Español dropdown-ico

Manual de instrucciones American Dynamics SpeedDome Ultra VI

34 de páginas 2.06 mb
Descargar

Pasar a la página of 34

Summary
  • American Dynamics SpeedDome Ultra VI - page 1

    SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 1 of 34 S peedDome ® Ultra VI Camera Domes Installation and Service Guide RAS816LS and RAS816WLS Series Figure 1. SpeedDome Ultra camera dome © 2005 Sensormatic Elect ronics Corp. Contents About this Guide .................................................... 1 About the Ca mer ...

  • American Dynamics SpeedDome Ultra VI - page 2

    SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 2 of 34 About the Camera Dome The SpeedDome Ultra VI camera dome (Figure 1) comes in black or white finish (to ble nd into surrounding areas), mou nts indoors or outdoors, and can communicate with the video controller over a SensorNet 485, RS-422, or Manchester network. The dome ...

  • American Dynamics SpeedDome Ultra VI - page 3

    SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 3 of 34 Figure 2. Mounting base and housing and eyeball assembly Standard Base Base with I/O Board Indoor Ceiling Mounting Using hardwa re shipped with the base, the dome attaches directly to indoor ceilings made of sheet rock, wood, metal, or concre te (Figure 3), or to tile ce ...

  • American Dynamics SpeedDome Ultra VI - page 4

    SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 4 of 34 Indoor Ceiling/Wall Mounting (Optional) The camera dome attaches to one of the following optional indoor mounting structures (Figure 5 ). Sheet Rock, Plaster or Wood Ceilings RHIUTH Top hat housing with trim ring This housing attaches to a ceiling or to most indoor mount ...

  • American Dynamics SpeedDome Ultra VI - page 5

    SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 5 of 34 Figure 5. Indoor mounting structures (option al) RHIUFB RHIUA B RHIUHC RHIU 2X2 RHIUTH RHIUTR RUCLR RUSLV RUSMK RUGLD RHIULWM RHIUC M RHIUWM RHPLA RHIU3X3 RHIU4X4 RH I UP NDT RHIUIB RHIU2X2P ...

  • American Dynamics SpeedDome Ultra VI - page 6

    SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 6 of 34 Outdoor Mounting (Optional) Note: This document doe s not include outdoor installation and service instructions. Fo r these instructions, see Insta lling the RHODUL Outdoor Housing, 8000-2573 -04. The camera dome attaches to outdoor wall s and ceilings using an RHODUL ou ...

  • American Dynamics SpeedDome Ultra VI - page 7

    SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 7 of 34 Figure 8. Outdoor mounting structures (optional) RHOTR over roof mount (shown with RHOTRF bracket) PHOPN pendant mount RHOWPA pole mount RHOSW/RHOLW wall mount RHOWCA corner bracket (shown with RHOLW mount) RHOSW RHOLW ...

  • American Dynamics SpeedDome Ultra VI - page 8

    SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 8 of 34 Dat a Cable Requirements Table 2 shows the data cable requirements for SensorNet, RS-422, and Manchester net works. For more information about communi cation protocols and cable networks, see Communication Protocols and Cable Networks, 8000-2573 -19. Table 2. Data cable ...

  • American Dynamics SpeedDome Ultra VI - page 9

    SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 9 of 34 Power-Up Routine After power is connected to the dome, the dome performs the following hom ing routine. 1. After a few seconds, the camera lens tilts up into the housing and eyeball assembly. 2. The lens tilts downs un til it looks at the floor. 3. Eyeball pans slowly. 4 ...

  • American Dynamics SpeedDome Ultra VI - page 10

    SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 10 of 34 W arnings and Cautions Please review the following warning s and cautions before you begin installation or service. WARNINGS ! WARNING! ALWAYS USE: • Proper safety equipment for the location and type of installation. • Proper lift equipment to reach the installation ...

  • American Dynamics SpeedDome Ultra VI - page 11

    SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 11 of 34  When using the standard b ase and wiring cables directly to the dome, ALWAYS connect the video cable to the dome before you conne ct the 9-pin cable (which contains power). If you connect the 9-pin cable first, you risk shorting delicate electronics near the con nec ...

  • American Dynamics SpeedDome Ultra VI - page 12

    SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 12 of 34 Connecting to the Standard Mounting Base This procedure explains how to conne ct the housing and eyeball assembly to a standard ba se. CAUTION: The maximum length of ca ble allowed between the Class 2 LPS (low voltage) ac source, such as a J-box, and the dome is 250m (8 ...

  • American Dynamics SpeedDome Ultra VI - page 13

    SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 13 of 34 4. Set termination jumper JW1 (Figure 12). Depending upon the dom e’s location in the communications lin e, set jumper JW1 across the appropriate pins as describe d in the following chart: Position of dome in communications line… Setting Pins Between other devices U ...

  • American Dynamics SpeedDome Ultra VI - page 14

    SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 14 of 34 6. Conne ct 4-pin plug (alarm input/output) t o 4-pin receptacle (Figure 13). a. Feed cable through access hole in base. b. Connect alarm wires to 4-pin plug (refer to chart be low). c. Insert plug into mating receptacle in top of housing and eyeball assembly. Alarm con ...

  • American Dynamics SpeedDome Ultra VI - page 15

    SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 15 of 34 8. Connect the housing and eyeball assembly to the base (Figure 14) by aligning the Cap and Base tabs and then turning clockwise until you hear a click. Figure 14. Connecting housing and eyeball assembly to base (cables and lanyard not sho w n) 9. Wait a few seconds for ...

  • American Dynamics SpeedDome Ultra VI - page 16

    SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 16 of 34 Figure 15. Electrical connections 1 P1 P4 P3 P8 P7 JW1 I/O BOARD JW1 Terminations FUNCTION Termi nated Unterminated PINS 1- 2 2- 3 Pin 1 Pin 1 Pin 1 Pin 1 4. Conne ct alarm output cable, if used, to P3 connector. Pin Color Desig nation 1 — 12Vdc (100mA max.) 2 — 12V ...

  • American Dynamics SpeedDome Ultra VI - page 17

    SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 17 of 34 Figure 16. Test switch/LEDs on I/O board Comm. LED Pow er LED RS422 Te st Pushbu tton 10. Set dome address (Figu re 17). Recessed at top of housing and eyeball assembly are three rotary address switches. Address range is from 001 to 255, excep t for Manchester, which is ...

  • American Dynamics SpeedDome Ultra VI - page 18

    SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 18 of 34 Using the Inst all/Removal T ool CAUTION: Do not use this tool to conne ct the dome to the standard base. Used only when the dome is connected t o a base having an I/O board, the RHIRT install/removal tool eliminates the need for a ladder during routine service. The too ...

  • American Dynamics SpeedDome Ultra VI - page 19

    SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 19 of 34 Figure 19. How to use the install/removal tool Skirt or Bubble Attachment/Detachment Dome Connection (reverse steps to disconnect) Do not use this tool to connect the standard base! Attachment Detach ment A B C Line up Line up B C D E Turn until you feel a click. Catch ...

  • American Dynamics SpeedDome Ultra VI - page 20

    SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 20 of 34 T roubleshooting Indoor Domes CAUTION: This troublesh ooting section is for indoor camera domes only! To trouble shoot outdoor domes, see install ation and service manual shipped with the outdoor h ousing. This chapter contains info rmation on: • Routine troubleshooti ...

  • American Dynamics SpeedDome Ultra VI - page 21

    SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 21 of 34 Procedure Follow steps until the problem is correct ed. 1. Check video on monitor (a, b, or c). a. No video? Go to step 2. b. Contrast or color off? YES Ship entire dome (base inc luded, if it contains an I/O board) back to the GSC. Place dust cover over spring finger c ...

  • American Dynamics SpeedDome Ultra VI - page 22

    SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 22 of 34 6. Observe green power LED on I/O board (Figure 21). Is green LED off or not on steady? YES Verify 24Vac cable is properly attached. If OK, replace I/O board or ship entire dom e to the GSC. NO Go to step 7. P7 Connector (AC in) Pin Color Desig nation 1 Black 24 Vac 2 R ...

  • American Dynamics SpeedDome Ultra VI - page 23

    SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 23 of 34 9. Check spring finger connector on I/O board by connecting housing an d eyeball assembly to original base to verify contact between spri ng fingers and CPU board (under cap ). Does dome produce video and respon d to commands? YES Spring fingers may not have seated prop ...

  • American Dynamics SpeedDome Ultra VI - page 24

    SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 24 of 34 Disassembling the Dome CAUTION: Once disa ssembled, parts of dome housing and eyeball assembly are "extremely fragile" and may break. Proceed usi ng extreme care! This section explains how to remove the following parts from the camera dome. • CPU board, page ...

  • American Dynamics SpeedDome Ultra VI - page 25

    SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 25 of 34 Removing the P/S Board CAUTION: Electrostatic-se nsitive device. Use a ground strap whe n handling power supply board. Referring to Figure 23. 1. Perform procedure "Removing the CPU Board" (page 27). 2. Remove metal shield. Remove three standoffs holding metal ...

  • American Dynamics SpeedDome Ultra VI - page 26

    SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 26 of 34 Removing the Slot Covers 1. Gently swivel eyeball to totally expose one of two slot covers (Figure 25). CAUTION: Swiveling fast can damag e gears. 2. Insert small, thin-bladed screwdriver into space between cover and eyeball. 3. Gently pry off slot cover. 4. Gently swiv ...

  • American Dynamics SpeedDome Ultra VI - page 27

    SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 27 of 34 Detaching the Eyeball 1. Perform pro cedure "Removing the Slot Covers" (page 29). 2. Perform pro cedure "Removing the Camera" (this page). 3. Detach eyeball from housing (Figure 28 ). a. Turn yoke to access tabs . One tab is more accessible than the ...

  • American Dynamics SpeedDome Ultra VI - page 28

    SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 28 of 34 The following steps refer to Figure 32. 6. Access camera/lens board. To do this, loosen captive retaining screw holding bearing assembly in place and remove this assembly. 7. Remove cabl es from camera/lens board. a. Small amber ribbon cable is from tilt motor. Unplug t ...

  • American Dynamics SpeedDome Ultra VI - page 29

    SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 29 of 34 6. Access tilt motor. To do this, loosen captive retaining screw holding tilt cable assembly in place and gently remove this assembly. 7. Remove tilt motor (Figure 35). Lift motor housing up as shown (1) to di sengage motor from tilt gear. Then pull motor bracket toward ...

  • American Dynamics SpeedDome Ultra VI - page 30

    SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 30 of 34 Illustrated Part s List This section helps you to identify parts that make up the base and housing and eyeball a ssembly. Parts in Table 3 are shown in Figure 37 . Note: Not all of the parts, which are shown for clarity, are orderable. Part s are subject to change based ...

  • American Dynamics SpeedDome Ultra VI - page 31

    SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 31 of 34 Figure 37. Base, housing, and eyeball assembly 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 20 21 22 23 24 25 26 33 27 28 29 30 31 32 40 39 38 37 36 34-35 Standard Base Assembly* Base Assembly with I/O Board** Housing Assembly (0400-1399-01/-02) Housing and Eyeball Ass ...

  • American Dynamics SpeedDome Ultra VI - page 32

    SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 32 of 34 Specifications-Indoor Dome Operational Pan/Tilt: Manual Pan S peed ............ 0.2°-100 ° per second (scaled to zoom position) Manual Tilt Speed ............. 0.25°-100° per second (scaled to zoom position) Preset Pan/Tilt Speed ....... 220° per second maximum Pan ...

  • American Dynamics SpeedDome Ultra VI - page 33

    SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 33 of 34 Lens and Bubble Densities Eyeball Lens ......................... f0 Bubbles: RUCLR (Clear ) .................. f0 RUSLV (Silver).................. f1.5 to f2 RUSMK (Smoke) .............. f0.5 RUGLD (Gold) .................. f1.5 to f2 Specifications-Out door Housing Ele ...

  • American Dynamics SpeedDome Ultra VI - page 34

    SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 34 of 34 Field-of-View Formulas: 3.2mm* x distance from camera (m) Focal length (mm) = Horizontal view (m) 2.4mm* x distance from camera (m) Focal length (mm) = Vertical view (m) * Horizontal scanning area of pi ckup device (mm) in camera. ** Vertical scanning area of pickup dev ...

Fabricante American Dynamics Categoría Security Camera

Los documentos del dispositivo American Dynamics SpeedDome Ultra VI que obtenemos del fabricante se pueden dividir en varios grupos. Entre ellos están::
- dibujos técnicos American Dynamics
- manuales de instrucciones SpeedDome Ultra VI
- hojas de producto American Dynamics
- folletos informativos
- o etiquetas energéticas American Dynamics SpeedDome Ultra VI
Todos son importantes, pero lo más importante desde el punto de vista del usuario de un dispositivo lo encontraremos en el manual de instrucciones American Dynamics SpeedDome Ultra VI.

Un conjunto de documentos determinado como manual de instrucciones se divide también en tipos más detallados, tales como: instrucciones de montaje American Dynamics SpeedDome Ultra VI, instrucciones de servicio, instrucciones cortas o instrucciones de usuario American Dynamics SpeedDome Ultra VI. Dependiendo de la situación debes buscar el documento que necesitas. En nuestra página puedes consultar el manual de instrucciones más popular del producto American Dynamics SpeedDome Ultra VI.

Manuales de instrucciones parecidos

El manual de instrucciones del dispositivo American Dynamics SpeedDome Ultra VI, ¿cómo debería ser?
El manual de instrucciones, también determinado como el manual de usuario o simplemente instrucciones, es un documento técnico que tiene como objetivo ayudar a los usuarios a utilizar American Dynamics SpeedDome Ultra VI. Las instrucciones normalmente las realiza un escritor técnico pero en un lenguaje comprensible para todos los usuarios de American Dynamics SpeedDome Ultra VI.

El manual de instrucciones completo de American Dynamics debe contener unos elementos básicos. Una parte de ellos es menos importante, como por ejemplo: la portada / la página principal o las páginas de autor. Sin embargo, lo demás debe facilitarnos la información más importante desde el punto de vista del usuario.

1. Introducción y pistas sobre cómo orientarse con el manual American Dynamics SpeedDome Ultra VI - Al principio de cada manual se deben encontrar las indicaciones acerca de la manera de usar un manual de instrucciones. Debe contener información sobre dónde encontrar el índice American Dynamics SpeedDome Ultra VI, preguntas frecuentes o problemas más comunes – son los apartados más buscados por los usuarios de cada manual de instrucciones.
2. Índice - listados de todos los consejos acerca de American Dynamics SpeedDome Ultra VI que encontraremos en el documento
3. Consejos de uso de las funciones básicas del dispositivo American Dynamics SpeedDome Ultra VI - que deben facilitarnos los primeros pasos durante el uso de American Dynamics SpeedDome Ultra VI
4. Troubleshooting - una secuencia sistematizada de acciones que nos ayudará a diagnosticar los problemas más importantes con American Dynamics SpeedDome Ultra VI
5. FAQ - las preguntas frecuentes
6. Datos de contacto Información acerca de cómo encontrar los datos de contacto del fabricante / servicio de American Dynamics SpeedDome Ultra VI en cada país si no somos capaces de solucionar el problema por nuestra cuenta.

¿Tienes una pregunta acerca de American Dynamics SpeedDome Ultra VI?

Utiliza el formulario que se encuentra abajo

Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con American Dynamics SpeedDome Ultra VI, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con American Dynamics SpeedDome Ultra VI probablemente compartirá una forma de solucionarlo.

Copia el texto de la imagen

Captcha
Nueva imagen

Comentarios (0)