for th e exact usage. 4 ...

  • Brother MFC-8640D - page 19

    1 - 6 UNIX PRINTING Linux Configuration If you do not wish to use the comman d line interface to configure your Linux distribution, you may wish to use the Linux Printer System Manager application on your GUI. To do this, do th e following: 1 From the Linux Printer System Manager screen , click the Add button. 2 You will now be asked to spec ify wh ...

  • Brother MFC-8640D - page 20

    UNIX PRINTING 1 - 7 HP-UX Configuration In the case of HP-UX10.xx, the sam program is used to set up the remote printer. The steps are as follows: 1 Execute the sam program. From the list of options, select Printers and Plotters . 2 Select LP Spooler . 3 Select Printers and Plotters . 4 Select Actions and then Add Remote Printer/Plotter . 5 Enter a ...

  • Brother MFC-8640D - page 21

    1 - 8 UNIX PRINTING Earlier versions of HP-UX use si milar procedures to 10.xx users: 1 Enter sam and select Peripheral Device s and then Add Remote Printer (not Networked printer) . 2 Enter the following remote printer settings (the othe r settings do not matter): ■ Line printer name (user-selectable). ■ Remote system name (the Print/Fax serve ...

  • Brother MFC-8640D - page 22

    UNIX PRINTING 1 - 9 The procedure for pre-V4.0 systems is a s follows. 1 Enter smit and select devices . 2 Select printer/plotter . 3 Select manage remote printer s ubsystem . 4 Select client services . 5 Select remote printer queues . 6 Select add a remote queue . 7 Enter the following remote queue settings: ■ Name of queue to add (user selectab ...

  • Brother MFC-8640D - page 23

    1 - 10 UNIX PRINTING If this is the first printer configured, you must also use the lpsched command prior to the accept command. As an alternative, you may use Printer Mana ger in the Admintool utility under OpenWindows. Select Edit , Add , and Add Access to Remote Printer . Then enter the Print/Fax server name in the format prnservername!prnserve ...

  • Brother MFC-8640D - page 24

    UNIX PRINTING 1 - 11 SCO UNIX requires TCP/IP V1.2 or later to work with Brother print servers. You must first configure the /etc/hosts and /etc/printcap files as described in step 2 . Then run the sysadmsh program as follows: 1 Select Printers . 2 Select Configure . 3 Select Add . 4 Enter the name of the print q ueue you entered in the /etc/printc ...

  • Brother MFC-8640D - page 25

    1 - 12 UNIX PRINTING Use the following one-line OS/4 00 command to create the LPD queue: CRTOUTQ OUTQ(<queuename> RMSTSYS (*INTNETADR) RMTPRTQ(<service>) AUTOSTRWTR(1) CNNTYPE(*IP) DESTT YPE (*OTHER) MFRTYPMDL (<driver>) INTNETADR('<ipaddress>') TEXT ('<description>') where <queuename> is the ...

  • Brother MFC-8640D - page 26

    UNIX PRINTING 1 - 13 If you have not created a sp ool directory for the Brother Print /Fax server on your UNIX host computer, you will need t o do so now (the printer setup utilities in HP/UX, AIX, Solaris 2.xx, a nd other systems will automatically create the spool directory). The lpd spool directory is usually located in the /usr/spool dire ctory ...

  • Brother MFC-8640D - page 27

    2 - 1 TCP/IP PRINTING 2 2 TCP/IP Printing Printing from Windows NT ® 4.0, Windows ® 2000/XP, LAN Server and Warp Server Overview Users of Windows NT ® 4.0 can print directly to a network-ready Brother machine using the TCP/IP protocol. Microsoft Windows NT ® 4.0 users must install Microsoft’s “TCP/IP Printing“ protocol. Windows ® 2000/XP ...

  • Brother MFC-8640D - page 28

    TCP/IP PRINTING 2 - 2 5 Windows ® 95/98/Me users can send pr int jobs using the IPP protocol via a Windo ws ® 2000/XP computer provided that t he Microsoft Internet Print Services software is installed on the client PC, Internet Information Server (IIS) is installed and running on the Windows ® 2000/XP co mputer and that the client PC is using v ...

  • Brother MFC-8640D - page 29

    2 - 3 TCP/IP PRINTING 3 Click on Next . 4 You must now select the correct Network printing port. Sele ct Create a new port and select Standard TCP/IP Port port from the pull-down window. 5 When you have done that click Next . 6 The Add Standard TCP/IP Port Wizard will now appear. Click the Next button. 7 Enter the IP address, or name of the printer ...

  • Brother MFC-8640D - page 30

    TCP/IP PRINTING 2 - 4 Windows ® 2000/XP Printing (Printer Driver already installed) If you have alre ady installed the prin ter driver and wish to configure it for network printing, follow these steps: 1 Select the printer driver you wish to configure. 2 Select File and then choose Properties . 3 Click the Ports tab of the driver and click Add Por ...

  • Brother MFC-8640D - page 31

    2 - 5 TCP/IP PRINTING 6 Configure the host IP address, subnet mask, and gateway address in that dialog. Consult your system manager for t hese addresses. 7 Click OK to exit (your Windows NT ® 4.0 or server will need to be re-booted). Windows NT ® 4.0 Printing Installing the Brother Pe er to Peer Software 1 Start the CD-ROM installation menu progr ...

  • Brother MFC-8640D - page 32

    TCP/IP PRINTING 2 - 6 Windows NT ® 4.0 Printing Associating to the Printer You must now create a printer on your Windows ® system u sing the standard Windows ® printer setup pro cedure. 1 To do this, go to the Start button, select Settings and then Printers . 2 Double click the Add Printer icon to get th e Add Printer Wizard . 3 Select My Comput ...

  • Brother MFC-8640D - page 33

    2 - 7 TCP/IP PRINTING Windows NT ® 4.0 Printing Adding a Second Brother LPR Port You do not need to re-run the install pro gram to add a new Brother LPR port. Instead, press the Sta rt button, select Settings , and open the Printers window. Click on the icon of the printer that you wish to configure, select File from the menu bar, and then choose ...

  • Brother MFC-8640D - page 34

    PEER TO PEER PRINTING 3 - 1 3 3 Peer to Peer Printing How to Print in a Windows ® 95/98/Me Peer to Peer network Overview Microsoft's Windows ® 95/98/Me operating systems feature built-in networking capabilities. These capabilities allow a Windo ws ® PC to be configured as a client wo rkstation in a file server ba sed network environment. Fo ...

  • Brother MFC-8640D - page 35

    3 - 2 PEER TO PEER PRINTING Driver Deployment Wizard This installer include s the Windows ® PCL d river and Brother network port driver (LPR and NetBIOS). If the administrator the n installs the printer driver and port driver using this software, he can save the file to the File server or send the file in E-mail to users. Then, each user just clic ...

  • Brother MFC-8640D - page 36

    PEER TO PEER PRINTING 3 - 3 5 Select the desired directory to install the Brother Peer to Pee r Print (LPR) files and push Next . The installation program will create the directory for you if it does not already exist on your disk. 6 Enter the Port name that you wish to use and click OK . The default port name is BLP1. Whichever name you choose, it ...

  • Brother MFC-8640D - page 37

    3 - 4 PEER TO PEER PRINTING 4 Select Local Printer when you are asked how the printers are connected to your computer, and t hen push Next . 5 Select the correct driver. Click Nex t when you are done. 6 If you have selected a printer driver that is already being used, you have the option of either kee ping the existing driver (recommended) or repla ...

  • Brother MFC-8640D - page 38

    PEER TO PEER PRINTING 3 - 5 Adding a Second Brother LPR Port You do not re-run the install progra m to add a new Brother LPR port. Instead, press the Start button, select Settings , and open the Printers window. Click on the icon of the printer that you wish to configure, select File from the menu bar, and then choose Properties . Click on the Deta ...

  • Brother MFC-8640D - page 39

    4 - 1 NETBIOS PEER TO PEER PRINTING 4 4 NetBIOS Peer to Peer Printing How to Print Using NetBIOS in Windows ® 95/98/Me/2000/XP, Windows NT ® 4.0, LAN Server and OS/2 Warp Server Overview Brother Print/Fax server range supports SMB (Server Message Block) over the TCP/IP protocol via the NetBI OS interface. This means that just like regular Windows ...

  • Brother MFC-8640D - page 40

    NETBIOS PEER TO PEER PRINTING 4 - 2 Print Server Configuration In order for this function to work, you must co rrectly change the DOMAIN name or WORKGROUP name to match that of your network. Once this is done, the Print/Fax server will appear automatically in your network neighborhood and you will b e able to send print documents to it without havi ...

  • Brother MFC-8640D - page 41

    4 - 3 NETBIOS PEER TO PEER PRINTING Changing the workgroup/domain name using a web browser You can change the wo rkgroup/domain name using BRAdmin Professional utility. To do this press NetBIOS tab and then ent er your workgroup/domain name into the Domain Na me text box. You can also use a standard WWW browser to change the NetBIOS name. To do thi ...

  • Brother MFC-8640D - page 42

    NETBIOS PEER TO PEER PRINTING 4 - 4 NetBIOS Port Monitor for Windows ® 95/98/Me/ 2000/XP and Windows NT ® 4.0 This software requires the TCP/IP transport protocols to be installed on your Windows ® 95/98/Me/2 000/XP and Windows NT ® 4.0 computer. To install those protocols refer to your Windows ® documentation. If you are using the TCP/IP prot ...

  • Brother MFC-8640D - page 43

    4 - 5 NETBIOS PEER TO PEER PRINTING 7 You must now enter the server name and port n ame for the actual Print/Fax server. You can use the Br owse button to search for the Print/Fax server, select the do main/workgroup name, and then the server is listed. If the print server does not automatically appear in your browse list, then you must ensure that ...

  • Brother MFC-8640D - page 44

    NETBIOS PEER TO PEER PRINTING 4 - 6 4 Select Local Printer when you are asked how the printer is connected to your compute r, and then push Next . 5 Select the correct driver. Click Ne xt when you are done. 6 If you have selected a printer dr iver that is already being used, you have the option of either kee ping the existing driver (recommended) o ...

  • Brother MFC-8640D - page 45

    4 - 7 NETBIOS PEER TO PEER PRINTING 7 If you have selected a printer driver that is already used, you have the option of either kee ping the existing driver (recommended) or replacing it. Select the desired option and press Next . 8 Enter any desired name for the Brother printer and pre ss Next . For example, you could call the p rinter “Networke ...

  • Brother MFC-8640D - page 46

    NETBIOS PEER TO PEER PRINTING 4 - 8 Windows NT ® 4.0 / Windows ® 2000/XP 2 Click on the Port/s tab and push the Add Port button. In t he Add Port dialog, highlight Brother NetBIOS port . Click New Port and enter the port name . The default port name is BNT1. If you have already used this name, you will get an error message if you try to use it ag ...

  • Brother MFC-8640D - page 47

    5 - 1 CONFIGURING INTERNET PRINTING FOR WINDOWS ® 5 5 Configuring Internet Printing for Windows ® Internet Printing Installation Overview Brother's Brother Internet Print (BIP) software, for Windows ® 95/98/ Me and Windows NT ® 4.0, allows a PC user at one location to send a print job to a Brother Printer at a remote location via the Inter ...

  • Brother MFC-8640D - page 48

    CONFIGURING INTERNET PRINTING FOR WINDOWS ® 5 - 2 5 Windows ® 95/98/Me users can send pr int jobs using the IPP protocol via Windows ® 2000 comput er, provided that the Microsoft Internet Print Services software is installed on the client PC, Internet Information Server (IIS) is installed and running on the server and that the client PC is usin ...

  • Brother MFC-8640D - page 49

    5 - 3 CONFIGURING INTERNET PRINTING FOR WINDOWS ® ■ At the remote site, an E-mail server receives the E-mail message. The remote Print/Fax server, wh ich has its own E-mail address, uses the POP3 protocol (Post Office Protocol 3) to down load the E-mail message from the E-mail server. It then decodes the attachment and prints it out on the print ...

  • Brother MFC-8640D - page 50

    CONFIGURING INTERNET PRINTING FOR WINDOWS ® 5 - 4 Brother Internet Pr int: Using BRAdmin Professional utility to Configure the Print Server The steps required to co nfigure the Print/Fax server to receive p rint jobs from a Windows ® 95/98/Me/2000/XP and Win dows NT ® 4.0 PC running the BIP software are as follows. 1 Start BRAdmin Professional u ...

  • Brother MFC-8640D - page 51

    5 - 5 CONFIGURING INTERNET PRINTING FOR WINDOWS ® 7 The Print/Fax server is configure d by default to poll the POP3 server every 10 minutes. You may change this value, if desired. 8 If you have enabled notification, enter the address of your SMTP server (consult your network administrator if you do not know this address). 9 Press the OK button and ...

  • Brother MFC-8640D - page 52

    CONFIGURING INTERNET PRINTING FOR WINDOWS ® 5 - 6 Brother Internet Print: Installing the BIP software on Windows ® 95/98/Me/2000/XP and Windows NT ® 4.0 To install the BIP software on a Windows ® 95/98/2000/XP and Windows NT ® 4.0 PC, execute the following ste ps: Setup from CD-ROM 1 Start the CD-ROM installation menu program a ccording to the ...

  • Brother MFC-8640D - page 53

    5 - 7 CONFIGURING INTERNET PRINTING FOR WINDOWS ® 9 You will then be asked to enter the por t settings for the remote Print/Fax server: Enter any unique legal Internet E-mail address for the remote Print/Fax server (for example emailprinter@xyz.com). Note that Internet E-mail addresses cannot have spaces in them. Enter your E-mail address and the ...

  • Brother MFC-8640D - page 54

    CONFIGURING INTERNET PRINTING FOR WINDOWS ® 5 - 8 <For Windows ® 95/98/Me user s> 15 Select the desired model of the remote printer (for example, Brother HL-series). If necessary, click Have Disk to load the driver from the CD-ROM. Click Next when you are done. 16 If you have selected a printer dr iver that is already being used, you have t ...

  • Brother MFC-8640D - page 55

    5 - 9 CONFIGURING INTERNET PRINTING FOR WINDOWS ® Adding a Second Br other Internet Port You should not re-run the in stall program to add a new Brother Internet Port. Instead, press the Start button, select Settings , and open the Printers window. Click on the icon of a prin ter that is using BIP, select File from the menu bar, and then choose Pr ...

  • Brother MFC-8640D - page 56

    CONFIGURING INTERNET PRINTING FOR WINDOWS ® 5 - 10 5 When you click Next , Windows ® 2000/XP will make a connection with the URL that you specified. IF THE PRINTER DRIVER HAS ALREADY BEEN INSTALLED If the appropriate printer driver is alread y installed on your PC, Windows ® 2000/XP will automatically use that driver fo r use. In this case, you ...

  • Brother MFC-8640D - page 57

    5 - 11 CONFIGURING INTERNET PRINTING FOR WINDOWS ® Specifying a Different URL Please note that there are several possible entries that you can enter for the URL field. http://printer_ip_address:631/ipp This is the default URL and we recommend th at you use this URL. Please note the Get More Info option will not display any prin ter data. http://pr ...

  • Brother MFC-8640D - page 58

    NOVELL NETWARE PRINTING 6 - 1 6 6 Novell NetWare Printing How to Configure Novell NetWare Printing Overview Brother Print/Fax servers allow NetWare client PCs to print jobs o n the same printer as TCP/IP or other ne twork protocol users. All NetWare jobs are spooled through th e Novell server and de livered to the printer when it is available. Quic ...

  • Brother MFC-8640D - page 59

    6 - 2 NOVELL NETWARE PRINTING General Information In order to use a Brother Print/Fax server on a NetWa re network, one or more file servers must be configured with a print queue tha t the Print/Fax server can service. User s send their print requests to the file server's print queue, and the jobs are th en spooled (either directly, or in the ...

  • Brother MFC-8640D - page 60

    NOVELL NETWARE PRINTING 6 - 3 Creating a NDPS Printer Using NWADMIN for NetWare5 With NetWare 5, Novell has released a new preferred printin g system called Novell Distributed Print Services (NDPS). Before the Print/Fax server can be configured, NDPS must be in stalled on the NetWare 5 server and an NDPS Manager con figured on the server. NDPS Mana ...

  • Brother MFC-8640D - page 61

    6 - 4 NOVELL NETWARE PRINTING NDPS Broker When NDPS is installed, an NDPS broker is loaded onto the network. One of the Broker services Reso ur ce Management Service allows Printer Drivers to be installed onto the server for use with Printer Agents. To add a Printer Driver to the Broker: 1 Make sure the Resourc e Management Service is enabled. 2 Op ...

  • Brother MFC-8640D - page 62

    NOVELL NETWARE PRINTING 6 - 5 Creating a Printer Agent Follow the st eps below to create a Printer Agent for the control access printer (NDS ob ject). 1 In NetWare Administrator, select object | create | NDPS Printer . Enter the NDPS printer name. 2 If this is a new printer select create A New Printer Agent . 3 If there is already an NDS printer an ...

  • Brother MFC-8640D - page 63

    6 - 6 NOVELL NETWARE PRINTING 5 Select None for the prin ter Type, and Novell Port Handler for the Port Handler Type. Then click OK . 6 You must now specify the type of connection that you are going to use. There are four possible options. Select the LPR over IP option. 7 Enter the relevant details of the printer and Brother recommends typing Binar ...

  • Brother MFC-8640D - page 64

    NOVELL NETWARE PRINTING 6 - 7 3 One or more Print/Fax servers will appear in the list (the default node names are BRN_xxxxxx , where xx xxxx is the last six digits of the Ethernet address (MAC add ress)). 4 Select the Print/Fax server that you wish t o configure and double click it. You will be aske d for a password. The default password is access ...

  • Brother MFC-8640D - page 65

    6 - 8 NOVELL NETWARE PRINTING Creating a Network Prin t Server (NDS Queue Server) using BRAdmin Professional utility 1 Make sure that you logged in as ADMI N in NDS mode. 2 Start BRAdmin Professiona l utility. 3 One or more Print/Fax servers will appear in the list (the default node names are BRN_xxxxxx , where xx xxxx is the last six digits of the ...

  • Brother MFC-8640D - page 66

    NOVELL NETWARE PRINTING 6 - 9 e Your queue name will appear in the TREE and Context that you specified. Select the queue and click on Add . The queue name will then be transferred t o the Service Print Queues Window. You will be able to see t he TREE and Context information along with the queue na me information in this Window. f Click on the Close ...

  • Brother MFC-8640D - page 67

    6 - 10 NOVELL NETWARE PRINTING 7 Change context if required and then double click the name of the printer you created in step 3. 8 Click Assignments . 9 Click Add . 10 Change the context if necessary. 11 Select the print queue you created in step 5. 12 Click Configuration and set the Printer type to Other/Unknown . Click OK . 13 Change the context ...

  • Brother MFC-8640D - page 68

    NOVELL NETWARE PRINTING 6 - 11 18 Start the appropriate BRAdmin Pr ofessional utility, and sele ct the correct Printer/Fax server from the list (by default, the node name i s BRN_xxxxxx , where xxxxxx is the last six digits of the Ethernet address (MAC address)). 19 Double click the appropriate Brothe r Print/Fax server. Yo u will be prompted for a ...

  • Brother MFC-8640D - page 69

    6 - 12 NOVELL NETWARE PRINTING Creating a Network Prin t Server (NDS Remote Printer) using Novell NWAdmin and BRAdmin Professional utility To configure a Brother Prin t/Fax server for remote printer mode with NWADMIN (NetWare Administrator utility) and BRAdmin Professional utility, you will need to perform the following steps: 1 Make sure that the ...

  • Brother MFC-8640D - page 70

    NOVELL NETWARE PRINTING 6 - 13 12 Change context if necessary and select the print queue you created. Click OK and then OK aga in, and then exit NWADMIN. 13 Start the appropriate BRAdmin Pr ofessional utility, and sele ct the correct Print/Fax server you wish to configure (by de fault, the node names is BRN_xxx xxx , where xxxxxx is the last six di ...

  • Brother MFC-8640D - page 71

    7 - 1 PRINTING FROM A MACINTOSH ® 7 7 Printing from a Macintosh ® Printing from a Macintosh ® Using AppleTalk ® and TCP/IP or Simple Network Configuration capabilities This chapter explains how to configu re the PostScript driver on a Network. For more information o n how to configure the def ault Quick Draw driver on a Network, see the Quick S ...

  • Brother MFC-8640D - page 72

    PRINTING FROM A MACINTOSH ® 7 - 2 Quick Tips: Macintosh ® Configuration (Mac OS ® 8. 6 - 9.2) Your Brother Printer is compatible with the standard Apple LaserWriter 8 printer driver (earlier versions of the LaserWriter drivers may crash or ca use PostScript errors on large networks). If you do not have the LaserWriter 8 dr iver you must insta ll ...

  • Brother MFC-8640D - page 73

    7 - 3 PRINTING FROM A MACINTOSH ® Before you try to use the Brother print se rver, you must first enable the EtherTalk protocol from the Ne twork Control Panel on the Macintosh ® . If the EtherTalk protocol is not selected, or the Network Control Panel does not exist, you must use Ap ple's Network Installer software to add these capa bilitie ...

  • Brother MFC-8640D - page 74

    PRINTING FROM A MACINTOSH ® 7 - 4 1 Open the Chooser from the Apple Menu on the Ma cintosh ® , and then click on the LaserWriter icon (if necessary, select the appropriate AppleTalk zone from the Network Control Panel ). Figure 2 Macintosh Chooser 2 Click on the appropriate Print/Fax serve r and close the Chooser program. Yo u should now be able ...

  • Brother MFC-8640D - page 75

    7 - 5 PRINTING FROM A MACINTOSH ® How to Select the Print Server (TCP/IP) Apple has developed the “Desk top Printer” utility. This can be found from the Apple men u (this is only available from System 8.6 or later). When you run it you will see the following screen: Figure 3 Selecting LPR Printing 1 Select the Printer (LPR ) option and click O ...

  • Brother MFC-8640D - page 76

    PRINTING FROM A MACINTOSH ® 7 - 6 2 At this point we must select the correct PPD file for the machine and also configure the correct L PR information. Click the Change button in the PostScript Printer Description (PPD) File section and select the appropriate PPD file for your model. 3 Now select the Change button below the LPR Printe r Selection t ...

  • Brother MFC-8640D - page 77

    7 - 7 PRINTING FROM A MACINTOSH ® 6 You are now ready to cre ate the printer for use. To do that, click the Create button and you will see the following: Figure 6 Saving the printer to the Deskto p (screen shown is from the HL-70 50) 7 Enter the name of the printer in th e Save desktop printer As: option and click on Save . 8 We must now make this ...

  • Brother MFC-8640D - page 78

    PRINTING FROM A MACINTOSH ® 7 - 8 How to Select the Print Server (AppleTalk/EtherTalk) After installing the PPD, use the following st eps to select the p rinter driver: 1 Turn the power of the printer ON. 2 Open the Applications folder. 3 Open the Utilities folder. 4 Open the Print Center Icon. 5 Click the Add Printer button. 6 Select AppleTalk . ...

  • Brother MFC-8640D - page 79

    7 - 9 PRINTING FROM A MACINTOSH ® How to Select the Print Server (TCP/IP) After installing the PPD, use the following st eps to select the p rinter driver: 1 Turn the power of the printer ON. 2 Open the Applications folder. 3 Open the Utilities folder. 4 Open the Print Center Icon. 5 Click the Add Printer button. 6 Select LPR Printers using IP . 7 ...

  • Brother MFC-8640D - page 80

    PRINTING FROM A MACINTOSH ® 7 - 10 Changing the Configuration From a Macintosh, the easiest way to cha nge the machine or Print/ Fax server parameters is to use a web browser. Simply connect to the ma chine using the format: http://ip_address where ip_ address is the address of the machine. Other Sources of Information 1 To learn how to configure ...

  • Brother MFC-8640D - page 81

    7 - 11 PRINTING FROM A MACINTOSH ® 1 Run the Print Center software and click the Add . 2 Select Rendezvous (may be changed in the futu re version of the Mac OS ® X.) and any Simple Network Configuration compatible machines will be displayed. 3 Click the machine and then change th e Printer Model to "Brother". The PPD files that are inst ...

  • Brother MFC-8640D - page 82

    PRINTING FROM A MACINTOSH ® 7 - 12 displayed. Select th e rele vant PPD file. 4 The Simple Network Configuration compatible machine is displayed. 5 Click the machine and click the Make Default button to set the printer as the default printer.The machine is now ready to print. ...

  • Brother MFC-8640D - page 83

    8 - 1 DLC PRINTING 8 8 DLC Printing Printing from Windows NT ® 4.0 or Windows ® 2000 Overview DLC is a simple protocol that is included in Windo ws NT ® 4.0 and Windows ® 2000 as standard. It can be used on other operating systems (such as Windows ® 3.x) with the addition of vendor-supp lied software that supports the Hewlett-Packard JetDirect ...

  • Brother MFC-8640D - page 84

    DLC PRINTING 8 - 2 3 Select DLC Protocol and then OK or Add if using Windows ® 2000. You may be asked for th e location of the files. For Intel based computers, the necessary files are stored in the i386 directory of the Windows NT ® 4.0 CD-ROM. If you have a non- Intel platform, specify the co rrect directory on your Windows NT ® 4.0 CD-ROM and ...

  • Brother MFC-8640D - page 85

    8 - 3 DLC PRINTING 9 The selected print server address will then appear in the smaller box under Card Address . 10 Type in any desired name for the port (the name must not be the name of an existing port or DOS device, such as LPT1) and click OK then on the Printer P orts screen, click Next . 11 Select the correct driv er click Next . 12 Give a nam ...

  • Brother MFC-8640D - page 86

    DLC PRINTING 8 - 4 5 A list of available Print/Fax server MAC addresses (Ethern et addresses) appears in the larger box under Card Address . Select the address of the desired Print/Fax se rver (you can see the Ethernet address on the print er configuration page). 6 The selected Print/Fax server address will then a ppear in the smaller box under Car ...

  • Brother MFC-8640D - page 87

    8 - 5 DLC PRINTING The final step is to create a printer using the normal operating system printer setup method. The only difference is that instead of connecting the printer to the LPT1 para llel port, you point it to the network port you just created. Other Sources of Information Visit http://solutions.brother.com/ for more information on network ...

  • Brother MFC-8640D - page 88

    WEB BASED MANAGEMENT 9 - 1 9 9 Web Based Management How to use a Web Browser to manage your Device Overview A standard Web Browser (we recommend Netscape Navigat or version 4.0 or later/Microsoft Internet Explorer version 5.0 or later) can be used to manage your machine using the HTTP (Hyper Text Transfer Protocol). You can get the following inform ...

  • Brother MFC-8640D - page 89

    9 - 2 WEB BASED MANAGEMENT 2 To learn how to configure the IP address on your machine, see Chapter 11 of this User’s Guide. 3 The default password for Broth er print servers is access . 4 You can use a web browser on most computing platforms, for example, Macintosh and Unix user s are also able to connect to the machine and manage it. 5 You can a ...

  • Brother MFC-8640D - page 90

    FRONT PANEL SETUP MENU 10 - 1 10 10 Front Panel Setup Menu LAN Main Setup Menu With the Network (LAN) Board (NC-9100h Print/Fa x Server) installed, you can connect your mach ine into the network t o use the Internet FAX, Networ k Scanner and Network Printer. 1 Install the Network (LAN) Board (NC- 9100h). For more information, s ee Optional accessor ...

  • Brother MFC-8640D - page 91

    10 - 2 FRONT PANEL SETUP MENU Setup TCP/IP This menu has nine sections: Boot Method , IP Ad dress , Subnet Mask , Gateway , Host Name , WINS Config , WINS Server , DNS Server and APIPA . BOOT Method 1 (For MFC) Press Menu , 6 , 1 , 1 . (For DCP) Press Menu , 4 , 1 , 1 . 2 Press or to select Auto , Static , RARP , BOOTP or DHCP . 3 Press Set . 4 Pre ...

  • Brother MFC-8640D - page 92

    FRONT PANEL SETUP MENU 10 - 3 RARP mode Brother Print / Fax server IP address can be configured u sing the Reverse ARP (RARP) facility on your host computer. This is done by editing the /etc/ethers file (if this file does not exist, you can create it) with an entry similar to the following: 00:80:77:31:01:07 BRN_310107 Where the first entry is the ...

  • Brother MFC-8640D - page 93

    10 - 4 FRONT PANEL SETUP MENU In order to enable BOOTP, simply use an editor to d elete the “#” (if there is no “#”, then BOOTP is alread y enabled). Then edit the BOOTP configuration file (usually /etc/bootptab) a nd enter the name, network type (1 for Eth ernet), Etherne t address an d the IP address, subnet mask and gateway of the Prin t ...

  • Brother MFC-8640D - page 94

    FRONT PANEL SETUP MENU 10 - 5 IP Address This field displays the cu rrent IP address of the DCP/MFC. If you have selected a BOOT Method of STATIC, enter the IP address that you wish to assign to the DCP/M FC (check with your network manager for the IP address to use). If you have selected a method other than STATIC, the DCP/MFC wi ll attempt to det ...

  • Brother MFC-8640D - page 95

    10 - 6 FRONT PANEL SETUP MENU Gateway This field displays the current gat ewa y or router address used by the DCP/MFC. If you are not using DHCP or BOOTP to obtain the gateway or router address, enter th e address you wish to assign. If you do not have a gateway or router, le ave this field blank. Check with your network manager if you are un sure. ...

  • Brother MFC-8640D - page 96

    FRONT PANEL SETUP MENU 10 - 7 WINS CONFIG This selection controls how the DCP/MFC obtain s the IP address for the WINS Server. 1 (For MFC) Press Menu , 6 , 1 , 6 . (For DCP) Press Menu , 4 , 1 , 6 . 2 Press or to select Auto or Static . 3 Press Set . 4 Press Stop/Exit . Auto Automatically uses a DHCP request to determine the IP addresses for the pr ...

  • Brother MFC-8640D - page 97

    10 - 8 FRONT PANEL SETUP MENU Secondary WINS Server IP Address This field specifies the IP address of the secondary WI NS server. It is used as a backup to the Primary WINS server address. If the Primary server is unavailable, the DCP/MFC still can register itself with a secondary server. If se t to a non-ze ro value, the machin e will contact this ...

  • Brother MFC-8640D - page 98

    FRONT PANEL SETUP MENU 10 - 9 APIPA The setting of On will cause the print server to automatically allocate a Link-Local IP address in the range (16 9.254.1.0 - 169.254.254.255) when the print/fax server cannot obtain an IP address through the BOOT Method you ha ve set (Menu, 6, 1). Selecting Off means the IP address doesn’t change, when the p ri ...

  • Brother MFC-8640D - page 99

    10 - 10 FRONT PANEL SETUP MENU Setup Internet (For MFC only) This menu has five selections: Mail Address , SMTP Server , POP3 Server , Mailbox Name and Mailbox Pwd . You may find that it is more convenient to use your favorite web browser to configure these settings. Mail Address 1 Press Menu , 6 , 2 , 1 . 2 Select 1 to change. Enter the mail add r ...

  • Brother MFC-8640D - page 100

    FRONT PANEL SETUP MENU 10 - 11 Repeating letters: If you need to enter a cha racter assigned to the sa me key as the previous character, press move the cursor to the right. As you enter the E-mail address, it will appear character by ch aracter on the LCD panel. If you specify more than 16 characte rs, the LCD panel will scroll the name to the left ...

  • Brother MFC-8640D - page 101

    10 - 12 FRONT PANEL SETUP MENU POP3 Server address This field displays the Host Name or IP address of the POP3 server (incoming E-mail server) used by the Brother MFC. This address is necessary for the Internet Fax features t o function correctly. (Ex, mailhost.brothermail.net -or- 192.000 .000.001) Mailbox Name 1 Press Menu , 6 , 2 , 4 . 2 Enter t ...

  • Brother MFC-8640D - page 102

    FRONT PANEL SETUP MENU 10 - 13 Setup Mail RX (For MFC only) This menu has Five selections Auto Polling , Poll Frequency , Header , Del Error Mail and Notification . Auto Polling When set to On the MFC automatically will check the POP3 server for new messages. “ No Mail ” will be displayed if there are no E-mail messages when the POP3 server is ...

  • Brother MFC-8640D - page 103

    10 - 14 FRONT PANEL SETUP MENU 3 Press Set . 4 Press Stop/Exit . Del Error Mail When set to On , the MFC automatically deletes erro r mails that the MFC can not receive from the POP server. 1 Press Menu , 6 , 3 , 4 . 2 Press or to select On or Off . 3 Press Set . 4 Press Stop/Exit . Notification Notification feature allows a receive notification me ...

  • Brother MFC-8640D - page 104

    FRONT PANEL SETUP MENU 10 - 15 Setup Mail TX (For MFC only) This menu has three selections Sender Subject , Size Limit and Notification . Sender Subject This field displa ys the subject that is attached to the I nternet Fax data being sent from the Br other MFC to a PC (default is “ Internet Fax Job ”). 1 Press Menu , 6 , 4 , 1 . 2 Select 1 to ...

  • Brother MFC-8640D - page 105

    10 - 16 FRONT PANEL SETUP MENU Notification Notification feature when switched to On sends two f ields of data in addition to the image data which requests a notification from the receiving station for successful reception. The receivin g I-Fax station must support the MDN standard in order to be able to understand the request and consequently subm ...

  • Brother MFC-8640D - page 106

    FRONT PANEL SETUP MENU 10 - 17 Setup Relay (For MFC only) This menu has three selections RLY Broadcast , Relay Domain and Relay Report . For more information on Relay Broadcast, see Chapter 12 of this User’s Guide. Rly Broadcast This function allows the MFC to receive a d ocument over the Internet, and then relay it to other fax machines through ...

  • Brother MFC-8640D - page 107

    10 - 18 FRONT PANEL SETUP MENU Relay Report Relay Broadcast Report can be printed at the MFC used as the Relay Station for all Relay Broadcasts. Also, when the MFC is used with the Brother Network PC Fax software the MFC is acting as a Relay Station for fax transmissions from the network so a Relay Report can also be printed for confirmation of se ...

  • Brother MFC-8640D - page 108

    FRONT PANEL SETUP MENU 10 - 19 Setup Misc. Netware You can select to switch the NetWare f eature “ On ”, this allows you specify the Frame Type is item 2. 1 (For MFC) Press Menu , 6 , 6 , 1 . (For DCP) Press Menu , 4 , 2 , 1 . 2 Press or to select On or Off . 3 Press Set . 4 Press Stop/Exit . Net Frame 1 (For MFC) Press Menu , 6 , 6 , 2 . (For ...

  • Brother MFC-8640D - page 109

    10 - 20 FRONT PANEL SETUP MENU 2 Press or to select On or Off . 3 Press Set . 4 Press Stop/Exit . DLC/LLC 1 (For MFC) Press Menu , 6 , 6 , 4 . (For DCP) Press Menu , 4 , 2 , 4 . 2 Press or to select On or Off . 3 Press Set . 4 Press Stop/Exit . Net BIOS/IP The NC-9100h Print / Fax Server su pports SMB (Server Message Block) over the TCP/IP protocol ...

  • Brother MFC-8640D - page 110

    FRONT PANEL SETUP MENU 10 - 21 1 (For MFC) Press Menu , 6 , 6 , 6 . (For DCP) Press Menu , 4 , 2 , 6 . 2 Press or to select Auto/100B-FD/100B-HD/ 10B-FD/10B-HD . 3 Press Set . 4 Press Stop/Exit . Time Zone This field displays the time zone you can set for your country. The time is the difference between yo ur location and Greenwich Mean Time. This ...

  • Brother MFC-8640D - page 111

    10 - 22 FRONT PANEL SETUP MENU User Setting List (For MFC only) This feature prints a report listi ng all the current user settings. The NC-9100h Print / Fax Server Settings will be p rinted on the second page of the report. 1 Press Menu , 5 , 5 . 2 Press Start . 3 Press Stop/Exit . Setup Scan to E-mail (For MFC only) Color File Type fo r Scan to E ...

  • Brother MFC-8640D - page 112

    TCP/IP CONFIGURATION 11 - 1 11 11 TCP/IP Configuration Assigning TCP/IP Information Overview The TCP/IP protocol requires that each device on the network have it's own unique IP address. Use the following information to learn about IP address configuration. The Automatic Private IP Addressing (APIPA) protoco l automatically assigns an IP addre ...

  • Brother MFC-8640D - page 113

    11 - 2 TCP/IP CONFIGURATION Using the machine control pa nel to allocate an IP address (Models with LCD panels only) For details on how to configure IP addre ss information using the machine control panel , see chapter 10 of this User’s Guide . By using the control panel on the machin e, you can program the IP address details at the same time tha ...

  • Brother MFC-8640D - page 114

    TCP/IP CONFIGURATION 11 - 3 The BRAdmin Professional u tility can use the IPX/SPX or TCP/IP protocols to commu nicate with the Brother Print/Fax server. If you wish to use the TCP/IP prot ocol to manage the Print/Fax server make sure that the Print/Fax server has a valid IP address. If you are not using DHCP, BOOTP or RARP, you will want to change ...

  • Brother MFC-8640D - page 115

    11 - 4 TCP/IP CONFIGURATION 5 In the IP Config box, click the Static radio button. 6 Click OK . Restart the print server by using BRAdmin Professional utility or Web Browser. If you are not sure how to restart the print serve r, you may simply turn the machine’s power switch off, and then switch it on. Using BRAdmin Profession al utility and the ...

  • Brother MFC-8640D - page 116

    TCP/IP CONFIGURATION 11 - 5 Using DHCP to Conf igure the IP address The Dynamic Host Configuration Pr otocol (DHCP) is one of several automated mechanisms for IP addre ss allocation. If you have DHCP Server in your network (typically a Unix/Linux, Windows NT ® 4.0, Windows ® 2000, XP or Novell Netware network) the Print/Fax server will automatica ...

  • Brother MFC-8640D - page 117

    11 - 6 TCP/IP CONFIGURATION Using ARP to Configure the Print/ Fax Server IP Address If you are unable to use the BRAd min Professional utility or the FAXMFC’s control panel and yo ur network does not use a DHCP server, you can also use the ARP command. The ARP command is available on Windows ® systems that have TCP/IP installed as well as Unix ...

  • Brother MFC-8640D - page 118

    TCP/IP CONFIGURATION 11 - 7 Unix/Linux Systems Typically, Unix systems require the colon “ : ” character between each digit of the Ethernet address. arp -s 192.189.207.2 00:80:77:31 :01:07 To configure the Print/Fax server and to verify the connection, enter the following command ping i paddress where ipaddress is the IP address of th e Print/F ...

  • Brother MFC-8640D - page 119

    11 - 8 TCP/IP CONFIGURATION Using RARP to Config ure the IP Address The Brother Print/Fax server’s IP address ca n be configured using the Reverse ARP (rarp) facility on your host computer. This is done by editing the /etc/ethers file (if this file does not exist, you can create it) with an entry similar to the fo llowing: 00:80:77:31:01:07 BRN_3 ...

  • Brother MFC-8640D - page 120

    TCP/IP CONFIGURATION 11 - 9 Using BOOTP to Configure the IP Address BOOTP is an alternative to rarp that has the advantage of allo wing configuration of the subnet mask and gateway. In order to u se BOOTP to configure the IP address make sure th at BOOTP is installed and running on you r host computer (it shou ld appear in the /etc/services file on ...

  • Brother MFC-8640D - page 121

    11 - 10 TCP/IP CONFIGURATION Certain BOOTP host software implementations will not respond to BOOTP requests if you have not in cluded a download filename in the configuration file; if th is is the case, simply create a null file on the host and specify the name of this file and its path in the configuration file. As with rarp, the Print/Fax server ...

  • Brother MFC-8640D - page 122

    INTERNET FAX (MFC ONLY) 12 - 1 12 12 Internet FAX (MFC Only) Overview Internet Faxing (I-FAX) allows you to se nd and receive FAX documents using the Internet as the transport mechanism. Documents are transmitted in E-mail messages as atta ched TIFF-F files. This means that PC's ar e also able to receive and send documents, providing that the ...

  • Brother MFC-8640D - page 123

    12 - 2 INTERNET FAX (MFC ONLY) Getting Connected Before sending or receiving an I nternet Fax you must configure your Brother MFC to communicate with your network and mail server. You must ensure the following: a correctly configured IP address for your MFC, an E-mail address for your MFC, the mail server(s) IP address, mailbox name and password fo ...

  • Brother MFC-8640D - page 124

    INTERNET FAX (MFC ONLY) 12 - 3 Sending an Internet Fax Sending an Internet Fax is the same as sending a normal Fax. If you have already programmed th e addresses of the Internet Fax receivers into the MFC as Speed-Dial locations, you can send the Internet Fax by loadin g the document into the MFC, use the Fax Resolution key to set the preferred res ...

  • Brother MFC-8640D - page 125

    12 - 4 INTERNET FAX (MFC ONLY) By pressing the appropriate number key the correct number of times, you can access the character you want. If you want to enter a blank space, pr ess twice. If you specify more than 16 characters, the LCD pa nel will scroll the name to the left character by character. You can ent er up to 60 characters. Making correct ...

  • Brother MFC-8640D - page 126

    INTERNET FAX (MFC ONLY) 12 - 5 If you specify more than 16 characte rs, the LCD panel will scroll the name to the left character by character. You can ent er up to 60 characters. 1 Press Start to send the document. After the document is scanned, it is transmitted to t he Recipient Internet Fax Machine automatically via your SMT P server. You can ca ...

  • Brother MFC-8640D - page 127

    12 - 6 INTERNET FAX (MFC ONLY) If your machine is out of p aper when receiving data, the received data will be held in the MFC's memory. This data will be printed automatically after paper is re-inserted into th e machine. (For European, Asian and Oceanian MFCs, Memory receive must be switched “ON”.) If the received mail is not in a plain ...

  • Brother MFC-8640D - page 128

    INTERNET FAX (MFC ONLY) 12 - 7 This can be do ne using the Web Management Utility or through the front panel. The steps fo r configuring Fax Forward can be found in the User’s Guide supplied with your MFC. Relay Broadcasting This function allows the Brothe r MFC to receive a document over the Internet, and then relay it to other fax machines thro ...

  • Brother MFC-8640D - page 129

    12 - 8 INTERNET FAX (MFC ONLY) Your MFC has an E-mail address of F AX@brother.com, you wish to send a document from this machine to another MFC in England with an E-mail address of UKFAX@brother .co.uk, this machine will then forward the document to a standard fax machine using a conventional telephone line. If you r E-mail address is FAX@brother.c ...

  • Brother MFC-8640D - page 130

    INTERNET FAX (MFC ONLY) 12 - 9 Relay Broadcast from a PC You can also send E-mail from your PC and have it relayed to a conventional FAX machine. The method of ente ring the phone number of the conventional FAX machine that will re ceive the relayed E-mail will vary depending o n the mail application you are using. The following are some examples o ...

  • Brother MFC-8640D - page 131

    12 - 10 INTERNET FAX (MFC ONLY) To use this feature you must set the Notifi cation option within the Setup Mail RX and Setup Mail T X options. Setup Mail (TX) You can set the Notification option in the Setup Mail TX option to either ON or OFF. When switched to ON an additio nal field of information is sent with the image data. This field is n amed ...

  • Brother MFC-8640D - page 132

    INTERNET FAX (MFC ONLY) 12 - 11 Error mail If there is a mail delivery error while sending an Internet Fax, the mail server will send an error message back to the MFC and the error message will be printed. If there is an error while re ceiving mail, an error message will be prin ted (Example: “The messag e being sent to the MFC was not in a TIFF- ...

  • Brother MFC-8640D - page 133

    13 - 1 TROUBLESHOOTING 13 13 Troubleshooting Overview This chapter describes procedures for tro ubleshooting problems you may encounter with a Brother Print/Fa x server, it is divided into the following sections: 1 Installation Problems 2 Intermittent Problems 3 Protocol-Specific Troubleshooting 4 Internet FAX Troubleshooting Installation problems ...

  • Brother MFC-8640D - page 134

    TROUBLESHOOTING 13 - 2 2 If the configuration page prints b ut you cannot print documents, try the following a If you are using TCP/IP: Try pinging the Print/Fax server from the host operating system command prompt with the command: ping ipaddress Where ipaddress is the Print/Fax server IP addre ss (note that in some instances it can take up to two ...

  • Brother MFC-8640D - page 135

    13 - 3 TROUBLESHOOTING 3 If you cannot make any of the connections in step 2, check the following: a Make sure the machine is powe red on and on-line. b Check the cabling, network connection , and print out a configuration page in the Network STATISTICS information to see if bytes are being transmitted and received. c Check to see if there is any L ...

  • Brother MFC-8640D - page 136

    TROUBLESHOOTING 13 - 4 6 If the job exits the queue but doe s not print, make sure that yo u are not trying to print a t ext job to a PostScript printer. If you have a printer that is capable of automatic language switching, make sure that the printer is not forced into PostScript mode. Resetting the Print/Fax Sever back to factory settings (Test S ...

  • Brother MFC-8640D - page 137

    13 - 5 TROUBLESHOOTING TCP/IP Troubleshooting If you are using TCP/IP and cannot print to the Print/ Fax server and you have checked the hardware and network as d escribed in the previous steps, then check the following: Turning off the printer and then on again, Deleting and recreating the Print server and creating a new print queue in order to el ...

  • Brother MFC-8640D - page 138

    TROUBLESHOOTING 13 - 6 2 If you are using a Linux op erating system, the X-Wind ow Print tool program that is included with Linux may not properly configure the etc/printcap file for lpd operation, then you might also edit the etc/printcap file and change th e following line in the entry for the printer. if :lp = /dev/null: then to :lp = : 3 If ...

  • Brother MFC-8640D - page 139

    13 - 7 TROUBLESHOOTING 9 If you are using Sun Solaris V2.4 or earlier, there is a bug which causes long print jobs to fail when using a Printer/Fax server. If you are having trouble printing l ong jobs (over 1MB), add the line mx#0 to your etc/printcap file entry. 10 If you cannot print from DEC TCP/IP Service for VMS ( UCX), make sure that you hav ...

  • Brother MFC-8640D - page 140

    TROUBLESHOOTING 13 - 8 Windows ® 95/98/Me Peer-to-Peer (HP JetAdmin compatible method) Trouble shooting If you are having trouble printing on a W indows ® 95/98/Me Peer-to- Peer network, check the following (HP JetAdmin compatible method): 1 If the Print/Fax server does not sho w up under JetAdmin on a Windows ® 95/98/Me Peer-to-Peer network, tr ...

  • Brother MFC-8640D - page 141

    13 - 9 TROUBLESHOOTING Brother Internet Print (TCP/IP) Troubleshooting 1 The first step in troubleshooting is to make sure that you have a valid E-mail connection on both the sending PC an d the receiving Print/Fax server. Try sen ding an E-mail message from the PC to a user at the remote site who can re ceive mail via the POP3 server. If this does ...

  • Brother MFC-8640D - page 142

    TROUBLESHO OTING 13 - 10 “Get More Info” option in Wind ows ® 2000 not working “Go to Printer’s Web site” in Windows ® XP not working If you are using a URL of: http://ip_address:631 or http:// ip_address:631/ ipp , the Get More Info option in Windows ® 20 00 or the Go to Printer’s Web site option in Windows ® XP will not function. ...

  • Brother MFC-8640D - page 143

    13 - 11 TROUBLESHOOTING 1 If you changed the log in password, you must ch ange the password in both the Brother Print/Fax server (using the SET NETWARE PASSWORD command if you are using the BRConfig software or by using a web browser or the BRAdmin Professional utility) and in the fi le server (using the PCONSOLE Print Server Information Change Pas ...

  • Brother MFC-8640D - page 144

    TROUBLESHO OTING 13 - 12 2 Make sure that the AppleTa lk protocol of the Print/Fax server is enabled. 3 If you have a large ne twork, make sure that you have the L aser Writer V8.xx or equivalent driver, since ea rlier versions may cause PostScript errors. Also, verify that you get the correct printer information when you select Printer Info from t ...

  • Brother MFC-8640D - page 145

    13 - 13 TROUBLESHOOTING Internet Fax Troubleshooting 1 If there is a mail delivery error while sending an Internet Fax, the mail server will send an error me ssage back to the machine and the error message will be printed. If there is an error while receiving mail, an error message is p rinted (Ex. The message being sent to the machine was not in a ...

  • Brother MFC-8640D - page 146

    TROUBLESHO OTING 13 - 14 9 The Relay Broadcasting and Broadcasting feature s cannot be used at the same time. 10 Relay Broadcast can support the relay of a docume nt up to a maximum of 48 Fax machines through conventional telep hone lines. If sending to more than 48 locations th e sender must divide the transmission locations into 48 locations or l ...

  • Brother MFC-8640D - page 147

    14 - 1 BROTHER INTERNET FAX PRINTING SOFTWARE 14 14 Brother Internet Fax Printing Software Overview Depending on your network c onfiguration and application requirements for sending faxes via a network, you can choose between Brother Network PC FAX Software or Brother Internet Fax Printing Software. With either so ftware, viewable document such as ...

  • Brother MFC-8640D - page 148

    BROTHER INTERNET FAX PRINTING SOFTWARE 14 - 2 Installing Brother Internet Fax Printing Driver Insert the CDROM supplied with your Brother machine into your CD- ROM Drive. The installer screen will automatically start. 1 Select Install Optional Applications . 2 Select Network Print Software . 3 Highlight Brother Internet Fax Printing (BFP) Driver . ...

  • Brother MFC-8640D - page 149

    14 - 3 BROTHER INTERNET FAX PRINTING SOFTWARE During the installation you are presented with t he following screen, select the default unless you have pr eviously installed this software. If this is the case use a port numbe r that has not been previously configured. Example BFP2 You also need to enter certain informatio n into the printer driver d ...

  • Brother MFC-8640D - page 150

    BROTHER INTERNET FAX PRINTING SOFTWARE 14 - 4 Changing the BFP Port Settings If you have more than o ne networked machine with an NC-9100h Print/Fax Server you may want to change the settings of the BFP software to use an alternative machine as the network fax print server. To alter BFP settings, select Start | Settings | Printers to open the Print ...

  • Brother MFC-8640D - page 151

    14 - 5 BROTHER INTERNET FAX PRINTING SOFTWARE The following screen shows the curr ent configuration to alter this configuration, press the Configure Po rt.. . key. From the Configure Port... dialogue box you can change the settings. Relay Broadcast Function Before you can successfully use the NC-910 0h as a network fax solution you need to switch t ...

  • Brother MFC-8640D - page 152

    BROTHER INTERNET FAX PRINTING SOFTWARE 14 - 6 If you do not know the password contact you Network Administrator. Then browse to Internet Setting s and Relay Function. In order for the machine to receive data from the desktop and then send this information (network fax) to other fax machines the “Relay Broadcast Function” must be switched “ON? ...

  • Brother MFC-8640D - page 153

    14 - 7 BROTHER INTERNET FAX PRINTING SOFTWARE Uninstalling from Windows ® 95/98/Me/2000/XP and Windows NT ® 4.0 Select Start / Settings / Control Panel and then double click the Add or Remove programs icon. From the list of installed programs select the Brother Internet Fax Vx .xx as shown below then click the Add/Remove button. You also need to ...

  • Brother MFC-8640D - page 154

    BROTHER INTERNET FAX PRINTING SOFTWARE 14 - 8 Using the BFP Address Book This utility can administer the Fax addr esses, Internet Fax addresses and E-mail address of all t he contacts that you wish to use with the BFP Software. Additionally you can create Groups of con tacts that you may wish to broadcast documents to. From the Start menu, select P ...

  • Brother MFC-8640D - page 155

    14 - 9 BROTHER INTERNET FAX PRINTING SOFTWARE 2 In the Brother Address Book Mem ber Setup dialog box, type the member's information. Name and Fax are required f ields. You can also enter the an E-mail contact address and machine address for the address book member Click the OK button to save the member's information. Setting Up a Group fo ...

  • Brother MFC-8640D - page 156

    BROTHER INTERNET FAX PRINTING SOFTWARE 14 - 10 2 Type the name of the new group in the Group Name field. 3 In the Available Names box, select each member to be included in the Group, and then click Ad d>> . 4 Members you add to the group will be liste d in the Group Members box. 5 After all the members have been ad ded, click OK . Editing Mem ...

  • Brother MFC-8640D - page 157

    14 - 11 BROTHER INTERNET FAX PRINTING SOFTWARE 3 If you are exporting to an ASCII file , select Divide Character - Tab or Comma . This selection inserts a Tab or Comma between each data field when it is Exported. 4 Select the OK button to save the data. 5 Type in the name of the file, and t hen select Save . 6 If you are creating a Vca rd, you must ...

  • Brother MFC-8640D - page 158

    BROTHER INTERNET FAX PRINTING SOFTWARE 14 - 12 Clicking OK with start the BFP dialogue box as illustrated below. From this dialogue box you can either specify a n address in the address line or select a location from the ad dress book. If you wish to type more than o ne location in the ad dress line make sure th ey are separated by “;”. When en ...

  • Brother MFC-8640D - page 159

    APPENDIX A - 1 A A Appendix Appendix A General Information You can change the configuration of your Print /Fax server using any of the following methods. • Brother BRAdmin Professional ut ility for Windows ® 95/98/ Me / 2000/XP and Windows NT ® 4.0. • Brother Web BRAdmin Professional utility for IIS* • HTTP (using a web browser) • WebJetA ...

  • Brother MFC-8640D - page 160

    APPENDIX A - 2 HTTP (Recommended) Use your favorite web browser to connect to th e Brother Print/Fax server. This will allow you to configure machine and/or Prin t/Fax server parameters. WebJetAdmin Brother's Print/Fax server range is HP WebJetAdmin compatible. ...

  • Brother MFC-8640D - page 161

    A - 3 APPENDIX Appendix B Using Services General A service is a resource that can be accessed by computers that wish to print to the Brother Print/ Fax server. The Brother Print/Fax server provides the following prede fined services (do a SHOW SERVICE command in the Brother Print/Fax serve r remote console to see a list of available services): Ente ...

  • Brother MFC-8640D - page 162

    APPENDIX A - 4 Appendix C Reloading the Print / FAX Server Firmware General The firmware on the Print/Fax server is st ored in flash memory. This means that you can upgrade t he firmware by do wnloading the appropriate update file. To get the la test firmware update, visit the Brother Solutions web site at http://solution s.brother.com/ The Print / ...

  • Brother MFC-8640D - page 163

    A - 5 APPENDIX Reloading firmware using BRAdmin Professional utility The BRAdmin Professional ut ility can be used to easily re-p rogram your Brother Print/Fax server. 1 Start BRAdmin Professiona l utility. 2 Highlight the appropriate Print/Fax server. Then press select the Control menu and choose Load Firmware. You can select more than one Print/F ...

  • Brother MFC-8640D - page 164

    APPENDIX A - 6 5 Netware GET from a server You must have a Netware server on your network (running IPX/ SPX) and you must store the new firmware file in the SYS/Login directory of the server. In this case, your PC makes the Print/Fax server read the firmware data from the assigned Netware server, the Print/Fax server attache s to the Netware server ...

  • Brother MFC-8640D - page 165

    A - 7 APPENDIX ftp> quit When you see 226 Data Tra nsfer OK/Entering FirmWareUpdate mode , you ca n be sure that the firmware file is being transferred to the Prin t/Fax server. If you do not see this message, the file you are sending to the printer will either be ignored or the printer will print garbage. You must use the “bin” command to p ...

  • Brother MFC-8640D - page 166

    APPENDIX A - 8 Appendix D Updating other MFC’s through the Network It is possible to program Brother MFC’s on the network with either settings from an already programmed MFC or with data from the Brother Network PC-FAX Address Book. See Chapte r 6 of the Software User’s Guide on the CD-ROM. When Brother Network PC-FAX in used from a PC that h ...

  • Brother MFC-8640D - page 167

    A - 9 APPENDIX When you select this option BRAd min reads th e telephone settings from that machine (if there are any programmed) into Brother PC- FAX Address Book. Illustrated below is the Brother Address Book, on th e left are One- Touch / Speed-Dial numbe rs read from the machine. On the right is the Brother Address Book. It is n ow possible to ...

  • Brother MFC-8640D - page 168

    APPENDIX A - 10 Highlight singular or multiple networked Brother MFC’s in the main BRAdmin window by highlighting and pressing the shift key on your keyboard. Right click the highlighted MFC’s and press Send Auto Dial . The new data is then sent to a ll the highlighted MFC’s. A dialog box is displayed showing t he upload status of curr ent MF ...

  • Brother MFC-8640D - page 169

    A - 11 APPENDIX Appendix E Specifications Operation System Support Windows ® 95 /98/98SE/Me/2000/XP and Windows NT ® 4.0 Unix systems supporting LPD Mac OS ® 8.6 - 9.1 / Mac OS ® 10.1 - 10.2.1 or gre ater Protocol Support ■ TCP/IP (including the following): RARP, BOOTP, DHCP, APIPA, NetBIOS, WINS, DNS Resolver, LPR/LPD, Port9100, SMTP/ POP3, ...

  • Brother MFC-8640D - page 170

    APPENDIX A - 12 Internet Fax T.37 Simple mode Tiff-F Profile-S Resolution: 200x100, 2 00x200, 204x98, 204x196dpi Coding System: MH Width: 1728 dot Fax / E-mail / I-Fax Forwardi n g / Pagi ng fe at ure Scan to key: E-mail / OCR / Imag e / File Internet F ax Relay E-mail Relay Relay Broadcast Please check the User’s Guide for your Brother MFC to ve ...

  • Brother MFC-8640D - page 171

    A - 13 APPENDIX AppleTalk Connection ■ Computer: Ethernet ready Power Macintosh ■ RAM: 32MB or more (64MB or more recommended) for Mac OS ® 8.6 - 9.2 128MB or more (1 60MB or more recom mended) for Mac O S ® X 10.1 - 10 .2.1 or gre ate r ■ OS: Mac OS ® 8.6 - 9.1 / Mac OS ® 10.1 - 10.2.1 or greater Open Transport 1.3 or later Management Ut ...

  • Brother MFC-8640D - page 172

    APPENDIX A - 14 Function Table and Default Factory Se ttings LEVEL ONE LEVEL TWO LEVEL THREE OPTIONS OPTION S FA C TO RY SETTIN G 6.LAN (MFC) 4.LAN (DCP) 1.Setup TCP/IP 1.BOOT Method Auto/ S tatic/ RARP/ BOOTP/ DHCP Auto 2.IP Address [ 000-255].[000-2 55].[000- 255].[000-255] [169].[254]. [001- 254].[000-255] 3.Subnet Mask [000-255].[0 00-255].[000 ...

  • Brother MFC-8640D - page 173

    A - 15 APPENDIX *1: ‘IP Address’ and ‘Subnet Mask’ se tting will be chan ged by APIPA setting. *2: ‘NET FRAME’ setting is available when ‘ NETWARE’ is ‘ON’. 6.Setup Misc. (MFC) 2.(DCP) 1.Netware On/ Off *1 On 2.Net Frame *2 Auto/ 8023/ ENET/ 8022/ SNAP Auto 3.AppleT alk On/ Off On 4.DLC/LLC On/ Off On 5.Net BIOS/IP On/ Off On 6. ...

  • Brother MFC-8640D - page 174

    INDEX I - 1 I INDEX A AIX ...................................... 1-3 AIX 4.0 ................................ 1-8 AppleTalk ....... 7-1 , 7-3 , 7-8 , 13-2 , 13-11 ARP ...................1-2 , 11-1 , 11-6 B Berkeley UNIX .................... 1-1 BFP Address Book ............ 14-9 BFP Port ........................... 14-4 BINARY_P1 ......... 1-2 , 1- ...

  • Brother MFC-8640D - page 175

    I - 2 INDEX N NDPS .......................... 6-2 , 6-3 NDS .................................... 6-2 NetBIOS .................... 4-1 , 13-8 NetWare 3 .......................... 6-2 Netware 3 ........................... 6-6 NetWare 4 ................... 6-2 , 6-6 NetWare 5 .......................... 6-2 Netware GET ...................... A-6 networ ...

Produzent Brother Kategorie Printer

Dokumente, die wir vom Produzenten des Geräts Brother MFC-8640D erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Brother
- Bedienungsanleitungen MFC-8640D
- Produktkarten Brother
- Informationsbroschüren
- oder Energieetiketten Brother MFC-8640D
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Brother MFC-8640D.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Brother MFC-8640D, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Brother MFC-8640D. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Brother MFC-8640D ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Brother MFC-8640D, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Brother MFC-8640D hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Brother MFC-8640D verständlich ist.

Eine gänzliche Bedienungsanleitung von Brother sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Brother MFC-8640D bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Brother MFC-8640D befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Brother MFC-8640D, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Brother MFC-8640D - die uns die ersten Schritte während der Nutzung von Brother MFC-8640D erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Brother MFC-8640D hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Brother MFC-8640D im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Brother MFC-8640D?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Brother MFC-8640D nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Brother MFC-8640D hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)