-
La Crosse Technology WS-9014U - page 1
1 WS-9014U Wireless 433 MHz Temperature Station Instruction Manual ...
-
La Crosse Technology WS-9014U - page 2
2 TABLE OF CONTENTS Topic Page Inventory of Contents 3 Quick Setup 4-8 Detailed Setup Guide Battery Installation 9-10 Setting the Time 11-12 Selecting Units of Measurement 12-13 Features Minimum and Maximum Temperatures 13 Resetting Minimum and Maximum Temperatures 14 Additional remote temperature sensors (optional) 14-17 Mounting 17-18 Troubleshoo ...
-
La Crosse Technology WS-9014U - page 3
3 INVENTORY OF CONTENTS 1. The indoor temperature station (Figure 1) 2. The remote temperature sensor (TX6U) and mounting bracket. (Figure 2) 3. 3 each, 1/2” Philips screws. 4. One strip of double sided adhesive tape. 5. Instruction Manual and Warranty Card. ADDITIONAL EQUIPMENT (not included) 1. 1 Philips screwdriver. 2. 2 Fresh AA 1.5V batterie ...
-
La Crosse Technology WS-9014U - page 4
4 QUICK SETUP Hint: Use good quality Alkaline Batteries and avoid rechargeable batteries. 1. Have the indoor temperature station and remote temperature sensor 3 to 5 feet apart. 2. Batteries shoul d be out of both units for 10 m inutes. 3. Place the batteries into the remote temperature sensor first then into the indoor temperat ure station. (All r ...
-
La Crosse Technology WS-9014U - page 5
5 In this time the indoor temperature station and rem ote tem perature sensor will start to talk to each other and the display will show both the indoor temperature and an out door temperat ure. If the indoor tem perature station does not display bot h temperat ures after the 10 minutes pl ease retry the set up as stated above. After both i ndoor a ...
-
La Crosse Technology WS-9014U - page 6
6 of resistance. Your distance plus resistance should not exceed 80 ft. in a straight line. NOTE: Fog and mist will not harm your remote t emperature sensor but direct rain must be avoided. To complet e the set up of your indoor temperature station after the 10 minutes have passed please follow the steps below. 1. Press and hold the “SET” butto ...
-
La Crosse Technology WS-9014U - page 7
7 b. When you have your choice shown on the display press and release the “SET” button once. 2. Degree Fahrenh eit will now sho w . a. To change between Fahrenheit and Celsius, press and release the “MIN/MAX” button. b. When you have your choice shown on the display press and release the “SET” button once. 3. An hour w ill n o w be flas ...
-
La Crosse Technology WS-9014U - page 8
8 PM hours. During the AM hours this area will be blank. b. When the correct hour is shown, press and release the “SET” button once. 4. A minute will now be flashin g . a. Press and release the “MIN/MAX” button u ntil the correct minutes are displayed. Press and release the SET button once more and you are done. DETAILED SETUP GUIDE I. BATT ...
-
La Crosse Technology WS-9014U - page 9
9 1. Remove the mounting bracket. 2. Remove battery cover 3. Observing the correct polarity, install 2 AA batteries—make sure they do not spring free, or start-up problems may occur. Replace cover. B. INDOOR TEMPERATURE STATION Note: After the batteries are installed, DO NOT press any buttons. This may interfere with the signals, causing temperat ...
-
La Crosse Technology WS-9014U - page 10
10 1. Remove the battery cover on the backside. To do this, push up and pull out. 2. Observing the correct polarity, install 2 AA batteries. 3. Replace battery cover. 4. Wait 10 minutes or until both the indoor and outdoor temperatures are shown on the indoor temperature station. 5. The indoor temperature station should now show: “-:- - ” in th ...
-
La Crosse Technology WS-9014U - page 11
11 II. TIME A. SETTING THE TIME 1. Press and hold the “ SET” button for 5 second, “12h” will appear in the TIME LCD. 2. Press and release the “ MIN/MAX” button to select either 12h time (am/pm) or 24h time 3. Press and release the “ SET” button 2 times, the hour will flash in the upper left corner. 4. Press and release the “ MIN/M ...
-
La Crosse Technology WS-9014U - page 12
12 Note: When in 12h mode, there is only a “PM” display, which appears under “TIME.” If there is no display here it is AM. Make sure you set the time accordingly. III. UNITS OF TEMPERATURE MEASURE A. SELECTING UNITS OF MEASUREMENT 1. Press and hold the “SET” button for 5 second until “12h” or “24h” appears in the TIME LCD. 2. Pr ...
-
La Crosse Technology WS-9014U - page 13
13 IV. FEATURES A. MINIMUM AND MAX IMUM TEMPERATURES 1. Press and release the “ MIN/MAX” button, “MIN” appears in the temperature LCD’s and the recorded minimum temperat ure s a re display ed. 2. Press and release the “ MIN/MAX” button to toggle to the maximum temperatures. The time of occurrence of the value for outdoor temperature w ...
-
La Crosse Technology WS-9014U - page 14
14 1. The WS-9014U is able to receive signals from 3 different remote temperature sensors. Following are some brief instructions for the basic set-up of remote temperature sensor units with the WS-9014U. These extra sensors can be purchased through the same dealer as this unit, or by contacting La Crosse Technology directly. A TX6 will monitor temp ...
-
La Crosse Technology WS-9014U - page 15
15 the total time for set-up exceeds 6 minutes. 2. It is necessary to remove the batteries from all units currently in operation. 3. Remove the battery covers to all remote temperature sensor units. 4. Place all remote temperature sens or units in a numeric sequential order. 5. In sequential order, install batteries (follow the same battery install ...
-
La Crosse Technology WS-9014U - page 16
16 from one “boxed” number to the next should be observed in the OUTDOOR LCD. 2. To view the Mi ni mum/ Ma xi mum temperature: first select from which remote temperature sensor to read data (indicated by the “boxed” number). Pressing and releasing the “MIN/MAX” button will toggle through the minimum and maximum indoor temperature, and t ...
-
La Crosse Technology WS-9014U - page 17
17 both units in their desired location before permanently mounting. A. REMOTE TEMPERATURE SENSOR 1. Remove the mounting bracket from the remote temperature sensor 2. Mount using either screws or adhesive tape. 3. Reattach the remote temperature sensor to the mounting bracket. B. THE TEMPERATURE STATION 1. The indoor temperature station comes with ...
-
La Crosse Technology WS-9014U - page 18
18 temperature station onto the screw using the hanging hole on the backside. Gently pull the indoor temperature station down to lock the screw into place. TROUBLESHOOTING NOTE: For problems not solved, please contact La Crosse Technology via e-mail or phone, or visit our website, www.lacrossetechnology.com Problem: The LCD is faint Solution: Repla ...
-
La Crosse Technology WS-9014U - page 19
19 4) Place remote temperature sensor and indoor temperature station in position so the straight-line signal is not passing through more than two or three walls. Problem: Temperatures do not match if units are placed next to each other. Solution: Each temperature sensor is manufactured to be accurate to within 1 degree plus or minus and under norma ...
-
La Crosse Technology WS-9014U - page 20
20 ends of a range, making it harder to compare different ranges with different curves. Under non-laboratory conditions, it is difficult to compensate for the above factors and obtain an accurate comparison. MAINTENANCE AND CARE INSTRUCTIONS • Extreme temperatures, vibration, and shock should be avoided to prevent damage to the units. • Clean d ...
-
La Crosse Technology WS-9014U - page 21
21 SPECIFICATIONS Transmitting Frequency 433MHz Measuring Temperatures Indoor Temperature Station: Indoor 32 ° F to 156.2 ° F with 0.2 ° F resolution. (0 ° C to 69.0 ° C with 0.1 ° C resolution) Indoor Temperature Station: Outdoor -21.8 ° F to 156.2 ° F with 0.2 ° F resolution. (-29.9 ° C to 69.0 ° C with 0.1 ° C resolution) Temp accura ...
-
La Crosse Technology WS-9014U - page 22
22 Indoor Temperature Station 2 x AAA, 1.5V Dimensions: (L x W x H) Indoor Temperature Station 2.36 x 0.88 x 5.90 in. Remote Temperature Sensor 1.57 x 0.85 x 5.00 in. Battery life Approximately 1 year WARRANTY INFORMATION La Crosse Technology provides a 1-year warr anty on this weather station. Contact La Crosse Technology im mediately upon discove ...
-
La Crosse Technology WS-9014U - page 23
23 This warranty does not cover any defects r esulting from im proper use, unauthorized repair s, faulty batteries, or the weather stations inability to receive a signal due to any source of interference. LA CROSSE TECHNOLOGY WILL NOT ASSUME LIABILITY FOR INCIDENTAL, CONSEQUENTIAL, PUNITIVE, OR OTHER SIMILAR DAMAGES ASSOCIATED WITH THE OPERATION OR ...
-
La Crosse Technology WS-9014U - page 24
24 Phone: 608.782.1610 Fax: 608.796.1020 e-mail: support@lacrossetechnology.com (warranty work) sales@lacrossetechnology.com (information on other products) web: www.lacross ete chnology.com FCC DISCLAIMER This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful ...
-
La Crosse Technology WS-9014U - page 25
25 FCC ID: OMO-01RX (Receiver), OMO-01TX (tr ansm itter) THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: 1. THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND 2. THIS DEVICE MUST ACCEPT INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. ...
Haben Sie eine Frage bezüglich La Crosse Technology WS-9014U?
Nutzen Sie das untere Formular
Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit La Crosse Technology WS-9014U nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit La Crosse Technology WS-9014U hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.