-
Sanyo VCC-4594 - page 1
INSTRUCTION MANUAL VCC-4594 COLOR CCD CAMERA About this manual B efo re in st a ll in g a nd us in g th e ca m e ra, pl ea se re ad th is ma nu al carefully. Be sure to keep it handy for later reference. L53Z 4/ U S G B 20 01 , 4 , 2 ...
-
Sanyo VCC-4594 - page 2
Depending on the conditions of use, installation and environment, please be sure to make the appropriate settings and adjustments. If you need help with installation and/or settings, please consult your dealer. CONTENTS INFORMATION TO USER ....................................................................... 2 PRECAUTIONS ........................ ...
-
Sanyo VCC-4594 - page 3
INFORMATION TO USER Safety Guard THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THIS UNIT. WARNING: TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK , DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. This installation should be made by a qualified service person and should conform ...
-
Sanyo VCC-4594 - page 4
PRECAUTIONS In case of problem Do not use the camera if smoke or a strange odour comes from the unit, or if it seems not to function correctly. Disconnect the power cord immediately, and consult your dealer (or a Sanyo Authorized Service Centre). Do not open or modify Do not open the cabinet, as it may be dangerous and cause damage to the unit. For ...
-
Sanyo VCC-4594 - page 5
PARTS NAMES 1 Power indicator (POWER) Comes on when the power to the camera is on. 2 Video output connector (VIDEO OUT: BNC type) Connect this connector to a device such as a VCR or monitor with a VIDEO IN connector. 3 Manual color/black and white setting terminal (CONTROL) • G (ground) terminal • C (color) terminal • B (black and white) term ...
-
Sanyo VCC-4594 - page 6
PARTS NAMES 8 Flange-back lock screw 9 Lens mount cap The cap is installed to protect the lens mount section. Remove the lens mount cap before installing a lens (sold separately). F Flange-back adjustment lever (See page 7) G Camera installation bracket The bracket can be fixed at the top or bottom of the camera. When fixing the bracket, be sure to ...
-
Sanyo VCC-4594 - page 7
CONCERNING AUTO-IRIS LENSES DC type auto-iris lens A lens without amplifier circuit that operates only on a DC power source. In general, this type of lens is referred to as DC type coil lens or DC type non-amplifier lens. (Set the A.I. LENS switch to the DC position.) VIDEO type auto-iris lens A lens with amplifier circuit that operates on video si ...
-
Sanyo VCC-4594 - page 8
FLANGE-BACK ADJUSTMENT If the pick-up surface is not correctly positioned with relation to the lens focal point, the pictur e will be out of focus (in particular when using auto-iris power zoom lenses, sold separately). If that is the case, adjust the flange-back position as described below. 1 Using a + screwdriver, loosen the flange-back lock scre ...
-
Sanyo VCC-4594 - page 9
MOUNTING THE LENS Please use a DC type auto-iris lens (sold separately). Checking the lens mount Do not use a lens if length “ L ” is more than 5 mm. If not, that may damage the camera and prevent proper installation. 1 Remove the lens mount cap from the camera. 2 Install the auto-iris lens. CS mount type lens Carefully align the lens mount wit ...
-
Sanyo VCC-4594 - page 10
MOUNTING THE LENS Rewiring the lens cable in the lens iris plug 1 Prepare the lens cable. Cut the c able at the plug, then rem ove approx. 8 mm of t he cab le she ath a nd str ip abou t 2 mm fro m each wire. 2 Install the lens iris plug. Solder the cable to the pins following the correct pin layout (refer to the table and illustrations), then close ...
-
Sanyo VCC-4594 - page 11
CONNECTIONS Basic connection for monitoring or recording The peripheral devices (VCR, monitor, lens, etc.) and cables are sold separately. 1 Make the video signal connection between the camera and the monitor or time lapse VCR. 2 Connect to 24 V AC UL listed class 2 power supply. CAUTION: • To prevent camera and/or power supply failure, pay close ...
-
Sanyo VCC-4594 - page 12
SETTINGS The illustration shows the factory default settings for the switches in the camera setup section. The camera settings are described on the assumption that a DC type auto iris lens is being used. If you are using a VIDEO type auto iris lens, be sure to read the Note which is given. Furthermore, refer to the sticker on the inside of the cove ...
-
Sanyo VCC-4594 - page 13
SETTINGS Iris function setting This should normally be set to the down ( AI ) position. Use a manual or fixed iris lens and set the lens aperture to the shortest F stop. Set the switch 1 ( IRIS ) to the up ( EI ) position. ☞ When using an auto-iris lens (for indoor/outdoor use) Set the switch 1 ( IRIS ) to the down ( AI ) position. Note: • The ...
-
Sanyo VCC-4594 - page 14
SETTINGS Backlight compensation setting This camera has two different backlight compensation functions: Normally backlight compensation switch 3 ( MULT ) and 4 ( CENT ) are set to the down ( OFF ) position. Change the backlight compensation switch settings depending on the conditions. • MULT mode: Use this position when applying backlight compens ...
-
Sanyo VCC-4594 - page 15
SETTINGS White balance adjustment Normally the switch 5 ( WB ) is set to the down ( ATW : auto white balance) position and the white balance is adjusted automatically. If a manual white balance adjustment is necessary, follow the steps below. Set the switch 5 ( WB ) to the up ( M : manual) position, then adjust the colour. • Turn RED (VR302) to s ...
-
Sanyo VCC-4594 - page 16
SETTINGS Lens iris adjustment If using a DC type auto-iris lens, you will need to set the LEVEL (VR301) volume when shooting in the conditions described below. L (counterclockwise): To decrease the contrast H (clockwise): To increase the contrast • If shooting simultaneously in a dark room and through a bright window. • If the subject backgroun ...
-
Sanyo VCC-4594 - page 17
SETTINGS Manual color/black and white setting Connect each pin of the CONTROL terminal as indicated below, to set the image to black and white or color as desired. • Color image setting Connect the C (color) and the G (ground) pins. • Black and white setting Connect the B (black and white) and the G (ground) pins. CONTROL terminal Image CB OFF ...
-
Sanyo VCC-4594 - page 18
SPECIFICATIONS Camera: Scanning system : NTSC standard TV system (525 TV lines, 30 frames/sec.) Interlace : PLL 2:1 interlace Image device : 1/3 inch solid state image device CCD Picture elements : 811 (H) x 508 (V) Effective picture elements : 768 (H) x 494 (V) Synchronizing system : Internal sync, Line lock manually switchable Resolution : 520 TV ...
-
Sanyo VCC-4594 - page 19
SANYO INDUSTRIAL VIDEO COLOR VIDEO CAMERA LIMITED WARRANTY OBLIGATIONS In order to obtain warranty service, the product must be delivered to and picked up from an Authorized Sanyo Service Center at the user’s expense, unless specifically stated otherwise in this warranty . The names and addresses of Authorized Sanyo Service Centers may be obtaine ...
-
Sanyo VCC-4594 - page 20
1AC6P1P2420-- L53Z4/US(0401KP-DSP) 21605 Plummer Street, Chatsworth, California 91311 Printed in Japan L53Z 4/ U S G B 20 01 , 4 , 2 ...
¿Tienes una pregunta acerca de Sanyo VCC-4594?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Sanyo VCC-4594, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Sanyo VCC-4594 probablemente compartirá una forma de solucionarlo.