Deutsch dropdown-ico

Bedienungsanleitung Philips Video Camera

34 Seiten 2.55 mb
Download

Zur Seite of 34

Summary
  • Philips Video Camera - page 1

    1 Installation and Operating Manual Fastrax Dome Video Camera for Ceiling and W all Mounting EDC-141E, EDC-142E, EDC-143E, EDC-142E1, EDC-144E, EDC-142E2 ...

  • Philips Video Camera - page 2

    2 3 Contents 1. Introduction .............................................................................................................................................................................................................. 3 1.1 Features ................................................................................................... ...

  • Philips Video Camera - page 3

    2 3 Safety Instructions • Read these safety instructions and the operation manual rst before you install and commission the camera. • Keep the manual in a safe place for later reference. • Protect your camera from contamination with water and humidity to prevent it from permanent damage. Never switch the camera on when it gets wet. Have it ...

  • Philips Video Camera - page 4

    4 5 Figure 1 - T ypical System Conguration Figure 2 - Assemble bubble ring ass’y Note: It is recommended to remove camera window for improving picture quality when you assemble bubble ring ass’y . up to 255 multiplexer Alarm Input (up to 8) <Sensor> <Siren> <Flashing light> Alarm Output (up to 4) J-box Master keyboard up to ...

  • Philips Video Camera - page 5

    4 5 2. Installation and Conguration 2.1 Package Contents The package contains the following: 1x Fastrax II E (Dome Camera) 1x Bubble Ring 1x Instruction Manual (This Document) 3x Assembly Screws for Attaching Fastrax II E 3x Plastic Anchor 1x 10Pin Connector 2x 12Pin Connector CAUTION: Be sure to have caution labels (E version only) on both body ...

  • Philips Video Camera - page 6

    6 7 2.2 Basic Conguration of Fastrax II Dome Camera System Figure 4- Basic installation diagram The dome camera must be installed by qualied service personnel in accordance with all local and federal electrical and building codes. The system should be installed according to Figures 4 through 9. Power 24V AC STP AWG #24 Sensor Alarm input up t ...

  • Philips Video Camera - page 7

    6 7 2.2.1 Single Multiplexer Figure 5 - Single Multiplexer Rear Keyboard controller Power 24V AC BNC Main Monitor BNC BNC RS-485 (–) Pin No. 4 RS-485 (+) Pin No. 6 J-Box (Back) J-Box (Front) AWG #24 Power 24V AC Power 24V AC Spot Monitor Multiplexer ...

  • Philips Video Camera - page 8

    8 9 2.2.2 Single User with T wo Multiplexer Figure 6 - T wo Multiplexer Rear Keyboard controller Power 24V AC BNC 1st Main Monitor BNC BNC RS-485 (–) Pin No. 4 RS-485 (+) Pin No. 6 J-Box (Back) J-Box (Front) AWG #24 Power 24V AC Power 24V AC Spot Monitor 1st Multiplexer BNC 2nd Multiplexer 2nd Main Monitor Spot output of the rst multiplexer to ...

  • Philips Video Camera - page 9

    8 9 2.2.3 T wo Multiplexer with Slave Keyboard Controller Figure 7 - T wo Multiplexer with Slave Keyboard Controller Rear Keyboard controller Master Power 24V AC BNC 1st Main Monitor BNC BNC RS-485 (–) Pin No. 4 RS-485 (+) Pin No. 6 J-Box (Back) J-Box (Front) AWG #24 Power 24V AC Power 24V AC Spot Monitor for Master K/B 1st Multiplexer BNC 2nd Mu ...

  • Philips Video Camera - page 10

    10 11 2.2.4 T wo Multiplexer with Slave Keyboard Controller (method 2) Figure 8 - T wo Multiplexer with Slave Keyboard Controller (method 2) Spot output 1 of the rst multiplexer to be connected to 16 th input of the second multiplexer . n: User , Spot out of n th to be connected to (17-n) th camera input of the 2 nd multiplexer . n th spot out o ...

  • Philips Video Camera - page 11

    10 11 Figure 9 - Layout of Switches 2.3 Setting Unit for T ermination The device which is connected at end of line, whether it is a dome camera or keyboard controller , must ha ve the cable for communication terminated by setting the appropriate DIP switch. Without proper termination, there is potential for control signal errors. T otal length of t ...

  • Philips Video Camera - page 12

    12 13 2.4 Setting Address (ID) of Dome Camera T o prevent dama ge, each dome camera must have a unique address (ID). When installing multiple dome cameras using a multiplexer , it is suggested that the dome camera address matches the multiplexer port number . If you wan to set the address more than 999, you should connect the ser vice provider . Ex ...

  • Philips Video Camera - page 13

    12 13 2.5 Setting Protocol of Dome Camera If a dome camera is to be installed with a Fastrax keyboard controller , select F2 protocol. Consult service personnel if a dome camera is installed with device other than a keyboard controller . Unless Baud rate match, universal protocol will not work. Figure 13 – Protocol Selection Switches D11 D12 Came ...

  • Philips Video Camera - page 14

    14 15 2.6 Connection • Connecting to the RS-485/-422 NO TE: Should you experience any control problems when using the Pelco-protocol, connect the ground plate (GND) to the control component. The dome camera can be controlled remotely by an external device or control system, such as a control keyboard, using RS-485 half-duplex, RS-422 duplex or si ...

  • Philips Video Camera - page 15

    14 15 DOME MENU AUTO SCAN PRESET TOUR P ATTERN ALARM AREA TITLE PRIV ACY ZONE CAMERA DOME SETUP EXIT(ESC TO EXIT) 3. Program and Operation 3.1 Selecting Dome Camera Before you program or operate a dome camera, you must select the dome camera by pressing the dome camera No. + CAM successively . Example: Pressing 1 , 0 and CAM key sequentially will s ...

  • Philips Video Camera - page 16

    16 17 AUTO SCAN SETUP SCAN 01 : AUTOSCAN01 SPEED(MODE) : F AST VECTOR ST ART ANGLE : 127.1, 027.7 X7 END ANGLE : 157.7, 080.7 X13 SCAN DIR. : CCW SWAP : OFF SAVE AND EXIT (ESC TO CANCEL) HOLD DOWN CTRL KEY WHILE SELECT POSITION. 3.4 Auto Scan (First Item of the Main menu / Shortcut: Scan ) The Auto scan supports up to 8 programmed angles a t user - ...

  • Philips Video Camera - page 17

    16 17 3.5 Preset (Second Item of the Main menu / Shortcut: Prst ) If you need to view specic locations routinely , you should program presets. A preset is a programmed video scene with automatic pan, tilt, zoom, focus and iris settings. Once programmed, entering the number and pressing a Preset button on your controller automatically calls up th ...

  • Philips Video Camera - page 18

    18 19 3.6 Shortcut of Preset Program Select a view to be stored (direction of the camera, zoom and focus), then press No. ( 1 to 240 ), and then press Pgm , Prst subsequently . The current view will be stored to the selected preset number if position is empty . If selected preset number is not empty , „PRESET EXISTING” message will be displayed ...

  • Philips Video Camera - page 19

    18 19 4. T o add a stored preset as a T our , twist the Zoom handle or press Zoom Key (Programmed preset will scroll). T o remove a stored preset from the T our , press the Home key , blank position mark (===) will be displayed. Y ou can overwrite the programmed position. 5. T o place functions other than preset, press T our , Ptrn, or Scan for T o ...

  • Philips Video Camera - page 20

    20 21 3.9 Alarm (This menu shows on only specic model, F ifth Item of Main menu) ALARM SETUP NO PRI PRS IN OUT HLD LA TCH 01 1 001 OFF OFF 03 OFF 02 8 001 OFF OUT1 03 OFF 03 1 240 NO OUT1 03 OFF 04 2 001 NC OUT4 03 OFF 05 1 001 OFF OFF 03 OFF 06 8 001 OFF OUT1 03 OFF 07 1 240 NO OUT1 03 OFF 08 2 001 NC OUT4 03 OFF SAVE AND EXIT (ESC TO CANCEL) N ...

  • Philips Video Camera - page 21

    20 21 Pages can be scrolled through by pushing the Joystick to the left or right on the rst or last column of the menu. Pushing the Joystick to left on the „NO” column (01 ~ 08) of the menu to scroll to the previous page. Push the Joystick to right on the „END” column to go to the next page. 1. Press Menu to display the main menu on the ...

  • Philips Video Camera - page 22

    22 23 CAMERA SETUP FOCUS CONTROL WB CONTROL AE CONTROL LINE LOCK CONTROL SHARPNESS : 9 BACK LIGHT : OFF DIGIT AL ZOOM : OFF (2x/4x/ MAX) NIGHT SHOT CONTROL (optional) SAVE AND EXIT (ESC TO CANCEL) 3.12 Camera (Eighth Item of Main menu) NOTE: The menu features will v ar y depending on the camera module installed in your dome camera. SHARPNESS The hi ...

  • Philips Video Camera - page 23

    22 23 • WB (white balance) CONTROL MODE : MANUAL / AUTO / INDOOR / OUTDOOR / ONE PUSH / A TW RGAIN : 0 ~ 255 BGAIN : 0 ~ 255 Use the ATW mode for normal use. RGAIN / BGAIN modes are controllable only in MANUAL Mode. Push the Joystick to the right or left to change. NOTE : „ONE PUSH” means that when rotating the Joystick handle for a moment th ...

  • Philips Video Camera - page 24

    24 25 • AE CONTROL AE SETUP MODE : FULL AUTO SLOW SHUTTER : MANUAL IRIS : F2.4 GAIN : 0 DB BRIGHT : 14 SHUTTER : 1/60 EXIT (ESC TO EXIT) EDC-141E EDC-142E EDC-144E MODE FULL AUTO / MANUAL / IRIS PRIO / SHUTTER PRIO / BRIGHT SLOW SHUTTER AUTO / MANUAL – AUTO effects only FULL AUTO mode IRIS : CLOSE / F22 / F19 / F16 / F14 / F11 / F9.6 / F8.0 / F ...

  • Philips Video Camera - page 25

    24 25 MODE : INTERNAL / EXTERNAL. Adjusts phase of picture with other cameras in EXTERNAL mode. PHASE : 0~255 EXIT (ESC TO EXIT) • NIGHT SHOT MENU (not at EDC-142E1 and EDC-142E) The NIGHT SHOT option removes the IR cutoff lter of the camera and makes the camera sensitive to near infrared. This will set the BLACK & WHITE option to ON autom ...

  • Philips Video Camera - page 26

    26 27 CONFIGURA TION MENU LANGUAGE SETUP HOME FUNCTION SETUP OSD DISPLA Y VIEW ANGLE SETUP INITIALIZE DA T A ORIGIN OFFSET DOME RESET SYSTEM INFORMA TION EXIT (ESC TO EXIT) 3.13 Dome Setup (Ninth Item of Main menu) LANGUAGE SETUP LANGUAGE : ENGLISH SAVE AND EXIT (ESC TO EXIT) • LANGUAGE SETUP LANGUAGE : Select the language you want. * This setup ...

  • Philips Video Camera - page 27

    26 27 • OSD DISPLA Y OSD DISPLA Y SETUP CAMERA TITLE : DOMEID VIEW DIRECTION : OFF DOME OSD DISPLA Y : ON AREA DISPLA Y : OFF SAVE AND EXIT (ESC TO CANCEL) CAMERA TITLE : 8 CHARACTER CAN BE SET VIEW DIRECTION : ON / OFF DOME OSD DISPLA Y : ON / OFF AREA DISPLA Y : ON / OFF • VIEW DIRECTION „ON” sets current direction as N(North) and the coo ...

  • Philips Video Camera - page 28

    28 29 • FLIP Allows the dome camera to automatically turn 180 degrees when the camera tilts to its lower position. When camera reaches oor alone moving object, it will stop. Release the Joystick handle instantly and then pull down to run ip fucntion. The speed of following object will be same speed as previous. • TIL T Over Angle Thi s op ...

  • Philips Video Camera - page 29

    28 29 SYSTEM INFORMA TION CAMERA TYPE : XXXXXXX H/W VERSION : V2.1 ROM VERSION : V2.11 PROTOCOL : F2E BAUDRA TE : 9600BPS EXIT (ESC TO EXIT) A Dome camera’ s Setup menu provides essential information about the dome camera when ser vice is required. When you view this screen, you can determine the camera type, ROM version. The information on this ...

  • Philips Video Camera - page 30

    30 31 5. Glossar y Alarm Actions The assigned responses for the dome camera when inputs change from normal to abnormal states. The dome may run a Preset, Pattern, or have no assigned action for each of the four dome inputs. The dome may also send alarm states to the host controller for processing. See also Input and Normal Input State. Areas Progra ...

  • Philips Video Camera - page 31

    30 31 6. Short Cut Key Short Cut Key Function PRST Pop up preset setup menu TOUR Pop up guard T our setup menu PTRN Pop up P a ttern setup menu SCAN P op up Auto Scan setup menu NO. + PGM + PRST Store the current view at the selected number NO. + PGM + TOUR Pop up tour setup menu at the selected number NO. + PGM + SCAN Pop up auto scan setup menu a ...

  • Philips Video Camera - page 32

    32 33 7. Specications Model EDC-142E EDC-141E EDC-143E EDC-142E1 EDC-144E EDC-142E2 EDP 74081 74086 74091 74093 74100 74117 Imager 1/4” 752 (H) x 582 (V) pixels (Son y ExView Interline T ransfer CCD) Sensitivity 1.0Lux at F1.4 (0.75Lux at F1.2) 0.7Lux at F1.4 (0.5Lux at F1.2); 0.05Lux at 1/3sec. shutter speed; 0.01Lux at 1/3sec. shutter speed ...

  • Philips Video Camera - page 33

    32 33 Model EDC-142E EDC-141E EDC-143E EDC-142E1 EDC-144E EDC-142E2 EDP 74081 74086 74091 74093 74100 74117 Shutter modes – High and Low Speed shutter – High and Low Speed shutter – Synchronization Internal/AC line lock, phase adjustment via remote control White balance Modes: Manual, Automatic, Indoor , Outdoor , A TW Video output 1Vp-p, CVB ...

  • Philips Video Camera - page 34

    34 Accessories EDP No. Description 74088 System Keyboard with 3-axis Joystick, 12VDC/230V AC 74092 System Keyboard with Joystick, 5” Monitor , 12VDC/230V AC 75201 Matrix, Multiplexer and T elemetr y Keyboard with Joystick, RS-485 Control 74057 Flush Mount Dome Housing, Smoked Bubble, 4.9” 74078 Pendant Mount Outdoor Dome Housing, T inted Bubble ...

Produzent Philips Kategorie Digital Camera

Dokumente, die wir vom Produzenten des Geräts Philips Video Camera erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Philips
- Bedienungsanleitungen Video Camera
- Produktkarten Philips
- Informationsbroschüren
- oder Energieetiketten Philips Video Camera
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Philips Video Camera.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Philips Video Camera, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Philips Video Camera. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Philips Video Camera ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Philips Video Camera, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Philips Video Camera hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Philips Video Camera verständlich ist.

Eine gänzliche Bedienungsanleitung von Philips sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Philips Video Camera bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Philips Video Camera befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Philips Video Camera, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Philips Video Camera - die uns die ersten Schritte während der Nutzung von Philips Video Camera erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Philips Video Camera hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Philips Video Camera im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Philips Video Camera?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Philips Video Camera nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Philips Video Camera hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)