-
Hoover Canisfer Cleaner with Power Nozzle - page 1
Canisfer Cleaner with Power Nozzle by Hoover ...
-
Hoover Canisfer Cleaner with Power Nozzle - page 2
Fill in and retain The vacuum cleaner you have just purchased is a combination cleaner. It has a motorized nozzie for carpet and floor cleaning and tools for other tasks. The model and serial number are located on the bottom’of the cleaner. For your personal records, please enter the COMPLETE model and serial number in the spaces provided and ret ...
-
Hoover Canisfer Cleaner with Power Nozzle - page 3
When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE Warning. injury: n To reduce the risk of fire, electric shock, or . . . . . . . . . . . . . . . . . . . Donotuseoutdoors3onw&t&~rface~ Close supervision is necessary when any appliance i ...
-
Hoover Canisfer Cleaner with Power Nozzle - page 4
Unpacking Unpack cleaner from carton and identify the parts shown. Re- move and dispose of the car& board packing. A. Canister cleaner : B. Power nozzle / C. Paper bag / D. Extension wands and hose / j The cleaner assembled will iook like the drawing below. B l&l 0 ‘I A liiiil 0 C -17 -18 3 ...
-
Hoover Canisfer Cleaner with Power Nozzle - page 5
1. 2. 3. 4. 5. 6. 7. 8. 9. Cover: remove by lifting up top section of carrying handle and pulling forward. Carrying handle Check bag indicator: shows red when paper bag should be checked for fullness. Extension wands: use with power nozzle. If added length is desired when using cleaning tools, add one or both wands to hose. Spring latch: locks exte ...
-
Hoover Canisfer Cleaner with Power Nozzle - page 6
How to assemble 1. Connect hose Insert hose end with cord into opening of cleaner, lining up largest projection on hose with largest notch of opening. Turn hose to the right to tighten. When hose is attached properly, hose cord plug will reach to receptacle on cleaner. Insert plug as deeply into the receptacle as possible. To disconnect hose, first ...
-
Hoover Canisfer Cleaner with Power Nozzle - page 7
To attach hose to wands, rotate plastic latch ring on hand grip until slots in opening align. Push hand grip onto wand so that button projection fits into slot. Turn plastic latch ring to lock wand in place. Push plug on power nozzle cord completely into receptacle under- neath hand grip. Always disconnect cleaner from electrical outlet before atta ...
-
Hoover Canisfer Cleaner with Power Nozzle - page 8
How to use Power nozzle The power nozzle adjusts automatically for cleaning hard surface floors and various heights of carpet. It is not recommended for very irregular surfaces such as brick, slate, and certain parquet floors unless it is unplugged from the cleaner. This will stop the agitator from rotating. If desired, the Wall/ Floor Brush (shown ...
-
Hoover Canisfer Cleaner with Power Nozzle - page 9
Cleaning tools The cleaning tools have many uses. Select the tool best suited for the cleaning task from the descriptions below. Adjust the suction regulator to select the amount of suction appropriate for the cleaning task. 1. Crevice tool may be used for radiators, dresser drawers, spaces between kitchen equipment. 2. Furniture nozzle may be used ...
-
Hoover Canisfer Cleaner with Power Nozzle - page 10
To connect and remove tools To connect tools, insert end of tool into extension wand and snap into position. To disconnect, press down on the center of the spring latch and remove tool. Tools’attach to hand grip by rotating plastic ring until slots in the opening align. Insert tool and turn latch ring, as shown, to lock tool in place. To remove t ...
-
Hoover Canisfer Cleaner with Power Nozzle - page 11
How to store Your cleaner can be stored on end as shown in the illustration. Store power nozzle with handle in upright position. The hose and extension wands can be stored disassembled from the cleaner if desired. Maintenance The following sections are concerned with proper maintenance of the cleaner. Familiarize yourself with these home maintenanc ...
-
Hoover Canisfer Cleaner with Power Nozzle - page 12
How to replace Disconnect cleaner from electrical outlet. 1. Remove cover by lifting top section of carrying handle and pulling forward. 2. Depress latch and lift out used bag. 3. Place lower notched edge of new bag collar into grooves located inside front of cleaner. 4. Pull collar forward until latch snaps into collar. Open folds of bag. Push top ...
-
Hoover Canisfer Cleaner with Power Nozzle - page 13
Clearing obstructions Remove larger items from carpet and floor surfaces before vacuuming to help prevent obstructions in hose, wands or nozzle connector, and to maintain cleaning effectiveness of your cleaner. To check for obstructions, first turn cleaner off and disconnect from electrical outlet; then disconnect power nozzle plug and wands from h ...
-
Hoover Canisfer Cleaner with Power Nozzle - page 14
Secondary filter How to clean Disconnect cleaner from eiectri- cai outlet. The secondary filter is located inside the cleaner behind the paper bag. To remove filter, first remove cover of cleaner, then lift out filter. Clean filter by rinsing it in water. When dry, slide filter back into position. Do not operate cleaner without the secondary filter ...
-
Hoover Canisfer Cleaner with Power Nozzle - page 15
1 MOTOR PULLEY AGITATOR PU 2. Return nozzle to original position; and lift off nozzle cover. 3. If the belt is not broken, pull it off the motor pulley. 4. Lift up end of agitator. Remove old belt from agitator pulley and replace with new belt. 5. Stretch belt back and attach to motor pulley. Hold opposite end of agitator in place. Push belt end ...
-
Hoover Canisfer Cleaner with Power Nozzle - page 16
6. Position nozzle cover on front lip of nozzle base. Press cover into place. Turn nozzle over and replace screws. Agitator brush roll When to replace Disconnect cleaner from electri- cal outlet. When agitator brushes are worn, the brush roll should be replaced. To check condition of brushes, move the edge of a card across agitator opening while tu ...
-
Hoover Canisfer Cleaner with Power Nozzle - page 17
I I AGITATOR END 1 3. Pull out shaft part way, then reinsert shaft to push out opposite agitator end. 4. Remove shaft, being careful to leave washer on shaft 5. Insert into other end to push out second agitator end. 6. Discard old agitator brush roll. 7. Place agitator ends into new brush roll, matching projections in roll with openings in ends. Pu ...
-
Hoover Canisfer Cleaner with Power Nozzle - page 18
Lubrication The motor is equipped with bearings, which have been lubricated for the life of the motor. The addition of lubricant could cause damage. Therefore, do not add lubricant to either motor bearing. The agitator is equipped with two ball bearings that should be lubricated periodically by a Hoover Factory Service Center or an Authorized Warra ...
-
Hoover Canisfer Cleaner with Power Nozzle - page 19
---...L.I*-.i^eeI - .- Service If the problem persists, check the Yellow Pages of your telephone book under “Vacuum Cleaners-Household” for your nearest Hoover Factory Service Center or Authorized Warranty Service Dealer where approved HOOVER service and genuine HOOVER replacement parts may be obtained. Provided with this product is a listing o ...
-
Hoover Canisfer Cleaner with Power Nozzle - page 20
0 11) HOOVER and v@ are trademarks of THE HOOVER COMPANY, NORTH CANTON, OHIO 44720 12-91 S3399 Litho USA 56513-319 ...
¿Tienes una pregunta acerca de Hoover Canisfer Cleaner with Power Nozzle?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Hoover Canisfer Cleaner with Power Nozzle, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Hoover Canisfer Cleaner with Power Nozzle probablemente compartirá una forma de solucionarlo.