-
Magnadyne M11RF-LCD - page 1
User’ s Manual Model: M11RF-LCD T wo-Way Communication LCD T ransmitter 4/5/6 5 4 C For T echnical Assistance, please call (800) 638-3600, or visit www .magnadyne.com M11RF-LCD-UM 9/10/04 9:48 AM Page 1 ...
-
Magnadyne M11RF-LCD - page 2
The remote control is powered by a 1.5V type AAA Alkaline battery . When the power of the battery weakens the battery icon will be displayed on the LCD screen. When the old batter y is replaced with a new one, there will be a beep to indicate the power is up and the clock on the LCD screen returns to AM12:00 after displaying all the icons. Correct ...
-
Magnadyne M11RF-LCD - page 3
3 Remote Control T ransmitters Operation T ransmitter Button System Function Remark Lock Doors & Arm System Panic Function Press and Hold for 3 Seconds Car Locator Under Armed Mode Arm and Delete the 2 Stage Shock Sensor Press T wice within 3 Seconds Silent Arming/Disarming Ignition in “OFF” Position Active Anti-Car Jacking Mode Ignition in ...
-
Magnadyne M11RF-LCD - page 4
4 LCD Display T ransmitter Operations T ransmitter Button System Function Remark SET (C) Systems T rigger Record Check Press within 3 Seconds SET SET (C) System’ s Status Check Press within 3 Seconds SET Button Lock Press within 3 Seconds and Hold “Lock” Button for 2 seconds SET Optional Driving Pager Press within 3 Seconds SET Monitor Interi ...
-
Magnadyne M11RF-LCD - page 5
5 LED Display Parking Light System Characteristics Siren/Horn Parking Light LED Doors Starter Dome Light 1. Arming 1 or 3 Chirps 1 Flash Slow Flash Locking Disabled 2. Disarming 2 or 4 Chirps 2 or 3 Flashes Unlocking T urns on for 30 Seconds 3. T rigger Alarming Flashes Slow Flash Disabled Flashes 4. Passive Starter Disable Fast Flash Disabled 5. P ...
-
Magnadyne M11RF-LCD - page 6
6 Active Arming: Lock & Arm 1. Press the button on the transmitter . 2. The siren will chirp once and parking lights will flash once indicating that the system is now armed. The vehicle door will lock upon arming when interfaced with the security system. Clear the Flash Icon: Press the SET button 3 times within 3 seconds to clear the flash icon ...
-
Magnadyne M11RF-LCD - page 7
7 Active Disarming Unlock & Disarm 1. Press the button on the transmitter . 2. The siren will chirp twice and parking lights will flash twice indicating that the system is now disarmed. The vehicle door will unlock and the dome light will turn on for 30 seconds upon disarming when interfaced with the security system. Shock Sensor Triggered Igni ...
-
Magnadyne M11RF-LCD - page 8
The valet switch allows you to temporarily bypass all alarm functions eliminating the need to hand your transmitter to parking attendants or garage mechanics. When the system is in valet mode, all alarm functions and remote start functions are bypassed, however the remote panic feature and remote door locks will remain operational. T o use the vale ...
-
Magnadyne M11RF-LCD - page 9
T rigger the System (Continued) Ignition T rigger (Clear the Flash Icon and Melody Sound): When the Security System is triggered, the LCD screen will alert the user through melody sound and flashing icons. By pressing the “SET” button 3 times within 3 seconds it will clear the flashing icons and stop the melody sound. Stop the Melody Sound: Whe ...
-
Magnadyne M11RF-LCD - page 10
Anti-Car Jacking (Continued) T rigger the Anti-Car Jacking Mode Three Timer cir cuits will function as follows: First Timer Circuit 1. 50 seconds after the car jacking mode has been activated, the siren will begin to sound for 15 seconds. 2. During the 15 second activation period, you will be alerted to push the valet switch once to turn off the ca ...
-
Magnadyne M11RF-LCD - page 11
Dome Light Supervision The Security System has a unique feature for using your vehicle’ s dome light. 1 . Upon disarming the vehicles security system, the interior dome light will remain on for thirty seconds. 2. If the security system is triggered, the dome light will flash for the same duration as the horn/siren. Ignition Controlled Door Locks ...
-
Magnadyne M11RF-LCD - page 12
Remote Start Operation T o Remote Start Y our Vehicle by Using the Remote T ransmitter: 1. Press the button twice on the remote transmitter . 2. The parking lights will turn “ON” to indicate the remote start is activated. 3. The engine will start in approximately 5 seconds. 4. Once the engine is running, the parking lights will turn back on to ...
-
Magnadyne M11RF-LCD - page 13
Timer Start: This unit can be programmed to start and run the engine every 3 hours, 2 hours or punctually at the same time every morning. The engine will run for the programmed running time and then shut down. Important! Timer start should be used only in open areas. Never start, or most importantly leave a vehicle running in an enclosed area. 3 or ...
-
Magnadyne M11RF-LCD - page 14
Interference 4/5/6 5 4 C SET Bi 6 Note: The transmission range may become shorter if the system is interfered by a stronger radio frequency from sources of high voltage electric power or obstacles like tall buildings. The transmitter uses low output powered frequency . 14 T urbo Timer Mode (Also See Installation Manual) T urbo Timer Mode keeps the ...
-
Magnadyne M11RF-LCD - page 15
Door Lock Lock your Vehicles Doors Door Unlock Unlock your Vehicles Doors Armed Mode Security System is Armed Valet Mode Security System is Armed Remote T ransmission T ransmitting a Signal In-Range Indicator Y ou are within Remote Range Door T riggered Doors are Opened T runk/Hood T riggered T runk/Hood are Open Shock Sensor Shock Sensor T riggere ...
-
Magnadyne M11RF-LCD - page 16
16 Screen Lamp On: Press and hold the “SET” button one second, with the melody sound and the LCD screen lamp will turn on for 5 seconds. Power Save Mode: While in the Power Save Mode, the LCD transmitter uses “0” current to save the battery power . 1. Press and hold the “SET” button for 5 seconds. One melody will sound from the transmit ...
-
Magnadyne M11RF-LCD - page 17
Vibration/Melody Mode: This mode is useful when you are in a noisy place and it is difficult to hear the beep from the remote. The LCD transmitter will vibrate if your security system has been activated. Press the “SET” button first, within 3 seconds press the ( ) button for 2 seconds to select the mode of vibrate/melody . The icon will be disp ...
-
Magnadyne M11RF-LCD - page 18
18 Replacement Parts and Accessories 4/5/6 5 4 C 5-Button Transmitter for M11a Security System. M11RF-LCD 139.95 ea. 4-Button Transmitter with SAW Technology for M11RF 59.95 ea. M11a Security System. TRANSMITTERS DESCRIPTION MODEL # $ PRICE BATTERIES 1.5 Volt AAA Alkaline Battery commonly found in grocery stores, hardware stores, etc. CR2025 - 3 Vo ...
-
Magnadyne M11RF-LCD - page 19
Credit Card or Money Order Only (Sorry No Cash, C.O.D. or personal checks accepted) SHIP TO: (No P .O. Boxes) LAST NAME FIRST NAME INITIAL STREET ADDRESS ADDITIONAL ADDRESS ADDITIONAL ADDRESS CITY ST A TE ZIP CODE DA Y TIME PHONE NUMBER PAR T # DESCRIPTION QTY . PRICE EACH TOT AL Sales Subtotal = ________ . ______ California Residents Add Sales T a ...
-
Magnadyne M11RF-LCD - page 20
M11RF-LCD-UM 2-10-04 Rev. A © Copyright 2004 Magnadyne Corporation Limited Lifetime Warranty Magnadyne Corporation or its authorized agents will, for the life of the vehicle and to the original purchaser , repair , replace or refund the retail sales price of said product or any part thereof, at the option of the Magnadyne Corporation or its author ...
Haben Sie eine Frage bezüglich Magnadyne M11RF-LCD?
Nutzen Sie das untere Formular
Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Magnadyne M11RF-LCD nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Magnadyne M11RF-LCD hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.