Bedienungsanleitung Schumacher SC-200A

41 Seiten 1.89 mb
Download

Zur Seite of 41

Summary
  • Schumacher SC-200A - page 1

    0099000981WB-03 Automatic Battery Charger / Maintainer Cargador de batería automático / Mantenedor Model / Modelo: SC-200A OWNER’S MANUAL MANUAL DEL USUARIO Volt ag e / T ensi ón: 6 , 1 2 Amp er ag e / Amp er aje: 4 , 2 READ THE ENTIRE MANUAL BEFORE USING THIS PRODUCT . F AILURE TO DO SO COULD RESUL T IN SERIOUS INJURY OR DEA TH. LEA EL MANUAL ...

  • Schumacher SC-200A - page 2

    • 2 • IMPORT ANT : READ AND SA VE THIS SAFETY AND INSTRUCTION MANUAL. SA VE THESE INSTRUCTIONS – This manual will show you how to use your charger safely and effectively . Please read, understand and follow these instructions and precautions carefully , as this manual contains important safety and operating instructions. The safety messages u ...

  • Schumacher SC-200A - page 3

    • 3 • T o reduce the risk of damage to the electric plug or cord, pull by 1.4 the plug rather than the cord when disconnecting the charger . An ext ension cord sh ould no t be u sed unl ess abs olutely necess ary . 1.5 Use of an improper extension cord could result in a risk of re and electric shock. If an extension cord must be used, make s ...

  • Schumacher SC-200A - page 4

    • 4 • This charger employs parts, such as switches and circuit breakers, 1.12 that tend to produce arcs and sparks. If used in a garage, locate this charger 18 inches (46 cm) or more above oor level. PERSO NA L PRECAUTI ONS 2. RISK OF EXPLOSIVE GASES. NEVER smoke or allow a spark or ame in the 2.1 vicinity of a battery or engine. Remove p ...

  • Schumacher SC-200A - page 5

    • 5 • PRE P A RI NG TO CHA RGE 3. RISK OF CONT ACT WITH BA TTERY ACID. BA TTERY ACID IS A HIGHL Y CORROSIVE SULFURIC ACID. If it is necessary to remove the battery 3.1 from the vehicle to charge it, always remove the grounded terminal rst. Make sure all of the accessories in the vehicle are off to prevent arcing. Be sure the area around the ...

  • Schumacher SC-200A - page 6

    • 6 • Never place the charger directly above the battery being charged; 4.2 gases from the battery will corrode and damage the charger . Do not set the battery on top of the charger . 4.3 Never allow battery acid to drip onto the charger when reading the 4.4 electrolyte specic gravity or lling the battery . Do not operate the charger in a ...

  • Schumacher SC-200A - page 7

    • 7 • For a negative-grounded vehicle, connect the POSITIVE (RED) 6.5 clip from the battery charger to the POSITIVE (POS, P , +) ungrounded post of the battery . Connect the NEGA TIVE (BLACK) clip to the vehicle chassis or engine block away from the battery . Do not connect the clip to the carburetor , fuel lines or sheet-metal body parts. Conn ...

  • Schumacher SC-200A - page 8

    • 8 • Do not face the battery when making the nal connection. 7.5 Connect charger AC supply cord to electrical outlet. 7.6 When disconnecting the charger , always do so in the reverse 7.7 order of the connecting procedure and break the rst connection while as far away from the battery as practical. A marine (boat) battery must be removed ...

  • Schumacher SC-200A - page 9

    • 9 • F E AT U R E S 9. Amp/V olt Selector Switch 1. Battery Status LEDs 2. Battery Clamp Cable Assembly 3. Ring T erminal Cable Assembly 4. 12V Plug Cable Assembly 5. 1 2 3 4 5 ASS EMB L Y I NSTRU CTI ONS 10. Remove all cord wraps and uncoil the cables prior to using the battery charger . CONT ROL P AN EL 1 1. LED Indicators CHECK (red) LED li ...

  • Schumacher SC-200A - page 10

    • 10 • V oltage Selector Switch Use the V oltage Se lect or swit ch to set the out put vo ltag e o f t he c har ger to either 6 volts or 12 volts to match the battery being charged. OPE R A TI NG I NSTRU CTI ONS 12. This battery charger must be properly assembled in accordance with the assembly instructions before it is used. The charger does n ...

  • Schumacher SC-200A - page 11

    • 1 1 • 50 Amp Battery Clips Connect the end of the charger output cable to the end of the 1. 50 Amp Battery clips cable. Follow the steps in sections 6 and 7 to connect the output clips 2. to the battery . After a good electrical connection is made to the battery , plug 3. the power cord into a 120V AC electrical wall outlet. Make sure to plac ...

  • Schumacher SC-200A - page 12

    • 12 • Battery Connection Indicator If the charger does not detect a properly connected battery , the CHECK LED will light. Charging will not begin if the CHECK LED is on. Automatic Charging Mode When an Automatic Charge is performed, the charger switches to the Maintain Mode (see below) automatically after the battery is charged. For a battery ...

  • Schumacher SC-200A - page 13

    • 13 • maintaining a fully charged large battery , you will be properly utilizing the battery charger . However , if you were to use this battery charger to charge a large battery , such as a marine deep cycle battery , that was not fully charged, you may lose some of the battery’s capacity . This would cause the large battery to be unable to ...

  • Schumacher SC-200A - page 14

    • 14 • 4 Amp, 6 V olt Battery Battery Condition Ampere Hour Battery Capacity Approximate Average Charge T ime in Hours 50% Discharged 100% Discharged 10 1.6 3.2 12 2.0 4.0 20 3.2 6.4 MA INT ENA NCE I NSTR UCTI ON S 1 4. After use and before performing maintenance, unplug and 14.1 disconnect the battery charger (see sections 6, 7 and 8). Use a d ...

  • Schumacher SC-200A - page 15

    • 15 • TROUBL ESHOO TING 16. PROBLEM POSSIBLE CAUSE REASON/SOLUTION Battery clips do not spark when touched together . The charger is equipped with an auto-start feature. It will not supply current to the battery clips until a battery is properly connected. Meaning, the clips will not spark if touched together . No problem; this is a normal con ...

  • Schumacher SC-200A - page 16

    • 16 • PROBLEM POSSIBLE CAUSE REASON/SOLUTION The charger is making an audible clicking sound. (continued) Reverse connections at battery . Shut the charger off and correct the lead connections. Charger makes a loud buzz or hum. T ransformer laminations vibrate (buzz). No problem; this is a normal condition. CHECK BA TTERY (red) LED is on. Clip ...

  • Schumacher SC-200A - page 17

    • 17 • PROBLEM POSSIBLE CAUSE REASON/SOLUTION Charger will not turn on when properly connected. AC outlet is dead. Poor electrical connection. Connections are reversed. Battery voltage is too low . Battery is defective. Check for open fuse or circuit breaker supplying AC outlet. Check power cord and extension cord for loose tting plug. Unplu ...

  • Schumacher SC-200A - page 18

    • 18 • If the above solutions do not eliminate the problem or for information about troubleshooting, call toll-free from anywhere in the U.S.A. 1-800-621-5485 7:00 am to 5:00 pm Central T ime Monday through Friday LI MIT ED WAR R ANT Y 18. W ARRANTY NOT V ALID IN MEXICO. SCHUMACHER ELECTRIC CORPORA TION, 801 BUSINESS CENTER DRIVE, MOUNT PROSPEC ...

  • Schumacher SC-200A - page 19

    • 19 • Some states do not allow the exclusion or limitation of incidental or consequential damages or length of implied warranty , so the above limitations or exclusions may not apply to you. This warranty gives you specic legal rights and it is possible you may have other rights which vary from this warranty . THIS LIMITED W ARRANTY IS THE ...

  • Schumacher SC-200A - page 20

    • 20 • 5 YEAR LIMITED W ARRANTY PROGRAM REGISTRA TION MODEL: ___________________ DESCRIPTION: ___________________________ This is the only express limited warranty , and the manufacturer neither assumes nor authorizes anyone to assume or make any other obligation. There is no other warranty , other than what is described in the product owner ? ...

  • Schumacher SC-200A - page 21

    • 21 • PROGRAMA DE REGISTRO DE 5-AÑOS DE GARANTÍA LIMIT ADA MODELO: ___________________ DESCRIPCIÓN: ___________________________ Esta es la única garantía limitada expresa, y el productor no autoriza ni otorga a alguien a realizar alguna otra obligación. No existe ninguna otra garantía más que la descrita en el manual del dueño. La tar ...

  • Schumacher SC-200A - page 22

    • 22 • IMPORT ANTE: LEA Y GUARDE ESTE MANUAL DE INSTRUCCIONES Y SEGURIDAD. GUARDE EST AS INSTRUCCIONES – Este manual le mostrará cómo utilizar su cargador en forma segura y efectiva. Por favor , lea, comprenda y siga estas instrucciones y precauciones cuidadosamente, ya que este manual contiene instrucciones operativas y de seguridad de imp ...

  • Schumacher SC-200A - page 23

    • 23 • Utilice solamente accesorios recomendados. El uso de un 1.3 accesorio no recomendado o suministrado por Schumacher ® Electric Corporation puede provocar riesgo de incendio, descarga eléctrica o lesiones a personas o daño a la propiedad. Para reducir el riesgo de daños al enchufe o cable eléctrico, jale 1.4 del enchufe en lugar de ja ...

  • Schumacher SC-200A - page 24

    • 24 • RIESGO DE GASES EXPLOSIVOS. RESUL T A PELIGROSO TRABAJAR EN FORMA 1.10 CERCANA A UNA BA TERÍA DE PLOMO. LAS BA TERÍAS GENERAN GASES EXPLOSIVOS DURANTE SU NORMAL FUNCIONAMIENTO. POR ESTE MOTIVO, RESUL T A DE SUMA IMPORT ANCIA QUE SIGA LAS INSTRUCCIONES CADA VEZ QUE UTILIZA EL CARGADOR. Para reducir el riesgo de explosión de una baterí ...

  • Schumacher SC-200A - page 25

    • 25 • NUNCA cargue una batería congelada. 2.5 NUNCA sobrecargue una batería. 2.6 Considere la idea de que alguna persona se encuentre cerca 2.7 suyo para poder ayudarlo cuando trabaje en forma cercana a una batería de plomo-ácido. Cuente con una gran cantidad de agua potable y jabón a mano 2.8 en caso de que el ácido de la batería tenga ...

  • Schumacher SC-200A - page 26

    • 26 • Agregue agua destilada a cada pila hasta que el ácido de la 3.4 batería alcance el nivel especicado por el fabricante de la batería. No provoque derrames. En lo que concierne a baterías que no cuentan con tapas extraíbles para pilas, tales como baterías de plomo-ácido reguladas por válvulas (VRLA, por sus siglas en inglés), s ...

  • Schumacher SC-200A - page 27

    • 27 • PRECAUCI ON ES DE CON E XI ÓN EN CC 5. Conecte y desconecte los ganchos de salida C.C. sólo después 5.1 de haber establecido todos los interruptores del cargador a la posición de “apagado” (si es aplicable) y de haber desconectado el enchufe de C.A. del tomacorriente eléctrico. Nunca permita que los ganchos tengan contacto entre ...

  • Schumacher SC-200A - page 28

    • 28 • líneas de combustible o cuerpos metálicos. Conecte a una pieza metálica de calibre grueso del marco o del bloque motor . En un vehículo con descarga a tierra por borne positivo, conecte 6.6 el gancho NEGA TIVO (NEGRO) del cargador de batería al borne NEGA TIVO (NEG, N, -) sin descarga a tierra de la batería. Conecte el gancho POSIT ...

  • Schumacher SC-200A - page 29

    • 29 • No se ubique en posición frontal a la batería al realizar la 7.5 conexión nal. Conecte el condón de alimentación del cargador de CA al 7.6 tomacorriente. Al desconectar el cargador , siempre hágalo en forma inversa al 7.7 procedimiento de conexión y realice la primera conexión tan lejos de la batería como sea posible. Una bat ...

  • Schumacher SC-200A - page 30

    • 30 • CAR ACTE RÍ ST ICAS 9. Selector de Amperaje y V oltaje 1. Luces LED para vericar condición de la Batería 2. Cable para ensamble con pinzas para Batería. 3. Cable para ensamble con terminal de anillo 4. Cable para ensamble con enchufe de 12V 5. 1 2 3 4 5 IN STRUCC ION ES DE M ONT AJ E 10. Desenrede todos los cordones y extienda los ...

  • Schumacher SC-200A - page 31

    • 31 • Selector de voltaje Útilice este selector de voltaje para elegir la salida de voltaje de entre 6 y 12 volts para igualar la batería a cargar . IN STRUCC ION ES DE O PER ACI ÓN 1 2. Este cargador de baterías debe ser ensamblado correctamente de acuerdo a las instrucciones de ensamble antes de usar . El cargador carece de interruptor p ...

  • Schumacher SC-200A - page 32

    • 32 • NOT A: Nunca conecte la pinza y las terminales de los conectores de argolla juntos, para aplicarlo de otra forma, tal como batería externa u otra fuente de poder de carga, o para alargar el cable de salida, esto ocasionará polaridad invertida o sobrecarga. Pinzas De Bateria De 50 Amps Conecte la punta del cable de salida del cargador a ...

  • Schumacher SC-200A - page 33

    • 33 • Dirija el cable de corriente del cargador por la ventana abierta 3. del vehículo. Conecte el cable del cargador a un tomacorriente de pared 4. de 120 V olts de CA. Asegúrese de colocar el cargador en una supercie seca, no ammable como metal o concreto. Indicador de conexión de la batería Si el cargador no detecta una batería c ...

  • Schumacher SC-200A - page 34

    • 34 • la batería totalmente cargada mediante una pequeña corriente cuando corresponda. Si el cargador tiene que funcionar al máximo en corriente continua de mantenimiento a un periodo de 12 horas, se transladará al Modo de Interrumpir (véase la sección Carga Interrumpida). Esto es ocacionalmente causado por una pérdida de energía en la ...

  • Schumacher SC-200A - page 35

    • 35 • Batería de 2 amperios, 12 voltios Condición de la batería Capacidad de la batería en amperios/horas T iempo de carga promedio aproximado en horas Descargada al 50% Descargada al 100% 10 3.2 6.2 12 4.0 7.5 20 6.4 12.4 Batería de 4 amperios, 6 voltios Condición de la batería Capacidad de la batería en amperios/horas T iempo de carg ...

  • Schumacher SC-200A - page 36

    • 36 • Cualquier otro servicio debe realizarse por personal calicado en 14.5 el ramo. IN STRUCC ION ES P AR A E L MA NEJ O Y ALM ACENA MI ENTO 15. Gua rde el carg ado r d esen chu fado en po sici ón ver tica l. El c abl e 15.1 se guir á co nd uc ie nd o el ec tr ic id ad h as ta q ue s e de se nc hu fe d el t om a. Almacene en el interior ...

  • Schumacher SC-200A - page 37

    • 37 • PROBLEMA POSIBLE CAUSA SOLUCIÓN Se escucha un sonido seco en el cargador (“clic”). (continuado) Cables o ganchos de la batería en cortocircuito. Buena batería pero extremadamente descargada. Conexiones inversas en la batería. El disyuntor se resetea cuando el consumo de corriente es demasiado elevado. Controle la posible presenci ...

  • Schumacher SC-200A - page 38

    • 38 • PROBLEMA POSIBLE CAUSA SOLUCIÓN LED VERIFICACIÓN (rojo) encendido. Los ganchos no se encuentran bien conectados a la batería. Conexiones inversas. Batería defectuosa (no acepta una carga). V erique la posible presencia de una conexión defectuosa a la batería o al bastidor . Asegúrese de que los puntos de conexión estén limpio ...

  • Schumacher SC-200A - page 39

    • 39 • PROBLEMA POSIBLE CAUSA SOLUCIÓN El cargador no se enciende incluso al estar bien conectado. (continuado) Conexión eléctrica deciente. El voltaje de la batería es muy bajo. Batería defectuosa. Controle la posible pérdida del enchufe perteneciente a los cables de alimentación o al alargador . Este cargador tiene un dispositivo de ...

  • Schumacher SC-200A - page 40

    • 40 • Si las soluciones descriptas no eliminan el problema o por información sobre la solución de problemas, puede llamar a la línea gratuita desde cualquier lugar de los EE.UU. 1-800-621-5485 7:00 a. m. a 5:00 p. m. hora central de lunes a viernes GA R ANT ÍA LI MI T A DA 18. GARANTIA LIMIT ADA NO V ALIDA EN MEXICO. SCHUMACHER ELECTRIC CO ...

  • Schumacher SC-200A - page 41

    • 41 • personas asocia das al producto, incluidas, a títu lo enunciativo, los ingresos y ganancias no percibidos, ventas anticipadas, oportunidades c omerciales, el bu en nombre, la int errupción de la actividad comer cial o cualquier otro daño que hay a provocado. T odas las garantías, excepto la garant ía limitada inclu ida en el present ...

Produzent Schumacher Kategorie Automobile Battery Charger

Dokumente, die wir vom Produzenten des Geräts Schumacher SC-200A erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Schumacher
- Bedienungsanleitungen SC-200A
- Produktkarten Schumacher
- Informationsbroschüren
- oder Energieetiketten Schumacher SC-200A
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Schumacher SC-200A.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Schumacher SC-200A, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Schumacher SC-200A. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Schumacher SC-200A ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Schumacher SC-200A, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Schumacher SC-200A hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Schumacher SC-200A verständlich ist.

Eine gänzliche Bedienungsanleitung von Schumacher sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Schumacher SC-200A bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Schumacher SC-200A befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Schumacher SC-200A, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Schumacher SC-200A - die uns die ersten Schritte während der Nutzung von Schumacher SC-200A erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Schumacher SC-200A hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Schumacher SC-200A im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Schumacher SC-200A?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Schumacher SC-200A nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Schumacher SC-200A hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (1)

christiane

je cherche le code pin sur mon appareil mais je ne trouve pas comment faire