Bedienungsanleitung Stanley Black & Decker CT06

20 Seiten 0.93 mb
Download

Zur Seite of 20

Summary
  • Stanley Black & Decker CT06 - page 1

    © 2010 Stanley Black & Decker , Inc. New Britain, CT 06053 U.S.A. 58543 7/201 1 V er . 3 S afety , O pera tiOn and M aintenance USer ManUaL CT06 1650 PSI HYDRAULIC CRIMPING T OOL ...

  • Stanley Black & Decker CT06 - page 2

    ...

  • Stanley Black & Decker CT06 - page 3

    CT06 User Manual ◄ 3 T ABLE OF CONTENTS SERVICING THE ST ANLEY HYDRAULIC CRIMPING TOOL. This manual contains safety , operation, and routine maintenance instructions. Stanley Hydraulic T ools recommends that servicing of hydraulic tools, other than routine maintenance, must be performed by an authorized and certied dealer . Please read the fol ...

  • Stanley Black & Decker CT06 - page 4

    4 ► CT06 User Manual SAFETY SYMBOLS Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULA TIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel. Safety symbols and signal words, as shown below , are ...

  • Stanley Black & Decker CT06 - page 5

    CT06 User Manual ◄ 5 SAFETY PRECA UTIONS T ool operators and maintenance personnel must always comply with the safety precautions given in this manual and on the stickers and tags attached to the tool and hose. These safety precautions are given for your safety . Re- view them carefully before operating the tool and before performing general main ...

  • Stanley Black & Decker CT06 - page 6

    6 ► CT06 User Manual T OOL STICKER & T AGS SAFETY T AG P/N 15875 (Shown smaller then actual size) DANGER DANGER READ OPERA TION MANUAL AND SAFETY INSTRUCTIONS FOR THIS TOOL BEFORE USING IT . USE ONL Y P ARTS AND REP AIR PROCEDURES APPROVED BY ST ANLEY AND DESCRIBED IN THE OPERA TION MANUAL. T AG TO BE REMOVED ONL Y BY TOOL OPERA TOR. SEE OTHE ...

  • Stanley Black & Decker CT06 - page 7

    CT06 User Manual ◄ 7 HOSE TYPES The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy- draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic T ools. They are: Certied non-conductive — constructed of the ...

  • Stanley Black & Decker CT06 - page 8

    8 ► CT06 User Manual HOSE RECOMMEND A TIONS Oil Flow Hose Lengths Inside Diameter USE ( Press/Return) Min. Working Pressure GPM LPM FEET METERS INCH MM PSI BAR Certied Non-Conductive Hose - Fiber Braid - for Utility Bucket T rucks 4-9 15-34 up to 10 up to 3 3/8 10 Both 2250 155 Conductive Hose - Wire Braid or Fiber Braid -DO NOT USE NEAR ELECT ...

  • Stanley Black & Decker CT06 - page 9

    CT06 User Manual ◄ 9 HTMA REQUIREMENTS TOOL CA TEGOR Y HYDRAULIC SYSTEM REQUIREMENTS TYPE I TYPE II TYPE III TYPE RR FLOW RA TE 4–6 gpm (15–23 lpm) 7–9 gpm (26–34 lpm) 1 1–13 gpm (42–49 lpm) 9–10.5 gpm (34–40 lpm) TOOL OPERA TING PRESSURE (At the power supply outlet) 2000 psi (145–155 bar) 2000 psi (138 bar) 2000 psi (138 bar) 2 ...

  • Stanley Black & Decker CT06 - page 10

    10 ► CT06 User Manual OPERA TION Open-Center (no gap) Adapter Cylinder T rigger Handle T op View of T ool Figure 2. OC/CC Setup 2. Loosen the 2 setscrews on the cylinder . 3. T urn the adapter until it stops: • Counter clockwise (CCW) to change to closed center (creates gap) • Clockwise (CW) to change to open center (clos - es gap) 4. T ighte ...

  • Stanley Black & Decker CT06 - page 11

    OPERA TION CT06 User Manual ◄ 1 1 1. If the hydraulic hoses are connected: • T urn the hydraulic system control valve OFF . • Disconnect rst the hydraulic input (supply) hose, then the output (return) hose. 2. Clean the surfaces of the die holder to remove any dirt or grease. 3. Pull the pin out to release the latch. 4. Rotate the latch aw ...

  • Stanley Black & Decker CT06 - page 12

    OPERA TION 12 ► CT06 User Manual NOTE: If the uncoupled hoses are left in the sun, pressure increase within the hoses can make them difcult to connect. Whenever possible, connect the free ends of the hoses together . TOOL RELIEF V AL VE ADJUSTMENT The relief valve on a universal pressure CT can be ad- justed to increase or decrease the tool’ ...

  • Stanley Black & Decker CT06 - page 13

    OPERA TION CT06 User Manual ◄ 13 7. Release the trigger to retract the nibs. 8. Repeat the crimp as required. 9. After the last crimp, make sure the nibs in the crimp- ing head are fully retracted 10. Pull out the latch pin and rotate the latch away from the crimping head. 1 1. Remove the tool by lifting it clear of the cable. SHUTDOWN 1. Move th ...

  • Stanley Black & Decker CT06 - page 14

    14 ► CT06 User Manual T OOL PRO TECTION & CARE • Make sure all couplers are wiped clean before con- nection. • The hydraulic circuit control valve must be in the “OFF” position when coupling or uncoupling hy- draulic tools. Failure to do so may result in damage to the quick couplers and cause overheating of the hydraulic system. • A ...

  • Stanley Black & Decker CT06 - page 15

    CT06 User Manual ◄ 15 TR OUBLESHOO TING If symptoms of poor performance develop, the following chart can be used as a guide to correct the problem. When diagnosing faults in operation of the crimping tool, always check that the hydraulic power source is supplying the correct hydraulic ow and pressure to the grinder as listed in the table. Use ...

  • Stanley Black & Decker CT06 - page 16

    16 ► CT06 User Manual SPECIFICA TIONS Capacity ................................................................................... #10-750 MCM Aluminum and #10-500 MCM Copper Crimping Force ............................................................................................. 6 tons @ 1650 psi / 5443 kg @ 1 14 bar Pressure Range .......... ...

  • Stanley Black & Decker CT06 - page 17

    CT06 User Manual ◄ 17 CT06 P ARTS ILL USTRA TION ...

  • Stanley Black & Decker CT06 - page 18

    18 ► CT06 User Manual CT06 P ARTS LIST ITEM NO. P ART NO. QTY DESCRIPTION 1 001 14 1 ROLL PIN 2 001 18 1 RET AINING RING 3 00144 12 HSHCS 4 07626 2 O-RING ■ 5 09330 1 O-RING ■ 6 00294 1 O-RING ■ 7 00360 1 O-RING ■ 8 00769 2 HSHCS 9 00936 2 ADAPTER 10 01259 1 O-RING ■ 11 01534 1 ROLL PIN 12 01608 4 STEEL BALL 13 01809 1 V AL VE SPOOL 14 ...

  • Stanley Black & Decker CT06 - page 19

    ...

  • Stanley Black & Decker CT06 - page 20

    Stanley Hydraulic T ools 3810 SE Naef Road Milwaukie, Oregon 503-659-5660 / Fax 503-652-1780 www .stanleyhydraulic.com IMPORT ANT T o ll out a Product Warranty Recording form, and for information on your warranty , visit Stanleyhydraulic.com and select the W arranty tab. ( NOTE: T he warranty recording form must be submitted to validate the warr ...

Produzent Stanley Black & Decker Kategorie Automobile Parts

Dokumente, die wir vom Produzenten des Geräts Stanley Black & Decker CT06 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Stanley Black & Decker
- Bedienungsanleitungen CT06
- Produktkarten Stanley Black & Decker
- Informationsbroschüren
- oder Energieetiketten Stanley Black & Decker CT06
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Stanley Black & Decker CT06.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Stanley Black & Decker CT06, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Stanley Black & Decker CT06. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Stanley Black & Decker CT06 ansehen.

Die komplette Bedienungsanleitung des Geräts Stanley Black & Decker CT06, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Stanley Black & Decker CT06 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Stanley Black & Decker CT06 verständlich ist.

Eine gänzliche Bedienungsanleitung von Stanley Black & Decker sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Stanley Black & Decker CT06 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Stanley Black & Decker CT06 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Stanley Black & Decker CT06, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Stanley Black & Decker CT06 - die uns die ersten Schritte während der Nutzung von Stanley Black & Decker CT06 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Stanley Black & Decker CT06 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Stanley Black & Decker CT06 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Stanley Black & Decker CT06?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Stanley Black & Decker CT06 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Stanley Black & Decker CT06 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)