Bedienungsanleitung Pelco C1306M

24 Seiten 1.04 mb
Download

Zur Seite of 24

Summary
  • Pelco C1306M - page 1

    ExSite ™ EHXM Series Explosionproof Fixed System INSTALLATION C1306M (8/05) ...

  • Pelco C1306M - page 2

    2 C1306M (8/05) Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Pelco C1306M - page 3

    C1306M (8/05) 3 Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not block any ventilation openings. Install in accordance with the manufacturer’ s instructions. 6. T o reduce the risk of ignition of hazardous atmospheres, disconnect the equipment from th ...

  • Pelco C1306M - page 4

    4 C1306M (8/05) Getting Started Thank you for purchasing Pelco’ s ExSite ™ EHXM Series explosionproof system. This manual includes instructions for installing all the components of the system. Once the system installation is complete, refer to the operation/programming manual for instructions on how to operate and pro- gram your system. METHODS ...

  • Pelco C1306M - page 5

    C1306M (8/05) 5 Install the Power Module Attach the power module to the mounting surface. Use only installation methods and materials capable of supporting four times the maximum specified load of the system (140 lb/63.5 kg). NOTE: If required, install the optional TXB translator , fiber module, or UTP board before installing the power module. Re ...

  • Pelco C1306M - page 6

    6 C1306M (8/05) CONNECT WIRING Refer to the following information to connect the wires and cables as required. NOTES: • Relay 3 is allocated specifically for an external washer (not supplied by Pelco). • All relays are specified for 32 VDC, 0.5 A. • Wiring/cable for UTP and fiber optic are not provided on the wire harness. The installer mu ...

  • Pelco C1306M - page 7

    C1306M (8/05) 7 DIP SWITCH SETTINGS Configure the receiver address, termination, and baud setting for the system. The DIP switches to configure these settings are located on the top of the power module. NOTE: No DIP switch settings are required for Coaxitron control. Figure 3 shows the default settings for the DIP switches. Refer to the following ...

  • Pelco C1306M - page 8

    8 C1306M (8/05) ADDRESS SWITCH SETTING SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 1 OFF OFF OFF OFF OFF OFF OFF OFF 2 ON OFF OFF OFF OFF OFF OFF OFF 3 OFF ON OFF OFF OFF OFF OFF OFF 4 ON ON OFF OFF OFF OFF OFF OFF 5 OFF OFF ON OFF OFF OFF OFF OFF 6 ON OFF ON OFF OFF OFF OFF OFF 7 OFF ON ON OFF OFF OFF OFF OFF 8 ON ON ON OFF OFF OFF OFF OFF 9 O ...

  • Pelco C1306M - page 9

    C1306M (8/05) 9 ADDRESS SWITCH SETTING SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 49 ON OFF OFF OFF ON ON OFF OFF 50 OFF ON OFF OFF ON ON OFF OFF 51 ON ON OFF OFF ON ON OFF OFF 52 OFF OFF ON OFF ON ON OFF OFF 53 ON OFF ON OFF ON ON OFF OFF 54 OFF ON ON OFF ON ON OFF OFF 55 ON ON ON OFF ON ON OFF OFF 56 OFF OFF OFF ON ON ON OFF OFF 57 ON OFF OF ...

  • Pelco C1306M - page 10

    10 C1306M (8/05) T able B. D Protocol Receiver Address (Continued) ADDRESS SWITCH SETTING SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 143 ON ON ON ON OFF OFF OFF ON 144 OFF OFF OFF OFF ON OFF OFF ON 145 ON OFF OFF OFF ON OFF OFF ON 146 OFF ON OFF OFF ON OFF OFF ON 147 ON ON OFF OFF ON OFF OFF ON 148 OFF OFF ON OFF ON OFF OFF ON 149 ON OFF ON OF ...

  • Pelco C1306M - page 11

    C1306M (8/05) 11 ADDRESS SWITCH SETTING SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 239 ON ON ON ON OFF ON ON ON 240 OFF OFF OFF OFF ON ON ON ON 241 ON OFF OFF OFF ON ON ON ON 242 OFF ON OFF OFF ON ON ON ON 243 ON ON OFF OFF ON ON ON ON 244 OFF OFF ON OFF ON ON ON ON 245 ON OFF ON OFF ON ON ON ON 246 OFF ON ON OFF ON ON ON ON ADDRESS SWITCH SET ...

  • Pelco C1306M - page 12

    12 C1306M (8/05) Install the Camera Module To install the camera module, do the following: 1. Refer to Figure 4. Loosen the set screw at the back of the camera enclosure with the provided 1.5 mm Allen wrench. Figure 4. Loosen Set Screw 2. Use the supplied spanner wrench to loosen the back of the camera enclosure (refer to Figure 5). Once the back i ...

  • Pelco C1306M - page 13

    C1306M (8/05) 13 3. Slide the camera module into the camera enclosure. Refer to Figure 6 to position the camera module properly in the camera enclosure. Carefully mate the camera’ s power connector to the mating connector located inside the camera enclosure. Models with a wiper: The tab located inside the camera enclosure must be pointing down be ...

  • Pelco C1306M - page 14

    14 C1306M (8/05) 4. Models with a wiper: Refer to Figure 8 and do the following to install the arm of the wiper: a. Place the supplied green bushing on the stud located behind the handle of the camera module. The bushing should be in the same orientation as shown in Figure 8. b. Install the wiper arm. Place the ridge of the arm in the notch of the ...

  • Pelco C1306M - page 15

    C1306M (8/05) 15 Install the Enclosure and Set Pan Position 1. Lightly apply O-ring lubricant (supplied) to the O-ring, and then install the O-ring on the rim of the power module (refer to Figure 9). Figure 9. Lightly Lubricate and Install O-Ring 2. Refer to Figure 10 and attach the enclosure unit to the power module. Align the pins of the enclosur ...

  • Pelco C1306M - page 16

    16 C1306M (8/05) Set the T ilt Angle of the Camera Module 1. Place a 41 mm open end or crescent wrench on the tilt locking nut and a 21 mm open end wrench on the tilt shaft (refer to Figure 11). Figure 11. Set the T ilt Position 2. Hold the tilt shaft in position with the 21 mm wrench, and then turn the 41 mm wrench to loosen the tilt locking nut. ...

  • Pelco C1306M - page 17

    C1306M (8/05) 17 Install the Sun Shroud 1. Place the supplied nylon washers on the 6-32 Phillips pan head screws. Refer to Figure 12. 2. Align the mounting holes of the sun shroud with the holes on top of the camera enclosure. 3. Use the supplied nylon washers and screws to secure the sun shroud to the camera enclosure. Figure 12. Install the Sun S ...

  • Pelco C1306M - page 18

    18 C1306M (8/05) Maintenance CAMERA MODULE REPLACEMENT To replace the camera module, do the following: 1. Remove the back cap of the camera enclosure. Refer to Figure 13 and do the following: a. Loosen the set screw with a 1.5 mm Allen wrench. b. Use the supplied spanner wrench to loosen the back cap of the camera enclosure. Once the back is loose, ...

  • Pelco C1306M - page 19

    C1306M (8/05) 19 3. Models with a wiper: Remove the wiper arm and the green bushing from the unit (refer to Figure 14). 4. Slide the camera module out of the enclosure. 5. Install the new camera module by doing the following: Slide the camera module into the camera enclosure. Refer to Figure 15 to position the camera module properly in the camera e ...

  • Pelco C1306M - page 20

    20 C1306M (8/05) 6. Models with a wiper: Refer to Figure 14 and do the following to reinstall the arm of the wiper: a. Reinstall the green bushing on the stud located behind the handle of the camera module. b. Reinstall the wiper arm. Place the ridge of the arm in the notch of the camera enclosure tab and the slot of the arm over the green bushing. ...

  • Pelco C1306M - page 21

    C1306M (8/05) 21 Specifications ELECTRICAL Input V oltage 24 V AC or 100-240 VAC Input V oltage Range ±10% Power Consumption Maximum 60 watts (120 V A) per system Heater and Defroster Microprocessor controlled Electrical Connections 6-foot wire harness with connections for power , video, data control, alarm inputs, and auxiliary outputs MECHANICA ...

  • Pelco C1306M - page 22

    22 C1306M (8/05) *Manual control of camera setup functions can be done with CM6700, CM6800, CM8500, CM9500, CM9740, CM9760, CM9770, CM9780, KBD200A, KBD300A, and MPT9500 controllers, but not with CM7500, MPT9000, or KBD9000 controllers. CAMERA/OPTICS Camera Day/Night (23X) Color LowLight ™ (22X) Color Signal Format NTSC, P AL NTSC, P AL Scanning ...

  • Pelco C1306M - page 23

    PRODUCT WARRANTY AND RETURN INFORMA TION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic products. • Three years on Genex ® Series ...

  • Pelco C1306M - page 24

    W orldwide Headquarters 3500 Pelco W ay Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .pelco.com ISO 9001 United States | Canada | United Kingdom | The Netherlands | Singapore | Spain | Scandinavia | France | Middle East ...

Produzent Pelco Kategorie Plumbing Product

Dokumente, die wir vom Produzenten des Geräts Pelco C1306M erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Pelco
- Bedienungsanleitungen C1306M
- Produktkarten Pelco
- Informationsbroschüren
- oder Energieetiketten Pelco C1306M
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Pelco C1306M.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Pelco C1306M, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Pelco C1306M. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Pelco C1306M ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Pelco C1306M, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Pelco C1306M hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Pelco C1306M verständlich ist.

Eine gänzliche Bedienungsanleitung von Pelco sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Pelco C1306M bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Pelco C1306M befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Pelco C1306M, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Pelco C1306M - die uns die ersten Schritte während der Nutzung von Pelco C1306M erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Pelco C1306M hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Pelco C1306M im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Pelco C1306M?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Pelco C1306M nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Pelco C1306M hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)