Bedienungsanleitung Cisco Systems 69561

18 Seiten 0.03 mb
Download

Zur Seite of 18

Summary
  • Cisco Systems 69561 - page 1

    Wireless LAN Controller (WLC) FAQ Document ID: 69561 Questions Introduction General FAQ Troubleshoot FAQ NetPro Discussion Forums − Featured Conversations Related Information Introduction This document provides information on the most frequently asked questions (FAQ) about the Cisco Wireless LAN (WLAN) Controllers (WLCs). Refer to Cisco Technical ...

  • Cisco Systems 69561 - page 2

    Bootloader Version............................... 4.0.217.0 Build Type....................................... DATA + WPS Compact Flash Size............................... 256 MB In order to view the active boot image, use the command show boot (Cisco Controller) > show boot Primary Boot Image............................... 4.0.217.0 (active) Bac ...

  • Cisco Systems 69561 - page 3

    You must reboot the WLC in order for the new software to take effect, so there is a period of network downtime. Be sure to schedule a maintenance window for the upgrade. Q. Can a Cisco IOS Software−based access point (AP) that has been converted to lightweight mode register with Cisco 4100 Series WLCs? A. No, Cisco IOS Software−based APs that a ...

  • Cisco Systems 69561 - page 4

    mobility group. You can configure up to 12 Wireless Services Module (WiSM) blades in one mobility group. Therefore, up to a maximum of 3600 access points (APs) are supported in a single mobility group. Q. How does DHCP work with the WLC? A. The WLC acts as a DHCP relay device. The WLC does the DHCP relay through the virtual interface. Typically, th ...

  • Cisco Systems 69561 - page 5

    From the Wireless Downloads page, click on Wireless LAN Controller and select the controller platform for which you need the MIBs. 1. The Software Download page for the controller appears. This page contains all the files for the WLC including the MIBs. 2. Download the standard MIBs and the Cisco specific MIBs. These two files should be downloaded ...

  • Cisco Systems 69561 - page 6

    Q. Which lightweight access points (LAPs) do the 4100 Series Controllers support? A. Only the Airespace 1200, 1250, the Cisco 1000 Series, and the Cisco 1500 Series LAPs work with the earlier 4100 Series Controllers. Q. I have a Cisco Adaptive Security Appliance (ASA) device. Can I use this ASA as a DHCP server instead of windows DHCP server in ord ...

  • Cisco Systems 69561 - page 7

    A. This is due to Cisco bug ID CSCsh58468 ( registered customers only ) . As of the latest controller version 4.0.206.0, a user can enter only 31 characters. Currently, there is no workaround for this. Q. With the Management via Wireless feature enabled on wireless LAN controllers (WLCs) in a mobility group, I can only access one WLC from that mobi ...

  • Cisco Systems 69561 - page 8

    Enable broadcast service set identifier (SSID) per WLANWith broadcast SSID enabled, the WLAN/SSID information is sent in the beacons. This also helps clients that perform passive scanning (those that do not transmit probe request) as well as clients configured without an SSID to associate with the controller through this WLAN. ♦ Disable Airone ...

  • Cisco Systems 69561 - page 9

    Q. Can the Wireless LAN Controller (WLC) send email notifications to the administrator when a critical event occurs? A. The WLC does not send email, but it can send traps to the Network Management System (NMS) stations, such as HP OpenView (HPOV). HPOV can perform things such as running scripts to send email on receipt of particular traps. HPOV is ...

  • Cisco Systems 69561 - page 10

    configuration to the backup controller off the production network. After the configuration is copied to the backup controller, you need to change the hostname, IP addressing information, RADIUS shared secret keys (possibly) and Mobility group lists information. Change the mobility group member, which one is listed as <Local>. 3. Transfer this ...

  • Cisco Systems 69561 - page 11

    Q. Is it possible to set a limit to the number of clients that connect to the access point (AP) on the AP itself? A. In general, there is no way on the AP to limit the number of clients that connect. The clients actually load balance between APs once they exceed the profile threshold value, which by default is 12 users. If you enable aggressive loa ...

  • Cisco Systems 69561 - page 12

    (WLCM) or Wireless Services Module (WiSM), you should be able to access the controller from the WCS and create a new admin user without logging into the controller itself. Or, if you did not save the configuration on the controller after you deleted the user, then a reboot (power cycling) of the controller should bring it back up with the deleted u ...

  • Cisco Systems 69561 - page 13

    Bridge AP to Normal AP. Q. I recently set up the 4402 Wireless LAN Controller (WLC) to manage the new Cisco lightweight access points (LAPs). I run PIX 501 version 6.3(5) and also use the PIX as a DHCP server for the clients. However, whenever the PIX gets a request from the controller for the wireless clients, it drops the request and the clients ...

  • Cisco Systems 69561 - page 14

    Q. Does the Cisco Unified Wireless solution support redundant WLCs in the DMZ for guest tunneling? A. Presently there is no support for redundant WLCs in the DMZ for guest tunneling. This is why the client does not automatically connect to the other controller in the DMZ. Q. Wireless LAN Clients associated with the lightweight access points are not ...

  • Cisco Systems 69561 - page 15

    MAC address. Q. No traps are generated by the WLC for Ad−Hoc rogues and the SNMP debugs on the WLC do not show any traps from the WLC for Ad−Hoc even though the WLC GUI reported the Ad−Hoc rogues. The WLC runs firmware version 3.2.116.21. Why does this happen? A. This is due to Cisco bug ID CSCse14889 ( registered customers only ) . The WLC c ...

  • Cisco Systems 69561 - page 16

    AP1 can hear the client that communicates to AP2, but AP2 cannot be heard. Therefore, it cannot be validated as a neighbor. ♦ The workaround is to manually set the APs to known internal on the WLC and/or WCS. Complete these steps on the controller in order to manually set the APs to known internal: Go to the WLC GUI and choose Wireless . 1. Click ...

  • Cisco Systems 69561 - page 17

    This command will replace the 1.1.1.1 virtual interface address, which shows up itself as the DHCP server, with the actual DHCP server IP address that you defined on the interface or in the override option of the WLAN. Q. We have a couple of Access Control Servers (ACS) that authenticate the wireless clients associated to wireless LAN controllers ( ...

  • Cisco Systems 69561 - page 18

    Wireless − Mobility: WLAN Radio Standards Wireless − Mobility: Security and Network Management Wireless − Mobility: Getting Started with Wireless Wireless − Mobility: General Related Information Cisco Wireless LAN Controller Module Q&A • Cisco Wireless LAN Controllers Q&A • Cisco Wireless LAN Controller Configuration Guide, Rele ...

Produzent Cisco Systems Kategorie Network Router

Dokumente, die wir vom Produzenten des Geräts Cisco Systems 69561 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Cisco Systems
- Bedienungsanleitungen 69561
- Produktkarten Cisco Systems
- Informationsbroschüren
- oder Energieetiketten Cisco Systems 69561
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Cisco Systems 69561.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Cisco Systems 69561, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Cisco Systems 69561. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Cisco Systems 69561 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Cisco Systems 69561, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Cisco Systems 69561 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Cisco Systems 69561 verständlich ist.

Eine gänzliche Bedienungsanleitung von Cisco Systems sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Cisco Systems 69561 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Cisco Systems 69561 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Cisco Systems 69561, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Cisco Systems 69561 - die uns die ersten Schritte während der Nutzung von Cisco Systems 69561 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Cisco Systems 69561 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Cisco Systems 69561 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Cisco Systems 69561?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Cisco Systems 69561 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Cisco Systems 69561 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)