Español dropdown-ico

Manual de instrucciones JAI CV-A1

24 de páginas 1.22 mb
Descargar

Pasar a la página of 24

Summary
  • JAI CV-A1 - page 1

    Compact Monochrome Megapixel Progressive Scan Camera CV -A1 Operation Manual Camera: Revision B Manual: V ersion 1.2 A1manB12oct08.doc JPT 08 -10-03 ...

  • JAI CV-A1 - page 2

    CV-A1 Table of Contents 1. General......................................................................................................... 2 2. Standard Compositi on ....................................................................................... 2 3. Main Features ............................................................................ ...

  • JAI CV-A1 - page 3

    CV-A1 1. Gener al The CV-A1 is a monochrome progressive scan 1/ 2” CCD c amera with 1.4 Megapixel resolution . It is designed for automated inspection, featuring a small hou sing and a wide range of unique functions. The asynchronous trigger can be set to work in several mode s, to allow such functions as pulse width controlled shutter, p rogramm ...

  • JAI CV-A1 - page 4

    CV-A1 4. Locations and F unctions Fig. 1. Locations. 1. 12 pin Hirose connector for frame grabber interfacing and power (12V DC). 2. BNC connector for video output. VS 1.0 Vpp 75 Ohm. 3. 6 pin Hirose connector for trigger input and RS-232C control interface. 4. Gain potentiometer for manual gain setting. 5. Mounting holes, 8 x M3. For prec ision mo ...

  • JAI CV-A1 - page 5

    CV-A1 5. Pin Assignment 5.1. 12-pin Multi-connector (DC- IN/VIDEO OUT, EXT.HD/VD IN) Type: HR10A-10R-12PB-01 (Hirose) male Seen from re ar P in configuration is compat ible with EIAJ standard Fig. 2. 12-pin connector. Plugs for cable: HR10A-10P-12S 5.2. 6-pin Multi-connector (TRIGGER) Type: HR10A-7R-6PB (Hirose) male Pin no. Signal Remarks 1 GND 2 ...

  • JAI CV-A1 - page 6

    CV-A1 5.3. Input and Output Circuits In the following schematic diagrams the input and outpu t circuits for video and timing sig nals are shown. For alternat ive connections refer to “7.4. Intern al Switch and Jumper Se ttings.” Jumper settings are shown as for factory defaul t. 5.3.1. Video output 300 mV 500 mV GND #4/1 2 75 Video Out pu t NC ...

  • JAI CV-A1 - page 7

    CV-A1 5.4. CV-A1 Block Diagram Fig. 8. Block diagram. 6. F unctions and Oper ations 6.1. Basic functions Some of the primary camera functions need a general introduction before the ope ration modes are described. The list below sh ows the primary functions fr om the command list. SM Shutter Mode Normal shutter, Progra mmable Exposure SH Shutter Spe ...

  • JAI CV-A1 - page 8

    CV-A1 Binning mode BI is a fun ction where the signal charge from 2 or m ore adjacent pixels are adde d together and read out as one pixel. A resulting full frame with lower resolution can be read out with a higher rate. By adding 2 pixels together, the sensitivity is doubled. The CV-A 1 has both vertical and horizontal binning. Wit h V binning the ...

  • JAI CV-A1 - page 9

    CV-A1 6.2. Input-output of HD/VD Signals In the default setting the camera will accept external HD/VD signals on pin 6 and 7 of the 12 pin Hirose connector. If external HD/VD is applied, th e camera will synchronize to it. If no external sync signals are applied, the camera will oper ate with its in ternal x-tal controlled sync. The camera scanning ...

  • JAI CV-A1 - page 10

    CV-A1 6.3. Continuous Operation (Non triggered) Trigger Mode Normal. TR=0. It is for applications where the camera is continuous ru nning without external trigger. In norm al mode the shutter mode can be n ormal or programmable exposure. (SM=0 SM=1). The shutter will work in all 16 steps up to 1/200,000 second or with the programmable exposure in 1 ...

  • JAI CV-A1 - page 11

    CV-A1 6.4. External Trigger Modes This camera has 6 external asynchr onous trigger modes, wh ich can be set by RS-232C comman ds. 1. Edge Pre-select Mode.TR=1 Pre-selected exposure. (SM=0, SM=1) 2. Pulse Width Control Mode. TR=2 Pulse width controlled exposure. (HC=0, H C=1) 3. Frame Delay read out mode. TR=3 PWC exp osure read out by ext. VD. (HC= ...

  • JAI CV-A1 - page 12

    CV-A1 6.5. Edge Pre-select Mode The exposure starts at the first HD pulse after t he trigger leading edge. It stops and is read out after the duration of the shutter time selected. It can be t he first 9 step in normal or 10 23 steps in programmable shutter. SM=0 or SM=1. Shutter selections SH ≥ 10 will result in 1 /12,000 sec. This mode will ope ...

  • JAI CV-A1 - page 13

    CV-A1 6.6. Pulse Width Control Mode In this mode the exposure starts from the leading edge of the trigger pulse. It stops at the trailing edge of the trigger pulse, and the resul ting video is read out. The accumul ation can be either H synchronous or H asynchronous. HC=0 o r HC=1. In H synchronou s mode the accumulation starts at the first HD puls ...

  • JAI CV-A1 - page 14

    CV-A1 6.7. Frame-delay read out Mode In this mode the exposure starts from the leading edge of the trigger pulse. It stops at the trailing edge of the trigger pulse. The accu mulation can be either H sy nchronous or H asynchronous. HC=0 or H C=1. In H synchronous mode the accumulation starts at the first HD pulse after the leading edge of the t rig ...

  • JAI CV-A1 - page 15

    CV-A1 6.8. Long Time Exposure Mode The exposure time is the interval between 2 ex ternal VD pulses sent to the VD inp ut. The exposure starts after the input of a VD, and it ends after the next VD input, which again starts a new exposure. The interval between the external VD pulses (exposure time) can be from V to ∞ . Thermal and dark current noi ...

  • JAI CV-A1 - page 16

    CV-A1 6.9. Start/Stop Mode The exposure is controlled by the interval between the external trigge r pulse and an external VD pulse. The exposure start at the first HD pulse af ter the trigger leading edge, and it stops after the rising edge of the VD. An EEN pulse will in dicate the active accumu lation time, and a WEN pulse indicates that the resu ...

  • JAI CV-A1 - page 17

    CV-A1 6.10. Smearless Mode This mode will reduce the unwant ed smear signal from a highlighted scene when a short exposure time is used. The trigger mode is like edge pre-se lect, but a dummy readout is performed before the active accumulation is started. It will remove the smear abov e the highlighted parts in the image, but there is still smear l ...

  • JAI CV-A1 - page 18

    CV-A1 6.11. Other Functions. Gain and analogue settings. !! Do not adjust these s ettings unless you have knowl edge to video adju stments !! The video gain can be set to AGC or manual . In AGC mode the video level is kept constant by the automatic gain control circuit within a 1 2 dB range. Normal 700 mVpp ± 30 mV. The level can be adjusted with ...

  • JAI CV-A1 - page 19

    CV-A1 7.2. CV-A1 RS-232C command list. Command Name Format Parameter Remarks A – General settings and useful co mmands EB Echo Back EB= [ Param. ] <CR><LF> 0=Echo off 1=Echo on Off at po wer up ST Camera Status request ST?<CR><LF> Actual setting HP Online Help reques t HP?<CR><LF> Command li st VN Firm ware ver ...

  • JAI CV-A1 - page 20

    CV-A1 7.3. Camera Control Tool for CV-A1 From www.jai.com CV-A1 Camera Control Tool for Windows 98/NT/200 0 can be downloaded. The control tool contents a camera control program and too ls for making your own program. Below the different windows are sh own. Control Bar Windows for all functions Fig. 26. Windows from Camera Tools. For the integrator ...

  • JAI CV-A1 - page 21

    CV-A1 7.4. Internal Switch and Jumper Settings For VD and HD input/ou tput and termination refer to “6.2. I nput-output of HD/VD Signals.” For alternative connections of pin #10 and #11 on 12-pin connector, ju mper JP1, JP2, JP3, JP4 and JP5 can be used. Refer “5.3. Input and Output Circuits.” Jumper setting for alternative pin c onfigurati ...

  • JAI CV-A1 - page 22

    CV-A1 9. Specifications Specifications CV-A1 Scanning system Progressive 1068 lines 16.037 frames/sec. Pixel clock 28.63636 MHz Line frequency 17.127 kHz (1672 pixel clock/line) Frame rate for full frame 16.037 frames/sec. (1068 lines/frame) CCD sensor 1/2” progressive monochrome IT CCD. Sony ICX205AL-6 Sensing area for video out 6.42 (h) x 4.81 ...

  • JAI CV-A1 - page 23

    CV-A1 10. Appendix 10.1. Precautions Personnel not trained in dealing with similar elec tronic devices should not service this camera. The camera contains components sensitive to el ectrostatic discharge. The handling of these devices should follow the requirements of electrostatic se nsitive components. Do not attempt to disassemble this camera. D ...

  • JAI CV-A1 - page 24

    CV-A1 11. Users Record Camera type: CV-A1 Revision: (Revision B) Serial No. …………….. Users Mode Settings Users Modifications DECLARA TION OF CONFORMITY AS DEFINED BY THE COUNCIL DIRECTIVE 89/336/EE C EMC (ELECTROMAGNETIC COMPAB ILITY) WE HEREWITH DECLARE THAT THIS PRODUCT COMPLIES WITH THE FOLOWING PROV ISIONS APPLYING TO IT. EN-50081-1 EN ...

Fabricante JAI Categoría Security Camera

Los documentos del dispositivo JAI CV-A1 que obtenemos del fabricante se pueden dividir en varios grupos. Entre ellos están::
- dibujos técnicos JAI
- manuales de instrucciones CV-A1
- hojas de producto JAI
- folletos informativos
- o etiquetas energéticas JAI CV-A1
Todos son importantes, pero lo más importante desde el punto de vista del usuario de un dispositivo lo encontraremos en el manual de instrucciones JAI CV-A1.

Un conjunto de documentos determinado como manual de instrucciones se divide también en tipos más detallados, tales como: instrucciones de montaje JAI CV-A1, instrucciones de servicio, instrucciones cortas o instrucciones de usuario JAI CV-A1. Dependiendo de la situación debes buscar el documento que necesitas. En nuestra página puedes consultar el manual de instrucciones más popular del producto JAI CV-A1.

Manuales de instrucciones parecidos

El manual de instrucciones del dispositivo JAI CV-A1, ¿cómo debería ser?
El manual de instrucciones, también determinado como el manual de usuario o simplemente instrucciones, es un documento técnico que tiene como objetivo ayudar a los usuarios a utilizar JAI CV-A1. Las instrucciones normalmente las realiza un escritor técnico pero en un lenguaje comprensible para todos los usuarios de JAI CV-A1.

El manual de instrucciones completo de JAI debe contener unos elementos básicos. Una parte de ellos es menos importante, como por ejemplo: la portada / la página principal o las páginas de autor. Sin embargo, lo demás debe facilitarnos la información más importante desde el punto de vista del usuario.

1. Introducción y pistas sobre cómo orientarse con el manual JAI CV-A1 - Al principio de cada manual se deben encontrar las indicaciones acerca de la manera de usar un manual de instrucciones. Debe contener información sobre dónde encontrar el índice JAI CV-A1, preguntas frecuentes o problemas más comunes – son los apartados más buscados por los usuarios de cada manual de instrucciones.
2. Índice - listados de todos los consejos acerca de JAI CV-A1 que encontraremos en el documento
3. Consejos de uso de las funciones básicas del dispositivo JAI CV-A1 - que deben facilitarnos los primeros pasos durante el uso de JAI CV-A1
4. Troubleshooting - una secuencia sistematizada de acciones que nos ayudará a diagnosticar los problemas más importantes con JAI CV-A1
5. FAQ - las preguntas frecuentes
6. Datos de contacto Información acerca de cómo encontrar los datos de contacto del fabricante / servicio de JAI CV-A1 en cada país si no somos capaces de solucionar el problema por nuestra cuenta.

¿Tienes una pregunta acerca de JAI CV-A1?

Utiliza el formulario que se encuentra abajo

Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con JAI CV-A1, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con JAI CV-A1 probablemente compartirá una forma de solucionarlo.

Copia el texto de la imagen

Captcha
Nueva imagen

Comentarios (0)