-
Toa C-CV44-3 NTSC - page 1
Thank you for purchasing TOA’s Outdoor Color Camera. Please carefully follow the instructions in this manual in order to ensure long, trouble-free use of your color camera. OUTDOOR COLOR CAMERA C-CV44-3 NTSC C-CV44-3 P AL INSTR UCTION MANU AL ...
-
Toa C-CV44-3 NTSC - page 2
2 T ABLE OF CONTENTS 1. SAFETY PRECA UTIONS ................................................................................ 3 2. GENERAL DESCRIPTION ............................................................................. 4 3. HANDLING PRECA UTIONS .......................................................................... 4 4. NOMENCLA TURE . ...
-
Toa C-CV44-3 NTSC - page 3
3 1. SAFETY PRECA UTIONS • Before installation or use, be sure to carefully read all the instructions in this section in order to ensure long, trouble-free operation. • Be sure to follow all the precautionary instructions in this section, which contain important warnings regarding safety. • After reading, keep this manual handy for future ref ...
-
Toa C-CV44-3 NTSC - page 4
4 2. GENERAL DESCRIPTION The TOA C-CV44-3 is an outdoor-use high-resolution camera equipped with a 1/4” CCD. Its water-resistant design permits it to be mounted to outdoor walls or ceilings with no need to protect it from rain and the elements. Because the camera angle can be freely moved, a wide range of subjects can be monitored, regardless of ...
-
Toa C-CV44-3 NTSC - page 5
[Figure showing the camera from which the sunshade, front cover, and mounting bracket have been removed] [External View] 5 IRIS LH O FF O N F.ADJ BLC SHUTTER MONITOR OUT 1/60 1/100 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 4. NOMENCLA TURE (1) V ari-focal lens (2) Sunshade (3) Front co ver (4) Mounting bracket (standard accessory) (5) Security wire en ...
-
Toa C-CV44-3 NTSC - page 6
6 Camera mounting bolt Wa sher-installed M8 x 14mm hex bolt (standard accessor y) Security wire entr y hole Brack et mounting bolt (M8 or W 3/8) 120º ø50 mm 12 mm 96 mm 97.6 mm 70 mm 76 mm 4 -ø6.5 mm ø10.5 mm Used in mounting e xamples 1 and 2. Used in mounting e xample 3. 5. INST ALLA TION AND CONNECTIONS [Ceiling mounting example] [W all moun ...
-
Toa C-CV44-3 NTSC - page 7
7 Up Down Female-thread anchor M8 or W 3/8 Ceiling Mounting bracket Plain washer Bracket mounting bol t M8 or W 3/8 Spring washer Bracket mounting bolt M8 or W 3/8 Female-thread anchor M8 or W 3/8 Ceiling Mounting bracket Anti-rotation screw (such as self-tapping screws) Plain washer Spring washer [Mounting Example 1] Ceilings or walls [Mounting Ex ...
-
Toa C-CV44-3 NTSC - page 8
8 UL1095#22 Black/ White (Nonpolar) BNC jack Camera Input/ Out p ut terminal Cable joint section BNC plug Supplied cable Lock screw Connects to monitor Connector (water-resistant type) Water-resistant cap Connects to power supply source Insulation washers are attached to the mounting bracket. Mounting bracket Camera mounting bolt Washer-installed M ...
-
Toa C-CV44-3 NTSC - page 9
9 Camera Input/Output terminal Monitor : BNC plug 24 V AC or 12 V DC Video output Use the external power supply unit of the following rating when the camera is operated on 12 V DC. 12 V DC, over 1.0 A Video input Fit the watertight cap (shaded section) securely to the camera. 5. Mount the water-resistant cap to the camera. Note: If there is a gap b ...
-
Toa C-CV44-3 NTSC - page 10
10 Loosen the two sunshade fixing screws. Pull out the sunshade after rotating. Turn the front cover in the direction indicated by the arrow to remove. Front cover 6. ADJUSTMENT 1. Detach the sunshade and front cover after completing camera mounting and connections. [Removing the sunshade] [Removing the front cover] 2. Connect the Monitor output te ...
-
Toa C-CV44-3 NTSC - page 11
11 Mode setting switch Horizontal angle ± 60º Camera mounting bolt IR I S H L O F F O N BLC F . A D J SHUTTER 1/60 1/100 Vertical angle: 90º (In the case of ceiling mounting) Bracket mounting bolt Focus ring Zoom ring Iris control Picture tilting: ± 90º (Rotate the shaded section) Projection 5. Adjust the camera angle. • The camera angle can ...
-
Toa C-CV44-3 NTSC - page 12
12 Sunshad e After inserting, rotate the sunshade clockwise until it stops (as shown in the figure), then secure with the sunshade fixing screws. Sunshade fixing screw (washer-installed M3 x 8mm pan head screw) Slot for sunshade fixing screw insertion Sunshade fixing screw 9. Insert the sunshade from the front of the camera, as shown in the figure ...
-
Toa C-CV44-3 NTSC - page 13
13 OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON 7. ABOUT THE MODE SETTING SWITCH Set the Mode Setting switch for the best possible picture reproduction depending on installation conditions. 7.1. Adjustment Switch Set this switch when adjusting the lens focus. (Provides the same effect as when using the ND filter.) Standard position : Set to OFF after ...
-
Toa C-CV44-3 NTSC - page 14
14 Remedy Connect correctly. Solder correctly. Adjust the lens. Wipe the lens. Adjust correctly by following the instructions in the instruction manual for the monitor. Set the Adjustment switch of the Mode setting switch to the ON position, then focus the lens again. (Refer to Step 6 on p. 11.) Be sure to shift the Adjustment switch back to the OF ...
-
Toa C-CV44-3 NTSC - page 15
15 The specifications of this camera are subject to change without notice. • Accessories Mounting bracket ................................................................................ 1 Cable with water-resistant cap (2 m) .................................................. 1 Camera mounting bolt ................................................ ...
-
Toa C-CV44-3 NTSC - page 16
Printed in Vietnam 133-12-875-4F ...
¿Tienes una pregunta acerca de Toa C-CV44-3 NTSC?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Toa C-CV44-3 NTSC, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Toa C-CV44-3 NTSC probablemente compartirá una forma de solucionarlo.