Deutsch dropdown-ico

Bedienungsanleitung Maytag MDG30MNV

36 Seiten 1.46 mb
Download

Zur Seite of 36

Summary
  • Maytag MDG30MNV - page 1

    RET AIN THESE INSTRUCTIONS IN A SAFE PLACE FOR FUTURE REFERENCE MDG30PNH / MDG30MNV Installa tion Manual 30 lb Single P oc k et / Phase 7 / Non-Coin with Fire Suppression System Part No. 1 13307 - 7 A VER TISSEMENT : Assurez-vous de bien suivre les instructions données dans cette notice pour réduire au minimum le risque d’incendie ou d’explos ...

  • Maytag MDG30MNV - page 2

    Retain This Manual In A Safe Place For Futur e Refer ence This product embodies advanced concepts in engineering, design, and safety . If this product is properly maintained, it will provide many years of efficient, trouble free, and most importantly safe operation. ONLY qualified technicians should service this equipment. OBSER VE ALL SAFETY PRECA ...

  • Maytag MDG30MNV - page 3

    IMPOR T ANT YOU MUST DISCONNECT AND LOCKOUT THE ELECTRIC SUPPL Y AND THE GAS SUPPL Y OR THE STEAM SUPPL Y BEFORE ANY COVERS OR GUARDS ARE REMOVED FROM THE MACHINE T O ALLOW ACCESS FOR CLEANING , ADJUSTING , INST ALLA TION, OR TESTING OF ANY EQUIPMENT PER OSHA (Occupational Safety and Health Administration) ST ANDARDS. W ARNING CHILDREN SHOULD NOT B ...

  • Maytag MDG30MNV - page 4

    W ARNING The dryer must never be operated with any of the back guards, outer tops, or service panels removed. PERSONAL INJUR Y OR FIRE COULD RESUL T . IMPOR T ANT PLEASE OBSER VE ALL SAFETY PRECAUTIONS displayed on the equipment and/or specified in the installation manual included with the dryer . W ARNING DR YER MUST NEVER BE OPERA TED WITHOUT THE ...

  • Maytag MDG30MNV - page 5

    SECTION I SAFETY PRECAUTIONS ........................................................................................................ 2 SECTION II SPECIFICA TIONS .................................................................................................................. 4 SECTION III INST ALLA TION PROCEDURES ................................ ...

  • Maytag MDG30MNV - page 6

    2 Maytag Co. 1 13307 - 7 SECTION I SAFETY PRECAUTIONS W ARNING: For your safety , the information in this manual must be followed to minimize the risk of fire or explosion or to prevent property damage, personal injury , or loss of life. W ARNING: The dryer must never be operated with any of the back guards, outer tops, or service panels removed. P ...

  • Maytag MDG30MNV - page 7

    1 13307 - 7 Maytag Co. 3 W ARNING: DO NOT use heat for drying articles that contain plastic, foam, sponge rubber , or similarly textured rubber materials. Drying in a heated basket (tumbler) may damage plastics or rubber and may be a fire hazard. 7. A program should be established for the inspection and cleaning of lint in the burner area, exhaust ...

  • Maytag MDG30MNV - page 8

    4 Maytag Co. 1 13307 - 7 M AXI M U M CAPACI TY ( DRY WE I G H T ) 30 lbs 13. 6 kg BASKET ( T U M BLER) DI AM E TER 32 - 3 / 4” 83. 2 cm BASKET ( T U M BLE R) DEPTH 25 - 5/ 8” 65. 1 cm BASKET ( T U M BLE R) M O TO R 1/ 2 h p 0. 373 kW D OOR OP E N IN G (D IA ME T E R ) 2 1-1 /2 ” 54. 61 cm BASKET ( T U M BLE R) V O L U M E 12 . 5 c u f t 0. 35 ...

  • Maytag MDG30MNV - page 9

    1 13307 - 7 Maytag Co. 5 NOTE: The manufacturer reserves the right to make changes in specifications at any time without notice or obligation. S pecifications ...

  • Maytag MDG30MNV - page 10

    6 Maytag Co. 1 13307 - 7 SECTION III INST ALLA TION PROCEDURES Installation should be performed by competent technicians in accordance with local and state codes. In the absence of these codes, the installation must conform to applicable American National Standards: ANSI Z223.1- LA TEST EDITION (National Fuel Gas Code) or ANSI/NFP A NO. 70-LA TEST ...

  • Maytag MDG30MNV - page 11

    1 13307 - 7 Maytag Co. 7 4. Provisions for adequate air supply must be provided as noted in this manual (refer to Fr esh Air Supply Requirements in Section D ). 5. Clearance provisions must be made from combustible construction as noted in this manual (refer to Dryer Enclosure Requirements in Section C ). 6. Provisions must be made for adequate cle ...

  • Maytag MDG30MNV - page 12

    8 Maytag Co. 1 13307 - 7 NOTE: Air considerations are important for proper and efficient operation. Dryers may be positioned sidewall to sidewall. However , a 1/16” (1.59 mm) minimum allowance must be made for opening and closing of the control door . It is suggested that the dryer be positioned about 2 feet (0.61 meters) away from the nearest ob ...

  • Maytag MDG30MNV - page 13

    1 13307 - 7 Maytag Co. 9 E. EXHAUST REQUIREMENTS Exhaust ductwork should be designed and installed by a qualified professional. Improperly sized ductwork will create excessive back pressure which results in slow drying, increased use of ener gy , and shutdown of the burner by the airflow (sail) switch, burner hi-limits, or lint chamber hi-limit pro ...

  • Maytag MDG30MNV - page 14

    10 Maytag Co. 1 13307 - 7 NOTE 1 Opening must be 2-inches (5.08 cm) larger than the duct (all the way around). The duct must be centered within this opening. NOTE 2 Distance should be 2 times the diameter of the duct to the nearest obstruction. SINGLE DR YER VENTING IMPOR T ANT : For extended ductwork runs, the cross section area of the ductwork ca ...

  • Maytag MDG30MNV - page 15

    1 13307 - 7 Maytag Co. 11 MUL TIPLE DR YER (COMMON) VENTING IMPOR T ANT : For extended ductwork runs, the cross section area of the ductwork can only be increased to an extent. When the ductwork approaches the maximum limits as noted in this manual, a professional heating, ventilating, and air -conditioning (HV AC) firm should be consulted for prop ...

  • Maytag MDG30MNV - page 16

    12 Maytag Co. 1 13307 - 7 F . ELECTRICAL INFORMA TION 1. Electrical Requirements ALL electrical connections must be made by a properly licensed and competent electrician. This is to ensure that the electrical installation is adequate and conforms to local and state regulations or codes. In the absence of such codes, ALL electrical connections, mate ...

  • Maytag MDG30MNV - page 17

    1 13307 - 7 Maytag Co. 13 ELECT R I CAL SER V I C E S PE CI FI CAT I O N S ( PE R D R Y ER ) IMP OR T AN T : NO TES : A . B. 208 V AC AN D 240 V A C AR E NO T TH E SA M E . When o rder ing, sp ec if y exac t vol t ag e . Wh en f u ses are u sed th e y mu s t be du al el em en t, t ime del ay , cu rr en t l imit in g, cl ass R K 1 or R K5 ON LY . Ca ...

  • Maytag MDG30MNV - page 18

    14 Maytag Co. 1 13307 - 7 a . Single-Phase (1ø) W iring Connections/Hookup The electrical input connections on ALL single-phase (1ø) gas dryers are made into the rear service box located at the upper left area of the dryer . S i ng l e - P ha s e E le c t r i c a l L e a d C o nne c t i o ns Bl ac k + Posit iv e Wh i te or R ed + Ne utra l or L2 ...

  • Maytag MDG30MNV - page 19

    1 13307 - 7 Maytag Co. 15 G . GAS INFORMA TION It is your responsibility to have ALL plumbing connections made by a qualified professional to ensure that the gas plumbing installation is adequate and conforms to local and state regulations or codes. In the absence of such codes, ALL plumbing connections, materials, and workmanship must conform to t ...

  • Maytag MDG30MNV - page 20

    16 Maytag Co. 1 13307 - 7 T Y P E OF GA S N A TU RAL LI Q U I D PRO PAN E Ma n i fol d P res su re* 3 .5 i n c h es W .C . 8. 7 m b 10. 5 i n ch es W . C. 26.1 mb In -Lin e Pressu r e 6.0 - 12. 0 i n ch es W . C. 14.92 - 29. 9 m b 1 1 .0 i n ch es W .C . 27. 4 m b T Y P E OF GA S Li qu id Propa n e Conv e r s io n K it Part N u m ber Bt u Per H ou ...

  • Maytag MDG30MNV - page 21

    1 13307 - 7 Maytag Co. 17 3. Piping Connections ALL components/materials must conform to National Fuel Gas Code Specifications ANSI Z223.1-LA TEST EDITION, or in Canada, CAN/CGA-B149.1-M91 (Natural Gas) or CAN/CGA-B149.2-M91 (Liquid Propane [L.P .] Gas) or LA TEST EDITION (for General Installation and Gas Plumbing), as well as local codes and ordin ...

  • Maytag MDG30MNV - page 22

    18 Maytag Co. 1 13307 - 7 NOTE: A water column test pressure of 3.5 inches (8.7 mb) for natural gas and 10.5 inches (26.1 mb) for liquid propane (L.P .) dryers is required at the gas valve pressure tap of each dryer for proper and safe operation. A 1/8” N.P .T . plugged tap, accessible for a test gauge connection, must be installed in the main ga ...

  • Maytag MDG30MNV - page 23

    1 13307 - 7 Maytag Co. 19 I. PREOPERA TIONAL TESTS ALL dryers are thoroughly tested and inspected before leaving the factory . However , a preoperational test should be performed before the dryer is publicly used. It is possible that adjustments have changed in transit or due to marginal location (installation) conditions. 1. T urn on electric powe ...

  • Maytag MDG30MNV - page 24

    20 Maytag Co. 1 13307 - 7 NOTE: If computer program changes are required, refer to the computer programming section of the manual supplied with the dryer . 6. The dryer should be operated through one (1) complete cycle to ensure that no further adjustments are necessary and that ALL components are functioning properly . BASKET (TUMBLER) COA TING Th ...

  • Maytag MDG30MNV - page 25

    1 13307 - 7 Maytag Co. 21 REVERSING TIMER SPIN/DWELL ADJUSTMENTS T imer models have an electronic reversing timer in the electrical service box, which is located in the upper left rear area of the dryer . Both the Dwell (stop) T ime and the basket (tumbler) Spin T ime are adjustable by mode selection switches located on the electronic timer (as not ...

  • Maytag MDG30MNV - page 26

    22 Maytag Co. 1 13307 - 7 SECTION IV SER VICE/P AR TS INFORMA TION A. SER VICE Service must be performed by a qualified trained technician, service agency , or gas supplier . If service is required, contact the dealer from whom the Maytag equipment was purchased. If the dealer cannot be contacted or is unknown, contact the Maytag Co. for a dealer i ...

  • Maytag MDG30MNV - page 27

    1 13307 - 7 Maytag Co. 23 SECTION V W ARRANTY INFORMA TION A. RETURNING W ARRANTY CARDS 1. Before any dryer leaves the manufacturer’ s test area, a warranty card is placed on the back side of the main door glass. These warranty cards are intended to serve the customer where we record the individual installation date and warranty information to be ...

  • Maytag MDG30MNV - page 28

    24 Maytag Co. 1 13307 - 7 SECTION VI ROUTINE MAINTENANCE A. CLEANING A program and/or schedule should be established for periodic inspection, cleaning, and removal of lint from various areas of the dryer , as well as throughout the ductwork system. The frequency of cleaning can best be determined from experience at each location. Maximum operating ...

  • Maytag MDG30MNV - page 29

    1 13307 - 7 Maytag Co. 25 90 DA YS Inspect and remove lint accumulation in customer furnished exhaust ductwork system and from dryer ’ s internal exhaust ducting. W ARNING: THE ACCUMULA TION OF LINT IN THE EXHAUST DUCTWORK CAN CREA TE A POTENTIAL FIRE HAZARD. W ARNING: DO NOT OBSTRUCT THE FLOW OF COMBUSTION AND VENTILA TION AIR. W ARNING: INSPECT ...

  • Maytag MDG30MNV - page 30

    26 Maytag Co. 1 13307 - 7 SECTION VII DA T A LABEL INFORMA TION When contacting the Maytag dealer , certain information is required to ensure proper service/parts information. This information is on the dryer data label affixed to the left side panel area behind the top control (access) door . When contacting the Maytag Co. , please have the model ...

  • Maytag MDG30MNV - page 31

    1 13307 - 7 Maytag Co. 27 SECTION VIII PROCEDURE FOR FUNCTIONAL CHECK OF REPLACEMENT COMPONENTS 1. Microprocessor Controller (Computer) Board a . Upon completing installation of the replacement microprocessor controller (computer) board, reestablish power to the dryer . b. Start the drying cycle by pressing any of the preset cycles in letters A-F . ...

  • Maytag MDG30MNV - page 32

    28 Maytag Co. 1 13307 - 7 2. For Models with Direct Spark Ignition (DSI) Module (T ype I) Theory of Operation: Start the drying cycle. When the gas burner ignites within the chosen trial for ignition time (6-seconds), the flame sensor detects gas burner flame and signals the DSI module to keep the gas valve open as long as there is a call for heat. ...

  • Maytag MDG30MNV - page 33

    1 13307 - 7 Maytag Co. 29 The exclusive fire suppression system will extinguish fires that may start in the drying basket (tumbler). A series of sensors positioned throughout the basket (tumbler) and interfaced with the Phase 7 microprocessor controller (computer) will trigger the fire suppression system water jet(s) to extinguish the flames quickl ...

  • Maytag MDG30MNV - page 34

    30 Maytag Co. 1 13307 - 7 INST ALLA TION 1. Requirements The fire suppression system must be supplied with a minimum water pipe size of 1/2” and be provided with 40 psi +/- 20 psi (2.75 bar +/- 1.37 bar) of pressure. For use of optional manual bypass, a second source with the same piping and pressure requirements is required. Flexible 1/2 feeds m ...

  • Maytag MDG30MNV - page 35

    1 13307 - 7 Maytag Co. 31 W ARNING: If the water in the supply line or water solenoid valve freezes, the fire suppression system will be INOPERA TIVE!! T ypical W ater Supply OPTIONAL MANUAL BYP ASS Provisions are made in the dryer ’ s fire suppression system for the installation of an optional manual bypass. The connections for the manual bypass ...

  • Maytag MDG30MNV - page 36

    Part No. 1 13307 7 - 06/26/08 - 0 ...

Produzent Maytag Kategorie Clothes Dryer

Dokumente, die wir vom Produzenten des Geräts Maytag MDG30MNV erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Maytag
- Bedienungsanleitungen MDG30MNV
- Produktkarten Maytag
- Informationsbroschüren
- oder Energieetiketten Maytag MDG30MNV
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Maytag MDG30MNV.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Maytag MDG30MNV, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Maytag MDG30MNV. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Maytag MDG30MNV ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Maytag MDG30MNV, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Maytag MDG30MNV hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Maytag MDG30MNV verständlich ist.

Eine gänzliche Bedienungsanleitung von Maytag sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Maytag MDG30MNV bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Maytag MDG30MNV befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Maytag MDG30MNV, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Maytag MDG30MNV - die uns die ersten Schritte während der Nutzung von Maytag MDG30MNV erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Maytag MDG30MNV hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Maytag MDG30MNV im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Maytag MDG30MNV?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Maytag MDG30MNV nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Maytag MDG30MNV hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)