-
Chicago Electric 97588 - page 1
MAGNESIUM HEA VY DUTY 7” ANGLE GRINDER 97588 SET UP AND OPERA TING INSTRUCTIONS Distributed exclusively by Harbor Freight T ools ® . 3491 Mission Oaks Blvd., Camarillo, CA 9301 1 Visit our website at: http://www .harborfreight.com Read this material before using this product. Failure to do so can result in serious injury . SA VE THIS MANUAL. Cop ...
-
Chicago Electric 97588 - page 2
SKU 97588 For technical questions, please call 1-800-444-3353. Page 2 SA VE THIS MANUAL Keep this manual for the safety warn- ings and precautions, assembly , operat- ing, inspection, maintenance and cleaning procedures. Write the product’ s serial number in the back of the manual near the assembly diagram (or month and year of purchase if produc ...
-
Chicago Electric 97588 - page 3
SKU 97588 For technical questions, please call 1-800-444-3353. Page 3 plugs with grounded power tools. Unmodied plugs and matching out - lets will reduce risk of electric shock. A void body contact with grounded b. surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is grounded. ...
-
Chicago Electric 97588 - page 4
SKU 97588 For technical questions, please call 1-800-444-3353. Page 4 proved for the specic hazards in the work area. Power tool use and care 4. Do not force the power tool. Use a. the correct power tool for your ap- plication. The correct power tool will do the job better and safer at the rate for which it was designed. Do not use the power too ...
-
Chicago Electric 97588 - page 5
SKU 97588 For technical questions, please call 1-800-444-3353. Page 5 mum speed marked on the power tool. Accessories running faster than their RA TED SPEED can break and The outside diameter and the 5. thickness of your accessory must be within the capacity rating of your power tool. Incorrectly sized accessories can ...
-
Chicago Electric 97588 - page 6
SKU 97588 For technical questions, please call 1-800-444-3353. Page 6 could snag your clothing, pulling the accessory into your body . Regularly clean the power tool’ s 14. air vents. The motor ’s fan will draw the dust inside the housing and ex - cessive accumulation of powdered metal may cause electrical hazards. Do not operate the power tool ...
-
Chicago Electric 97588 - page 7
SKU 97588 For technical questions, please call 1-800-444-3353. Page 7 manual cannot cover all possible con- ditions and situations that may occur . It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator . Kickback and Related W arnings Kickback is ...
-
Chicago Electric 97588 - page 8
SKU 97588 For technical questions, please call 1-800-444-3353. Page 8 side of cut-off wheel. Abrasive cut- off wheels are intended for peripheral grinding, side forces applied to these wheels may cause them to shatter . Always use undamaged wheel 4. anges that are of correct size and shape for your selected wheel. Proper wheel anges support t ...
-
Chicago Electric 97588 - page 9
SKU 97588 For technical questions, please call 1-800-444-3353. Page 9 Grip tool as lightly as possible (while 6. the tool do the work. T o reduce vibration, maintain the tool 7. as explained in this manual. If any abnormal vibrat ...
-
Chicago Electric 97588 - page 10
SKU 97588 For technical questions, please call 1-800-444-3353. Page 10 Double Insulated T ools: T ools with T wo Prong Plugs T ools marked “Double Insulated” do 1. not require grounding. They have a special double insulation system and complies ...
-
Chicago Electric 97588 - page 11
SKU 97588 For technical questions, please call 1-800-444-3353. Page 1 1 RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS* (120/240 VOL T) NAMEPLA TE AMPERES (at full load) EXTENSION CORD LENGTH 25’ 50’ 75’ 100’ 150’ 0 – 2.0 18 18 18 18 16 2.1 – 3.4 18 18 18 16 14 3.5 – 5.0 18 18 16 14 12 5.1 – 7.0 18 16 14 12 12 7.1 – 12.0 18 ...
-
Chicago Electric 97588 - page 12
SKU 97588 For technical questions, please call 1-800-444-3353. Page 12 SPECIFICA TIONS Electrical Requirements 8000 RPM Wheel Diameter 7 inches Arbor Diameter Spindle Thread ? ...
-
Chicago Electric 97588 - page 13
SKU 97588 For technical questions, please call 1-800-444-3353. Page 13 Installing the Auxiliary Handle TO PREVENT SERIOUS INJUR Y : Do not operate this tool with one hand only or without the Auxiliary Handle properly installed. The Auxiliary Handle may be installed 7. in one of three positions, on either side or on top of the Gear Housing (26). (Se ...
-
Chicago Electric 97588 - page 14
SKU 97588 For technical questions, please call 1-800-444-3353. Page 14 Closely inspect the Grinding Wheel 4. before mounting. Perform a ring-test on the wheel (unless wheel is smaller than 4” or is an unusual shape) as follows: a. through the ...
-
Chicago Electric 97588 - page 15
SKU 97588 For technical questions, please call 1-800-444-3353. Page 15 W ork Piece and W ork Area Set Up Designate a work area that is clean 1. and well-lit. The work area must not allow access by children or pets to prevent injury and distraction. Route the power cord along a safe 2. route to reach the work area without creating a tripping hazard ...
-
Chicago Electric 97588 - page 16
SKU 97588 For technical questions, please call 1-800-444-3353. Page 16 MAINTENANCE AND SER VICING Procedures not specically explained in this manual must be performed only by a qualied technician. TO PREVENT SERIOUS INJUR Y FROM ACCIDENT AL OPERA TION: T urn the Power Switch of the tool to its “OFF” position and unplug the tool from its e ...
-
Chicago Electric 97588 - page 17
SKU 97588 For technical questions, please call 1-800-444-3353. Page 17 b. as shown in the illustration above. c. Use a small prying tool (not includ- ed) to hold the Spring Clips to the side while you remove the carbon brushes. Keep track of which ...
-
Chicago Electric 97588 - page 18
SKU 97588 For technical questions, please call 1-800-444-3353. Page 18 T roubleshooting Problem Possible Causes Likely Solutions T ool will not start No power at outlet. 1. Cord not connected. 2. Carbon Brushes may be worn or 3. damaged. Check power at outlet. 1. Check that cord is plugged in. 2. Inspect Carbon Brushes and replace if 3. necessary . ...
-
Chicago Electric 97588 - page 19
SKU 97588 For technical questions, please call 1-800-444-3353. Page 19 P ARTS LIST Part Description Qty . 1 Outer Flange Arbor Nut 1 2 Grinding Wheel (not included) - 3 Inner Flange 1 4 Quick Release Adjusting Nut m8 1 5 W asher 1 6 Wheel Guard Quick Release 1 7 Wheel Guard 1 8 Spindle 1 9 Woodruf f Key 1 10 Phillips Pan Head Screw m5 x 16 4 11 Spr ...
-
Chicago Electric 97588 - page 20
SKU 97588 For technical questions, please call 1-800-444-3353. Page 20 ASSEMBL Y DIAGRAM Record Product’ s Serial Number Here: Note: If product has no serial number , record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only , and are not avail- able individually as replacement parts. ...
-
Chicago Electric 97588 - page 21
SKU 97588 For technical questions, please call 1-800-444-3353. Page 21 REV 1 1h 90 DA Y W ARRANTY Harbor Freight T ools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days fr ...
¿Tienes una pregunta acerca de Chicago Electric 97588?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Chicago Electric 97588, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Chicago Electric 97588 probablemente compartirá una forma de solucionarlo.