-
Haier HWM8000 - page 1
HWM8000 Fuzzy Computerized Automatic Washing Machine User's manual This manual is for Please read this manual carefully before using. Retain it for future reference. 0030805704B ...
-
Haier HWM8000 - page 2
Contents Names of the parts Safety precautions Trouble shooting * Answer to question Packing list Specification Installation and adjustment Usage of the drain hose Preparation before washing Put in the laundries Add the detergent and softener Use the operation knobs and buttons Installation the water inlet hose Disposal after washing * Finish washi ...
-
Haier HWM8000 - page 3
Adjustable foot Front control board Front fixed foot Rear fixed foot back cover Cabinet Drain hose Back faceplate Control panel film Control panel Lint filter(Installed by user) Filter cover Level meter Power line Pulsator Inner tub Detergent box Drier outlet cover T op lid B Cabinet handle Wa rm water valve Cool water valve T op lid A Adjustable f ...
-
Haier HWM8000 - page 4
Safety precautions In normal usage of the washing machine, the power plug shall be ready to be pulled or plugged with hand. Be sure to pull the plug off and close the water faucet in following cases: power failure, delivering the machine, setting the machine idle or cleaning the machine. Do not plug or pull the power plug with wet hand. In case the ...
-
Haier HWM8000 - page 5
Do not put hand into the rotating tub. It is dangerous even if the rotation speed is slow. Take special care of the children. Keep children away from the washing machine to avoid them climbing on it. Do not decompose, repair or alter the machine by yourself. Do not put any hot or heavy items (such as the kettle with hot water) on the washing machin ...
-
Haier HWM8000 - page 6
Install the bottom plate Adjust the installation position Please install and adjust the machine according to the requirement of the manual, which is very important for you to operate the machine safely and properly. After opening the package, please lean the washing machine gently down on soft items (like towel cloth, blanket, etc.). Install the bo ...
-
Haier HWM8000 - page 7
Inner tub Lint filter After opening the package, please take out the lint filter from the document bag, install it to the filter cover of inner tub. See to the figure. Install the lint filter How to change the direction of the drain hose 1. The height of the drain hose shall be less than 10cm, or the drainage will not be smooth, and cost such long ...
-
Haier HWM8000 - page 8
Install the water inlet pipe Connection between the water inlet hose jointer and the water faucet Water faucet, suitable water fauce t, not suitable It is required that the front end shall be longer than 10mm. The outlet end surface of the faucet shall be flat and smooth. If not, please file it smooth to avoid leakage. 2 Loosen the four screws of t ...
-
Haier HWM8000 - page 9
Dismount the water inlet hose Connection between the water inlet hose jointer and the water inlet hose Check the connection between the water inlet hose jointer and the water faucet 1.Swing the hose gently to check if it is fastened stably. 2.After installation, open the faucet to check if it leaks water. 3.Do not bend the hose by force. 4.Each tim ...
-
Haier HWM8000 - page 10
1 Pr eparation bef or e washing Pay attention to the followings before washing Preparation before washing 1 Connect the water inlet hose. Open the water faucet. 2 Confirm that the washing machine is earthed reliably . Then plug the power plug into the receptacle. The earthing terminal shall not link to gas pipeline and faucet water pipeline. 3 Put ...
-
Haier HWM8000 - page 11
The capacity of washing and spinning refer to the largest weight of the standard laundries under dry condition that can be washed or spinned in one cycle. Washing quantity for one cycle shall be less than the rated capacity. The thickness, size and type of the cloth will influence the actual washing capacity. It is feasible to put in suitable amoun ...
-
Haier HWM8000 - page 12
a Description of the function of the operation buttons BALANCE DISPLA Y If the bulb of the level meter is insid e the standar d circle, it indicates that the mach ine is horizon tal. CURRENT button When the washing ma chine starts running, i t will set the current automatically. You can select current by self according to the actual requirement. Pl ...
-
Haier HWM8000 - page 13
Standard Common washing Night Low noise washing during night Gentle Washing the woolen textiles or underwear FA ST 10-minute quick washing of laundries with light soil PROGRAM button The following four programs are available for your option SURPLUS RESERVE HOURS LATER FAST GENTLE FUZZY STANDAR D NIGHT SOAK WAS H RINSE SPIN START PAUSE SELECT PROGRA ...
-
Haier HWM8000 - page 14
2 Push the program button to select suitable automatic program. 3 Push the select button to select suitable procedure. After switching on the power , the washing machine will set to WASH-SPIN procedure automatically. It is the common procedure. T o select other procedures, push the SELECT button to select one or more procedures from SOAK, WASH, RIN ...
-
Haier HWM8000 - page 15
Times of pushing the SELECT button Push the SELECT button for 6 times, and it will resume the initial mode. It will circulate in that sequence. The SOAK procedure can work in cooperation with automatic programs like standard and night. There is intermittent pulsator stirring during soak. Selected procedure Applicable circumstance Contents (the ligh ...
-
Haier HWM8000 - page 16
5 Close the top lid. 6 Finish washing. It beeps to indicate the finishing of washing The power w ill be switched off automatically after the finishing of the washing. If yo u op en the t op lid, t he machine w ill stop working before sp inning. 7 Disposal After W ashing If the cabinet is dirty, wipe it with wet soft cloth Do not wash with water dir ...
-
Haier HWM8000 - page 17
There may be some water flowing out of the drain hose in the first use of the machine. It is the water remained in the machine during the ex-factory performance inspection. Phenomenon Reason How to solve It rings after starting the Reserve function. The digitron displays E0. The water faucet leaks water There's abnormal sound inside the machin ...
-
Haier HWM8000 - page 18
Packing list User's manual One piece Fuzzy computerized automatic washing machine Lint filter Name One piece Eight pieces One piece One set T apping screws Quantity Bottom plate Two pieces W ater level/Water quantity (about) Injection pressure Specification 0.03MPa-0.78MPa The end connecting to the washing machine Jointer connecting the water ...
¿Tienes una pregunta acerca de Haier HWM8000?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Haier HWM8000, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Haier HWM8000 probablemente compartirá una forma de solucionarlo.