-
CDA FW852 - page 1
Customer Care Department • The Group Ltd. • Harby R oad • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : customer .care@cda.eu W : www .cda.eu www .cda.eu fw852 / fw872 Integrated Fridge Freezer Installation, Use and Maintenance ...
-
CDA FW852 - page 2
2 Important The manufacturer cannot be held responsible for injuries or losses caused by incorrect use or installation of this product. Please note that we reserve the right to invalidate the guarantee supplied with this product following incorrect installation or misuse of the appliance. This appliance is not designed to be used by people (includi ...
-
CDA FW852 - page 3
3 This appliance has been manufactured to the strictest standards and complies with all applicable legislation, including Electrical safety (L VD) and Electromagnetic interference compatibility (EMC). Parts intended to come into contact with food conform to EEC/89/109 .4 IMPORT ANT INFORMA TION FOR CORRECT DISPOSAL OF THE PRODUCT IN A CCORD ANCE WI ...
-
CDA FW852 - page 4
4 Important Never store inflammable or explosive items and strong corrosive acids or alkalis in the appliance. This is a household appliance, which is produced in accordance with the national standard. It is intended for food storage only , not for storage of blood, medicine and biological products. T o prevent risk of fire, keep the appliance aw ...
-
CDA FW852 - page 5
5 Before First Use Y ou must allow the fridge to settle for at least twenty four hours prior to switching the power on. It is recommended that you clean the interior of the appliance prior to first use, using a solution of bicarbonate of soda and warm water and then thoroughly drying the interior . The fridge may have an odour to it at first use. ...
-
CDA FW852 - page 6
6 Use Fridge • Never put liquids in the refrigerator uncovered. • Never put hot foods in the refrigerator . W arm food should be allowed to cool to room temperature before being put into the refrigerator . • Nothing should rest against the rear wall of the refrigerator , as this will cause frost and possible condensation problems which will b ...
-
CDA FW852 - page 7
7 Freezer • The freezer compartments are designed to store only frozen food. • Never put hot or warm foods in the freezer , allow them to cool fully before putting them into the freezer . • Follow the instructions on the food packaging for storage of frozen food. If no information is provided, foods should not be stored for more than three mo ...
-
CDA FW852 - page 8
8 S torage The fridge section is for short term food storage. Although the temperature can be maintained between 0-10˚C, extended periods of food storage is not recommended. As the cold air circulates within the fridge, the temperature can vary between the dierent sections. As such, foods should be stored in dierent sections according to typ ...
-
CDA FW852 - page 9
9 Control P anel A. R efrigerator Button This button is used to adjust the fridge temperature between 2°C and 10°C in 1°C increments. T o change the temperature setting, press this button once so the display shows the set temperature and flashes. While it is still flashing, press this button several times until the required temperature is show ...
-
CDA FW852 - page 10
10 C. Freezer T emperature Display In normal running this shows the actual temperature in the freezer compartment. If the temperature in the freezer is higher than 0°C this will flash, otherwise it will be static. See below for how this display is used in setting the freezer temperature. D . Super Freeze Display The super freeze function can be u ...
-
CDA FW852 - page 11
11 After changing the temperature setting, the time taken to achieve the new temperature will depend on how big the change is from the previous setting. Switching On and O When the fridge freezer is connected to a power supply it will automatically switch on. It may be switched o without disconnecting the power supply by pressing and holding ...
-
CDA FW852 - page 12
12 Care and Cleaning Always disconnect the appliance from the power supply before any cleaning or maintenance. The fridge and freezer sections should be cleaned using a solution of bicarbonate of soda and lukewarm water . Do not use abrasive products or detergents. After washing, rinse and dry thoroughly . Clean the shelves and balconies separately ...
-
CDA FW852 - page 13
13 Defrosting the Fridge The fridge is self-defrosting. Any water created will run out of the fridge through the channel at the back of the fridge. It is important to keep the channel clear at all times using the cleaning tool supplied. The defrosted water is collected in the evaporating tray at the back of the appliance and dissipated by evaporati ...
-
CDA FW852 - page 14
14 the freezer compartment. • The freezer should be cleaned using a solution of bicarbonate of soda and lukewarm water . Do not use abrasive products or detergents. After washing, rinse and dry thoroughly . • Clean the drawers separately by hand with a mild solution of washing up liquid and water . Do not put them in the dishwasher . • Once c ...
-
CDA FW852 - page 15
15 T roubleshooting If you have any problems with your appliance, you should check the troubleshooting prior to calling CD A Customer Care to prevent unnecessary service calls and potential cost. If the appliance is not working • Check there is power to the appliance. • The house fuses are intact and the fuse in the plug has not blown. • The ...
-
CDA FW852 - page 16
16 There is water in the lower part of the refrigerator compartment • The drain hole in the channel at the back of the compartment is clear . Ice has formed on the back wall of the fridge • It is normal for some ice droplets to form on the back wall of the fridge. This does not constitute a fault with the appliance. • Ensure that no items ins ...
-
CDA FW852 - page 17
17 Installation and V entilation This appliance must never be installed close to heat sources, e.g. heating elements, cookers or in damp places. • T o ensure the appliance is level, you should use the height adjustable feet at the front of the appliance. • The cooling system at the rear of the appliance must not touch the rear wall. • The app ...
-
CDA FW852 - page 18
18 V entilation The main consideration when installing any refrigeration unit into a fitted kitchen is ventilation. The heat removed from the cooling compartment needs to be dissipated into the atmosphere. Incorrect ventilation can lead to premature compressor failure, ex cessive power consumption and total system failure. For products intended to ...
-
CDA FW852 - page 19
19 The open channel at the rear is clearly shown. For the correct operation of the appliance it is important that the top of the housing unit is not blocked o . A channel depth of 40-50mm is normal with most units. A hole is shown in the base shelf of the unit; this allows air to be drawn over the compressor & heat ex change. Some installers ...
-
CDA FW852 - page 20
20 Mounting the Fascia Doors • Position the appliance within the unit. Ensure that there is a gap of 3 to 4mm between the non-hinged side and the cabinet wall. • L ocate the slider in the bracket and fix the slider to the fascia door 20 to 22mm from the edge of the fascia as shown in figure 8, ensuring that the slider is positioned centrally ...
-
CDA FW852 - page 21
21 R eversing the Doors W e recommend you seek the help of another individual to support the doors whilst performing this operation. 1. Carefully prise o the cover cap for the top hinge and unscrew the screws fixing the top hinge to the appliance, you should support the upper door whilst doing this. 2. Carefully remove the upper door and place ...
-
CDA FW852 - page 22
22 Ensuring the door seals correctly: It is normal for the seal to be compressed after the door has been reversed. With the door closed, use a hair dryer to expand the seal and fill the gap between the door and the body of the appliance. T ake care not to use the hair dryer too close to the appliance, which could damage the seal. A distance of app ...
-
CDA FW852 - page 23
23 3. R eplace fuse cover . Important: Do not use the appliance without the fuse cover in position. How to connect an alternative plug If the fitted plug is not suitable for your socket outlet, then it should be cut o and disposed of safely to avoid possible shock hazard. A suitable alternative plug of at least 13 Amp rating to BS 1363 should b ...
-
CDA FW852 - page 24
Customer Care Department • The Group Ltd. • Harby R oad • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : customer .care@cda.eu W : www. cda.eu www .cda.eu Please contact our Customer Care Department for Service on the details below Customer Care Department The Group L td. • Harby Road • Langar • Nottingh ...
¿Tienes una pregunta acerca de CDA FW852?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con CDA FW852, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con CDA FW852 probablemente compartirá una forma de solucionarlo.