Bedienungsanleitung Delta (Model 31-300)

24 Seiten 1.98 mb
Download

Zur Seite of 24

Summary
  • Delta (Model 31-300) - page 1

    INSTRUCTION MANUAL P ART NO. 913131 - 04-12-05 Copyright © 2005 Delta Machinery T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582). Sanding Center 6" Belt/12" Disc Sander (Model 31-300) ...

  • Delta (Model 31-300) - page 2

    2 T ABLE OF CONTENTS Read and understand all warnings and operating instructions before using any tool or equipment. When using tools or equipment, basic safety precautions should always be followed to r educe the risk of personal injury . Improper operation, maintenance or modification of tools or equipment could r esult in serious injury and prop ...

  • Delta (Model 31-300) - page 3

    3 Indicates an imminently hazardous situation which, if not avoided, will r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, could r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, may r esult in minor or moderate injury . Used without the saf ...

  • Delta (Model 31-300) - page 4

    4 GENERAL SAFETY RULES READ AND UNDERST AND ALL W ARNINGS AND OPERA TING INSTRUCTIONS BEFORE USING THIS EQUIPMENT . Failure to follow all instructions listed below , may result in electric shock, fire, and/or serious personal injury or pr operty damage. IMPORT ANT SAFETY INSTRUCTIONS 1. FOR YOUR OWN SAFETY , READ THE INSTRUCTION MANUAL BEFORE OPERA ...

  • Delta (Model 31-300) - page 5

    5 F AILURE TO FOLLOW THESE RULES MA Y RESUL T IN SERIOUS PERSONAL INJUR Y . ADDITIONAL SPECIFIC SAFETY RULES SA VE THESE INSTRUCTIONS. Refer to them often and use them to instruct others. 1. DO NOT OPERA TE THIS MACHINE until it is completely assembled and installed according to the instructions. A machine incorrectly assembled can cause serious in ...

  • Delta (Model 31-300) - page 6

    6 A separate electrical circuit should be used for your machines. This cir cuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cor d is used, use only 3-wire extension cor ds which have 3- prong gr ounding type plugs and matching receptacle which will accept the machine’ s plug. Before connec ...

  • Delta (Model 31-300) - page 7

    7 3. 240 VOL T SINGLE PHASE OPERA TION The motor supplied with your saw is a dual voltage, 120/240 volt motor . It is set at the factory at 120 volts. If it is desired to operate your machine at 240 volts, single phase, it is necessary to reconnect the motor leads in the motor junction box by following instructions given on the motor nameplate. MAK ...

  • Delta (Model 31-300) - page 8

    8 FOREWORD Delta Model 31-300 is an industrial/commercial duty 1-1/2 HP belt/disc sander . The induction-type, ball-bearing motor provides long-lasting, smooth performance. The Sanding Center can provide 3000 SFPM with the belt, and the disc will r evolve at 2100 RPM. FUNCTIONAL DESCRIPTION CAR TON CONTENTS 1. Disc Sander T able 2. Belt Guard 3. #1 ...

  • Delta (Model 31-300) - page 9

    9 Fig. 5 UNP ACKING AND CLEANING Carefully unpack the machine and all loose items fr om the shipping container(s). Remove the protective coating fr om all unpainted surfaces. This coating may be removed with a soft cloth moistened with kerosene (do not use acetone, gasoline or lacquer thinner for this purpose). After cleaning, cover the unpainted s ...

  • Delta (Model 31-300) - page 10

    10 A TT ACHING MACHINE TO ST AND DISCONNECT MACHINE FROM POWER SOURCE. 1. Pull the belt (A) Fig. 8 down through the smaller rectangular hole (B) in the top shelf of the stand. 2. Fasten the machine to the top shelf with four 5/16" x 1/2" bolts and lockwashers (C) Fig. 8 (three of which are shown) and four #10-32 self-tapping scr ews and w ...

  • Delta (Model 31-300) - page 11

    11 A B C Fig. 9 Fig. 10 Fig. 11 DISCONNECT MACHINE FROM POWER SOURCE. 1. Thread the disc table trunnion stud (A) Fig. 12 into the hole (B) on the side of the machine and tighten snug. 2. Place the disc table trunnion clamp (C) on the stud and insert the two pins (D) in the two holes (E). 3. Attach the washer , spring, and knob (Inset - Fig. 12) 4. ...

  • Delta (Model 31-300) - page 12

    Fig. 18 A ST AR TING AND STOPPING THE MACHINE The on-off switch (A) Fig. 16 is located on the sander base. T o tur n the sander “ON”, move the switch to the up position. T o tu rn the sander “OFF”, move the switch to the down position. Fig. 16 Fig. 17 A A 12 DISCONNECT MACHINE FROM POWER SOURCE. 1. Insert the trunnion key (A) Fig. 14 into t ...

  • Delta (Model 31-300) - page 13

    13 ADJUSTING TENSION AND TRACKING OF THE BEL T The machine is shipped without belt tension. Before operating the machine, follow these instructions for adjusting the belt for tension and tracking. 1. Loosen the two lock knobs (A) Fig. 19, and remove the top cover (B). 2. T ur n the belt tension lever (C) Fig. 20 counter -clockwise to increase the b ...

  • Delta (Model 31-300) - page 14

    14 14 After a long period of time, adjustments may be necessary to maintain the tension and tracking of the sanding belt. If the belt will not hold its tension, tighten the set screw (G) Fig. 22. If the belt will not hold its tracking, tighten the set screw (F) Fig. 22. Make only small adjustments to these screws. Over -tightening will lock the ten ...

  • Delta (Model 31-300) - page 15

    15 CHANGING POSITION OF SANDING ARM DISCONNECT MACHINE FROM POWER SOURCE. 1. The sanding arm (A) can be used in the vertical position (Fig. 31), the horizontal position (Fig. 30), or any angle in between. Loosen the lock handle (B), position the arm (A) to the desired angle, and tighten the lock handle (B). 2. The top idler pulley cover (C) Figs. 3 ...

  • Delta (Model 31-300) - page 16

    16 16 DISCONNECT MACHINE FROM POWER SOURCE Fig. 33 Fig. 32 ADJUSTING SANDING DISC T ABLE 90 DEGREES TO DISC TIL TING THE DISC SANDER T ABLE DISCONNECT MACHINE FROM POWER SOURCE. The table (A) can be tilted 45 degrees down (Fig. 34), by loosening the lock handle (B), tilting the table (A), and tightening lock handle (B). The degree of tilt is determ ...

  • Delta (Model 31-300) - page 17

    17 REPLACING SANDING BEL T T o replace the sanding belt: 1. Loosen the two lock knobs (A) Fig. 38, and remove the top cover (B). 2. Loosen the two screws (C) Fig. 39 enough to allow the back panel (D) Fig. 38 to hinge open. NOTE: The scr ew (C) cannot be removed. 3. Release the belt tension by turning the hand lever (E) Fig. 38. Slide the belt (F) ...

  • Delta (Model 31-300) - page 18

    18 Fig. 45 Fig. 44 SURF ACING OR EDGE SANDING WITH SANDING BEL T When surfacing (Fig. 44) or edge sanding (Fig. 45), place the sanding arm in the horizontal position and use the table (A) Fig. 44 and Fig. 45 to keep the workpiece in place. Hold the workpiece firmly and keep your fingers away from the sanding belt. Place the end of the workpiece aga ...

  • Delta (Model 31-300) - page 19

    19 Fig. 48 END SANDING WITH THE DISC When sanding the ends of narrow workpieces, use the sanding disc and an accessory miter gauge (A) Fig. 48. Move the work from the center to the left side (downwar d) of the sanding disc. AL WA YS SAND ON THE LEFT SIDE (DOWNWARD ROT A TION SIDE) OF THE SANDING DISC. SANDING ON THE RIGHT SIDE (UPWARD ROT A TION SI ...

  • Delta (Model 31-300) - page 20

    20 20 TROUBLESHOOTING For assistance with your machine, visit our website at www .deltamachinery .com for a list of service centers or call the DEL T A Machinery help line at 1-800-223-7278 (In Canada call 1-800-463-3582). MAINTENANCE P AR TS, SERVICE OR WARRANTY ASSIST ANCE All Delta Machines and accessories are manufactur ed to high quality stand ...

  • Delta (Model 31-300) - page 21

    21 A complete line of accessories is available from your Delta Supplier , Porter -Cable • Delta Factory Service Centers, and Delta Authorized Service Stations. Please visit our W eb Site www .deltamachinery .com for a catalog or for the name of your nearest supplier . Since accessories other than those offer ed by Delta have not been tested with ...

  • Delta (Model 31-300) - page 22

    22 NOTES ...

  • Delta (Model 31-300) - page 23

    23 NOTES ...

  • Delta (Model 31-300) - page 24

    The following are trademarks of POR TER-CABLE • DEL T A (Las siguientes son marcas registradas de POR TER-CABLE • DEL T A S.A.) (Les marques suivantes sont des marques de fabriquant de la POR TER-CABLE • DEL T A): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’ s Saw ® , Contractor’ s Saw ® , Contractor’ s Saw II™, Delta ® , DEL T ...

Produzent Delta Kategorie Sander

Dokumente, die wir vom Produzenten des Geräts Delta (Model 31-300) erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Delta
- Bedienungsanleitungen (Model 31-300)
- Produktkarten Delta
- Informationsbroschüren
- oder Energieetiketten Delta (Model 31-300)
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Delta (Model 31-300).

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Delta (Model 31-300), Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Delta (Model 31-300). Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Delta (Model 31-300) ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Delta (Model 31-300), wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Delta (Model 31-300) hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Delta (Model 31-300) verständlich ist.

Eine gänzliche Bedienungsanleitung von Delta sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Delta (Model 31-300) bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Delta (Model 31-300) befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Delta (Model 31-300), die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Delta (Model 31-300) - die uns die ersten Schritte während der Nutzung von Delta (Model 31-300) erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Delta (Model 31-300) hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Delta (Model 31-300) im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Delta (Model 31-300)?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Delta (Model 31-300) nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Delta (Model 31-300) hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)