-
Regency I1200S - page 1
FPI FIREPLACE PRODUCTS INTERNA TIONAL L TD. 6988 V enture St., Delta, BC Canada, V4G 1H4 918-665a I1200S W ood Insert 07/12/07 Owners & Installation Manual T ested by: Installer : Please complete the details on the back cover and leave this manual with the homeowner . Homeowner: Please keep these instructions for future reference. www .regency- ...
-
Regency I1200S - page 2
I1200 Regency Wood Insert 2 Thank-you for purchasing a REGENCY FIREPLACE PRODUCT . The pride of workmanship that goes into each of our products will give you years of trouble-free enjoyment. Should you have any questions about your product that are not covered in this manual, please contact the REGENCY DEALER in your area. Keep those REGENCY FIRES ...
-
Regency I1200S - page 3
I1200 Regency Wood Insert 3 T ABLE OF CONTENTS SAFETY LABEL Safety Label .................................................................. 4 UNIT DIMENSIONS With Standard Flue Adaptor .......................................... 5 With Offset Flue Adaptor ............................................... 6 INST ALLA TION Before Installing your Insert ...
-
Regency I1200S - page 4
I1200 Regency Wood Insert 4 SAFETY LABEL This is a copy of the label that accompanies each I1200S Wood Insert . W e have printed a copy of the contents here for your review . LISTED F ACTORY BUIL T FIREPLACE INSERT CERTIFIED FOR USE IN CANADA AND U.S.A. MODEL: I1200S TESTED TO: ULC S628-M93 / UL 1482-1998 / ULC S627-00 / UL 737-2000 REPORT NO. 632- ...
-
Regency I1200S - page 5
I1200 Regency Wood Insert 5 UNIT DIMENSIONS WITH ST ANDARD FLUE ADAPTOR 6" (152mm) Diameter ST ANDARD FLUE ADAPTOR (171-932) ...
-
Regency I1200S - page 6
I1200 Regency Wood Insert 6 UNIT DIMENSIONS WITH OFFSET FLUE ADAPTOR 6" (152mm) Diameter OFFSET FLUE ADAPTOR (171-936) ...
-
Regency I1200S - page 7
I1200 Regency Wood Insert 7 INST ALLA TION CHIMNEY SPECIFICA TIONS Before installing, check and clean your chimney system thoroughly . If in doubt about its condi- tion, seek professional advice. Y our Regency Insert is designed for installation into a masonry fi replace that is constructed in accordance with the requirements of "The Standard ...
-
Regency I1200S - page 8
I1200 Regency Wood Insert 8 Clearance diagram for installations INST ALLA TION Side and T op facing is a maximum of 1.5" thick. Floor protection must non-combustible, insulative material with an R value of 1.1 or greater . * If the hearth extension is fl ush with the fl oor (F) it must extend 19.5" in front of the body face (E). Note: H ...
-
Regency I1200S - page 9
I1200 Regency Wood Insert 9 INST ALLA TION INST ALLING YOUR INSERT SAFETY NOTE: The insert is very heavy and will require two or three people to move it into position. The insert can be made a little lighter by removing the cast iron door by opening it and lifting it off its hinges. Be sure to protect your hearth extension with a heavy blanket or c ...
-
Regency I1200S - page 10
I1200 Regency Wood Insert 10 1) Positive Flue Connection with Cleanout INST ALLA TION 2) Direct Flue Connection with Cleanout 3a) Full Flue Liner (No Cleanout Required) Note: A c lean-out door is sometimes required, by your inspector , to be installed when either the Positive fl ue connection or Direct fl ue connection method is used. The use of ...
-
Regency I1200S - page 11
I1200 Regency Wood Insert 11 INST ALLA TION F ACEPLA TE, TRIM & OPTIONAL BOTT OM F ACEPLA TE & F AN SUPPORT INST ALLA TION Regular/Oversize Faceplate Installation: 1) Thread the black 1/4" x 3/4" long hex bolts into the faceplate mount- ing bracket as shown in Diagram 1, leaving them approximately 1/4" out. 2) Fasten the face ...
-
Regency I1200S - page 12
I1200 Regency Wood Insert 12 8) Measure the total height of the faceplate assembly and cut both the left and right side trim accordingly using a metal cutting blade. 9) Assemble the left and right side trim to the top trim using the trim clips provided as shown in Diagram 5. 10) Fit the trim assembly over the faceplate assembly . See Diagram 6. 11 ...
-
Regency I1200S - page 13
I1200 Regency Wood Insert 13 15) Cut the bottom edge of the fan support (using a metal cutting blade) to the length measured in step 14. 16) Remove the fan assembly from the ash lip of the insert and position the fan support to the bottom of the fan assembly . 17) Drill 4 x 5/32" holes to the underside of the fan assembly using the holes in th ...
-
Regency I1200S - page 14
I1200 Regency Wood Insert 14 Ground Fan Fan Ground Green Neutral Live White Fan Switch Manual/ Auto Switch Black Black High (Black) Low (Red) Black Fan Thermodisc (normally open) 120V AC 60 Hz INST ALLA TION F AN / BLOWER Blower / Fan Wiring Diagram Y our fan should only be installed once the unit is in place in order to prevent any damage to the f ...
-
Regency I1200S - page 15
I1200 Regency Wood Insert 15 BRICK FLUE BAFFLE & SECONDAR Y AIR TUBE INST ALLA TION The fl ue baffl e system located in the upper area of the fi rebox is removable to make cleaning your chimney system easier . The brick baffl es must be installed prior to your fi rst fi re. Smoke spillage and draft problems may occur if the baffl es are ...
-
Regency I1200S - page 16
I1200 Regency Wood Insert 16 INST ALLA TION FIRST FIRE When your installation is completed and in- spected, you are ready for your fi rst fi re. 1) Open draft control fully . 2) Open fi rebox door and build a small fi re using paper and dry kindling, wait a few minutes for a good updraft in the fl ue to establish the fi re. Leaving the door s ...
-
Regency I1200S - page 17
I1200 Regency Wood Insert 17 15) Do not store any fuel closer than 2 feet from your unit. 16) Do not burn salt drift wood as it will corrode your unit and void the warranty . 17) Do not strike or slam the glass door shut as this may cause the glass to break. 18) Do not operate the unit if the glass is broken or missing. Do not operate the unit if t ...
-
Regency I1200S - page 18
I1200 Regency Wood Insert 18 3) Only burn seasoned wood! Avoid burning wet or green wood. Seasoned wood has been dried at least one year . 4) A small hot fi re is preferable to a large smouldering one that can deposit creosote within the system. 5) Check the chimney at least twice a month during the burning season for creosote build-up. 6) Have ch ...
-
Regency I1200S - page 19
I1200 Regency Wood Insert 19 MAIN ASSEMBL Y Part # Description 850-141 Black Door - Complete 850-142 Gold Door - Complete 850-143 Nickel Accent Door - Complete 850-144 Gold Accent Door - Complete 2) 846-302 Glass - Replacement 4) 936-243 7/8" Adhesive T ape Gasket 5) 846-920 Glass Retainer Clips (set of 8) 6) * Screws - 1/4-20 x 3/8" 8) 9 ...
-
Regency I1200S - page 20
I1200 Regency Wood Insert 20 P ARTS LIST F ACEPLA TES Part # Description 171-920 Faceplate & T rim Set - Regular - Black 171-924 T rim Set - Regular Brass 171-922 Faceplate & T rim Set - Oversize - Black 171-926 T rim Set - Oversize Brass 171-928 Bottom Piece and Fan Support - Regular 171-930 Bottom Piece and Fan Support - Oversize 60) * Fa ...
-
Regency I1200S - page 21
I1200 Regency Wood Insert 21 P ARTS LIST FIREBRICK Part # Description 170-960 Complete Brick Set 70) * Brick Regular Full Size: 1-1/4" x 4-1/2" x 9" 76) * Brick Partial: 1-1/4" x 2" x 9" 81) * Brick Partial: 1-1/4" x 1-1/4" x 9" 84) * Brick Partial: 1-1/4" x 4-1/2" x 8" 85) * Brick Partial ...
-
Regency I1200S - page 22
I1200 Regency Wood Insert 22 NOTES ...
-
Regency I1200S - page 23
I1200 Regency Wood Insert 23 W ARRANTY Regency Fireplace Products are designed with reliability and simplicity in mind. In addition, our internal Quality Assurance T e am carefully inspects each unit thoroughly before it leaves our door . FPI Fireplace Products International Ltd. is pleased to extend this limited lifetime warranty to the original p ...
-
Regency I1200S - page 24
Printed in Canada Installer: Please complete the following information Dealer Name & Address: ______________________________________________ ___________________________________________________________________ Installer: ___________________________________________________________ Phone #: _________________________________________________________ ...
¿Tienes una pregunta acerca de Regency I1200S?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Regency I1200S, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Regency I1200S probablemente compartirá una forma de solucionarlo.