-
Hans Grohe 06061XX0 - page 1
Installation Instructions / W arranty C Cross 06063XX0 C Scroll 06062XX0 C Lever 06061XX0 Solaris² E 04146XX0 Allegro² E 04152XX0 Metro² E 04158XX0 Metris S 31316XX1 Focus S 31735XX1 T alis S 32316XX1 ThermoBalance I T rim Kits ...
-
Hans Grohe 06061XX0 - page 2
2 These instructions cover these models: V alve trim Shower set only trim C Lever 06061XX0 06079XX0 C Scroll 06062XX0 06080XX0 C Cross 06063XX0 06081XX0 Solaris² E 04146XX0 04149XX0 Allegro² E 04152XX0 04155XX0 Metro² E 04158XX0 04161XX0 Metris S 31316XX1 31323XX1 Focus S 31735XX1 31771XX1 T alis S 32316XX1 32323XX1 Solaris E 06635XX0 06641XX0 S ...
-
Hans Grohe 06061XX0 - page 3
3 T echnical Information Recommended pressure 45 - 72 psi Max hot water temperature 165 F* Recommended incoming hot water temp. 120° - 140° F* With rough valve 06621000, 06622000 Nominal capacity @ 45 PSI 9.5 gpm Nominal capacity @ 60 PSI 11.5 gpm With rough valve with bypass 06300000, 06301000 Nominal capacity @ 45 PSI 6.0 gpm Nominal capacity @ ...
-
Hans Grohe 06061XX0 - page 4
4 Insert the car tridge in the rough. The locator tab on the cartridge goes straight into the notch in the rough*. T urn on the water supplies. Grasp the stop unit portion of the car tridge and turn it. If there is a leak around the cartridge, tur n the supplies off, and remove the cartridge. Confir m that the sealing gasket from the flushing plug ...
-
Hans Grohe 06061XX0 - page 5
5 All other models: Install two Duotec strips directly on the carrier plate. Install the remaining two strips on the back of the escutcheon. Install the carrier plate gasket and carrier plate with the carrier plate screws. Press the escutcheon ver y firmly over the carrier plate, so that the strips of Duotec interlock, produc- ing a ver y firm hold ...
-
Hans Grohe 06061XX0 - page 6
6 Justify the handle T ools required: Thermometer 3 mm Allen wrench (included with trim kit) T urn the valve on. Place the ther mometer in the water stream. T urn the temperature control knob until the water coming out measures 100° on the thermometer . T urn the water off using the lever par t of the handle. Use a 3 mm Allen wrench to loosen the ...
-
Hans Grohe 06061XX0 - page 7
7 T roubleshooting User instructions The volume control lever controls the water flow . The center position is off. T urn the handle counter-clock- wise to send the water to the outlet port. The fur ther you turn the handle from the off position, the greater the water flow . Problem Possible Cause Solution W ater leaks between cartridge and rough s ...
-
Hans Grohe 06061XX0 - page 8
8 Remove the clip and stop ring from the thermostatic car tridge stem. Put them in a safe place. T urn the ther mostatic mixer stem with your fingers, clockwise to make the water cooler , counter-clockwise to make the water warmer . T urn the stem until the water coming out is the desired maximum high temperature – 110° in most areas. Reinstall ...
-
Hans Grohe 06061XX0 - page 9
9 Maintenance: Clean the filters Hold the stop unit still with one wrench. Use a second adjustable wrench or a 17mm deep socket wrench to unscrew and remove the thermostatic cartridge. Rinse the debris from the filters, using a soft tooth- brush if necessar y . Do not attempt to remove the screens. Lubricate the o-rings with white plumbers grease. ...
-
Hans Grohe 06061XX0 - page 10
10 Les instructions ci-après s’appliquent aux modèles suivants: Robinet mitigeur Ensemble de seulement douche C Lever 06061XX0 06079XX0 C Scroll 06062XX0 06080XX0 C Cross 06063XX0 06081XX0 Solaris² E 04146XX0 04149XX0 Allegro² E 04152XX0 04155XX0 Metro² E 04158XX0 04161XX0 Metris S 31316XX1 31323XX1 Focus S 31735XX1 31771XX1 T alis S 32316XX ...
-
Hans Grohe 06061XX0 - page 11
11 Données techniques Pression d’eau recommandée 45 - 72 psi T empérature maximum pour l’eau chaude 165° F* T empérature recommandée pour l’eau chaude 120° - 140° F* A vec corps d’encastrement 06621000, 06622000 Capacité nominale à 45 psi 9.5 gpm Capacité nominale à 60 psi 11.5 gpm A vec corps d’encastrement et dérivation 063 ...
-
Hans Grohe 06061XX0 - page 12
12 Insérez l’élément thermostatique dans la pièce intérieure. La languette s’insère directement dans la coche de la pièce intérieure. La tige de position au dos de l’élément thermos- tatique s’insère directement dans le trou de la pièce intérieure. Utilisez les vis du bouchon de rinçage pour fixer la plaque d’arrêt à la pi ...
-
Hans Grohe 06061XX0 - page 13
13 T ous les autres modèles (écusson rond) : Installez deux bandes Duotec direc- tement sur la plaque-support. Installez les deux autres bandes au dos de l’écusson. Installez la plaque-support et le joint à l’aide des vis de la plaque-support. Pressez fermement l’écusson sur la plaque- support. Les bandes Duotec se fixeront en place bien ...
-
Hans Grohe 06061XX0 - page 14
14 Réglage de la poignée Outils requis : Thermomètre Clé hexagonale 3 mm Ouvrez la valve. Placez le thermomètre dans le jet d’eau. T ournez le bouton de contrôle de la température jusqu’à ce que l’eau qui s’écoule atteigne 100° F . Fermez l’eau. À l’aide d’une clé hexagonale de 3mm, desserrez la vis de la poignée. Retirez ...
-
Hans Grohe 06061XX0 - page 15
15 Dépannage Problème Cause Possible Solution Fuites entre l’élément thermosta- tique et la pièce interieure Le joint du bouchon de rinçage est encoure à l’intérieur Enlevez le joint. Une ou des plaques de céramique de l’élément thermo- statique sont endommagées. Remplacez l’élément thermo- statique. La poignée tourne, mais l ...
-
Hans Grohe 06061XX0 - page 16
16 Retirez l’étrier et la bague de retenue de la tige de la cartouche ther mostatique. T ournez la tige du mitigeur thermostatique jusqu’à ce que la température de l’eau chaude atteigne le degré voulu – habituellement 110 °F . Réinstallez la bague de retenue de façon à ce qu’elle s’appuie sur la butée d’arrêt. Réinstallez l ...
-
Hans Grohe 06061XX0 - page 17
17 Lubrifiez les joints toriques avec de la graisse blanche de plomberie. T enez fermement le dispositif d’arrêt en place. Réinstallez et serrez la cartouche ther mostatique. Installez l’écusson. Réglez et installez la poignée. Replacement Parts 1 2 3 4 5 6 7 15 16 17 8 9 10 11 12 13 14 21 18 19 20 ...
-
Hans Grohe 06061XX0 - page 18
18 Cleaning Recommendation for Hansgrohe Pr oducts Modern lavator y faucets, kitchen faucets, and showers consist of ver y different materials to comply with the needs of the market with regard to design and functionality . T o avoid damage and returns, it is necessar y to consider cer tain criteria when cleaning. Cleaning Materials for Faucets and ...
-
Hans Grohe 06061XX0 - page 19
19 Limited Lifetime Consumer W arranty This product has been manufactured and tested to the highest quality standards by Hansgrohe, Inc. (“Hansgrohe”). This warranty is limited to Hansgrohe products which are purchased by a consumer in the United States after March 1, 1996, and installed in either the United States or Canada. WHO IS COVERED BY ...
-
Hans Grohe 06061XX0 - page 20
LENGTH OF W ARRANTY Replacement or repaired parts of products will be covered for the term of this warranty as stated in the following two sentences. If you are a consumer who purchased the product for use primarily for personal, family , or household purposes, this warranty extends for as long as you own the product and the home in which the produ ...
¿Tienes una pregunta acerca de Hans Grohe 06061XX0?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Hans Grohe 06061XX0, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Hans Grohe 06061XX0 probablemente compartirá una forma de solucionarlo.