-
AMT Datasouth 4000 - page 1
Fastmark 4000 Series Barcode Label Printer User ’ s Guide Part No. 110121 A ...
-
AMT Datasouth 4000 - page 2
User's Guide 1 IMPORTANT SAFETY INSTRUCTIONS AND OTHER NOTICES n This label printer complies with the requirements in Part 15 of FCC rules for a Class A computing device. Operation of this equipment in a residential area may cause unacceptable interface to radio and TV reception, requiring the operator to take whatever steps are necessary to c ...
-
AMT Datasouth 4000 - page 3
2 User's Guide CONVENTIONS Some of the procedures in this guide contain special notices that highlight important information: Note Indicate information that you should know to help your printer run properly and efficiently. Caution Indicate guidelines that, if not followed, can cause damage to equipment. Warning Indicate a situation where ther ...
-
AMT Datasouth 4000 - page 4
User's Guide 3 Table of Contents PRODUCT DESCRIPTION ....................................................................................... 7 OVERVIEW 8 UNPACKING AND INSPECTION ............................................................................ 9 INSTALLATION AND CONFIGURATION ........................................................ ...
-
AMT Datasouth 4000 - page 5
4 User's Guide Appendix A: Printer Specifications ........................................................................... 75 General Specifications .............................................................................................. 75 Fonts, Bar Codes and Graphics ................................................................. ...
-
AMT Datasouth 4000 - page 6
User's Guide 5 Table of Figures Figure 1 - Fastmark 4000 Series Printer .............................................................................. 7 Figure 2 - Model and Serial Number Location ..................................................................... 8 Figure 3 - Shipped with Printer ............................................ ...
-
AMT Datasouth 4000 - page 7
6 User's Guide This page is blank ...
-
AMT Datasouth 4000 - page 8
User's Guide 7 PRODUCT DESCRIPTION This label printer is a high-performance, low-cost Direct Thermal/Thermal Transfer labeling system. Its user-friendly design and affordable price set a new standard for the Desktop Label Printer in retail, office and industrial applications. The printer is designed with the most efficient memory management te ...
-
AMT Datasouth 4000 - page 9
8 User's Guide OVERVIEW The Fastmark FM4000 series is currently comprised of 3 models: • FM4402 • FM4602 • FM4603 While these models are similar in many ways, important differences exist. Throughout this manual instructions and illustrations applying to a particular model will be labeled accordingly otherwise the instructions apply to al ...
-
AMT Datasouth 4000 - page 10
User's Guide 9 UNPACKING AND INSPECTION This section is provided to assist you in taking the printer from the shipping container to the application environment and ready for use. 1. Remove top foam packing piece. 2. Lift printer straight up out of box carefully with adequate assistance. 3. Remove accessory kit and supplies. 4. Remove printer f ...
-
AMT Datasouth 4000 - page 11
10 User's Guide INSTALLATION AND CONFIGURATION Setting up the Printer Before setting up the printer you should first consider the following: • Flat stable surface with sufficient clearance to allow for interface cables and media loading. • Free from excessive direct sunlight, temperature, humidity, dust, dirt, and debris. • Near a ground ...
-
AMT Datasouth 4000 - page 12
User's Guide 11 Figure 5 - FM 4402 Back Panel Figure 6 - FM 4602 and 4603 Back Panel Model No. and Serial No. External Label Feed Slot Cover Parallel Port Serial Port AC Inlet Receptacle Power Switch AC Voltage Select Switch Model No. and Serial No External Label Feed Slot Cover PS/2, Keyboard Interface Switches Parallel Port Serial Port AC In ...
-
AMT Datasouth 4000 - page 13
12 User's Guide Connecting the Power Cord 1. Ensure printer Power Switch is off "0". 2. IMPORTANT: (FM4402 ONLY) Ensure the AC Voltage Select Switch is set to the correct Voltage for this installation. 3. Remove the yellow voltage setting label from the AC Inlet Receptacle . 4. Connect the power cord to the AC Inlet Receptacle locate ...
-
AMT Datasouth 4000 - page 14
User's Guide 13 Connecting the Printer to Your Host 1. You can connect the printer with any standard Centronics cable to the parallel port of the host computer. 2. Or, you can connect the printer with a serial cable to the RS-232C port of your computer or terminal. (For PC compatibles, the RS-232C port is COM1, COM2 or COM3.) Note : U sing Cen ...
-
AMT Datasouth 4000 - page 15
14 User's Guide The factory default parameters of serial port are: Speed (baud rate) 9600 Data format 1 start bit, 8 data bits and1 stop bit. Parity None Handshaking (Flow control) XON/XOFF as well as RTS/CTS Note: It is not necessary to set a switch or send a command for the parallel and serial port selection. The printer automatically detect ...
-
AMT Datasouth 4000 - page 16
User's Guide 15 Loading the Ribbon Thermal Transfer Media only If Direct Thermal Media is used, skip to the section Loading Media. 1. Open the Media Access Cover by lifting it up until it rests upon the top of the printer. 2. Open the Front Access Door by rotating it down. Figure 9 - Open Media Access Cover Media Access Cover Front Access Door ...
-
AMT Datasouth 4000 - page 17
16 User's Guide 3. Rotate the Green Printhead latch counter-clockwise to open the printhead module. 4. Rotate the Side Access Door down to allow the ribbon to be loaded under the printhead module. This will allow you to slide the ribbon under the printhead without having to thread it under the module. Figure 10 - Printhead Latch and Side Acces ...
-
AMT Datasouth 4000 - page 18
User's Guide 17 6. Place the Ribbon Take-up core on the Ribbon Take-Up Spindle located towards the front of the printer. 7. Slide both cores completely towards the center of the printer. 8. Route the ribbon under the print mechanism. 9. Important: Route ribbon under and around back of Ribbon Take-Up Core before attaching using tape or adhesive ...
-
AMT Datasouth 4000 - page 19
18 User's Guide 12. Verify if the printer is set for Thermal Transfer Mode: a. To verify the FM4402 printer print a self-test. If the printer is not set for Thermal Transfer mode, it can be set by using the Windows drivers, Utility Software, or sending the appropriate printer commands via the host. b. To verify the FM4602 and FM4603 printers a ...
-
AMT Datasouth 4000 - page 20
User's Guide 19 Loading Media 1. Fully open Media Access Cover . 2. Open the Front Access Door by rotating down. Figure 13 - Open Media Access Cover Media Access Cover Front Access Door Media Supply Spindle Media Supply Guide ...
-
AMT Datasouth 4000 - page 21
20 User's Guide 3. Rotate the green Printhead Latch counterclockwise to open the printhead. 4. Rotate the Side Access Door down to allow the media to be loaded under the printhead module. Figure 14 - Printhead Latch and Side Access Cover 5. Slide the Media Supply Guide to the full widest position. 6. Ensure the media is face out with the label ...
-
AMT Datasouth 4000 - page 22
User's Guide 21 10. Slide the green Outside Media Guide off the Front and Back Media Rails by pulling straight out. Figure 15 - Outside Media Guide 11. Thread the media over the Back Media Rail and under the Front Media Rail . 12. Continue feeding the media through the black Upper and Lower Media Sensor Arms located under the print module. 13. ...
-
AMT Datasouth 4000 - page 23
22 User's Guide 15. Grasping the Sensor Adjust Knob and sliding in or out as needed can move the Media Sensor. This is required only if the sensor must be moved to a specific location on the label to detect a notch (hole) or gap. Figure 16 - Media Sensor Adjust Knob 16. Important: To ensure proper media feeding and sensor operation, complete t ...
-
AMT Datasouth 4000 - page 24
User's Guide 23 Figure 17 - Media Routing 17. Rotate the Side Access Door up to close. 18. Rotate the green Print Head Latch clockwise fully to lock the printhead and Side Access Door shut. Upper Media Sensor Arm Lower Media Sensor Arm Front Media Rail Back Media Rail Media ...
-
AMT Datasouth 4000 - page 25
24 User's Guide Changing Position of the Media Supply Spindle The printer can store under the Media Access Cover an 8-inch outer diameter media roll that is wound on either 1.5 inch or 3 inch inner cores. When the Media Access Cover is closed touching on either the Media Cover or the bottom of the printer could cause unnecessary drag on the fo ...
-
AMT Datasouth 4000 - page 26
User's Guide 25 Calibrating Media Sensors Important: The first time media is installed, the Media Sensors must be calibrated. After the first calibration no further calibration is required unless the media type (length, color, backing material, etc.) is changed or irregular feeding occurs. 1. Ensure the printer is powered off. 2. Verify that t ...
-
AMT Datasouth 4000 - page 27
26 User's Guide Performing the Self Test 1. Power off the printer. 2. Make sure that 4 inch wide media is installed. The Self-test will print the maximum width of the installed label. 3. Press and hold the FEED/Config button. 4. Power on the printer. 5. Release the FEED/Config button when: a. FM 4402: The printer begins feeding labels. b. FM 4 ...
-
AMT Datasouth 4000 - page 28
User's Guide 27 Self Test Pattern for FM4602/FM4603 PPLA Figure 19 - Self Test FM4602/FM4603 PPLA ...
-
AMT Datasouth 4000 - page 29
28 User's Guide Self Test Pattern for FM4602/FM4603 PPLB Figure 20 - Self Test FM6402/FM4603 PPLB ...
-
AMT Datasouth 4000 - page 30
User's Guide 29 Self Test Pattern for FM4402 PPLA Figure 21 - Self Test FM4402 PPLA ...
-
AMT Datasouth 4000 - page 31
30 User's Guide Self Test Pattern for FM4402 PPLB Figure 22 - Self Test FM4402 PPLB ...
-
AMT Datasouth 4000 - page 32
User's Guide 31 Resetting the Printer to Factory Default Settings To reset the printer to its factory defaults after certain commands have been sent or settings changed: 1. Power off the printer. 2. Press and hold the CANCEL/RESET button. 3. Power on the printer. 4. As the printer turns on the printer will: FM 4402: All the LED's will com ...
-
AMT Datasouth 4000 - page 33
32 User's Guide This is a blank page ...
-
AMT Datasouth 4000 - page 34
User's Guide 33 PANEL OPERATION Front Panel The front panel includes - 3 LED indicators (READY, MEDIA and RIBBON) - 3 buttons (FEED, PAUSE and CANCEL) - LCD display ( for FM4602 and FM4603 models only ) Figure 23 - Fastmark 4000 Series Front Panel ...
-
AMT Datasouth 4000 - page 35
34 User's Guide L E D Indicators There are three LED indicators on the front panel, “READY”, “MEDIA” and “RIBBON”. These indicators display the present status of the printer. X READY The Ready LED indicates the following conditions: ON - The printer's powered is on. Off - The printer's power is off. Blinking - Error condi ...
-
AMT Datasouth 4000 - page 36
User's Guide 35 Button s Depending upon the printer model and current mode, the Front Panel buttons serve multiple functions. Refer to the following tables for their specific functions. Pressed and held down during Power UP Upon completion of the desired function the printer will go into a READY condition. Button Function m FEED The printer pe ...
-
AMT Datasouth 4000 - page 37
36 User's Guide Pressed during normal operation Button Function m FEED The printer will Feed a one label. m PAUSE The printer will begin blinking the READY LED. If printing the printer will STOP printing, and the READY LED will blink. If pressed a second time the printer will resume normal operation. The FM4602/4603 models will blink the READY ...
-
AMT Datasouth 4000 - page 38
User's Guide 37 LCD Display (FM4602 and 4603 models only) For the model FM4602/FM4603 the front panel is equipped with a 2 row by 16 character LCD display. The basic function of the display is: - Display the printer status - Display the printer settings - Display's prompts requesting input data from a keyboard or barcode reader. - Standar ...
-
AMT Datasouth 4000 - page 39
38 User's Guide With Barcode Reader Option If a barcode reader is connected and switches 6 through 8 are in the ON positions, the displayed message will be. READY (203,PPLA) WITH B.C. READER Abnormal Conditions If any abnormal condition occurs the related message will be displayed. For example: RIBBON OUT ...
-
AMT Datasouth 4000 - page 40
User's Guide 39 Front Panel Set-up Menu FM 4602 and FM 4603 models only The Set-up menu is a list of printer features that affect the basic operation of the printer. These are functions that can not normally be selected using software commands. Value settings that are changed using the keypad are stored into E2PROM and are retained when power ...
-
AMT Datasouth 4000 - page 41
40 User's Guide Procedure to Enter into Set-up Mode FM 4602 and FM 4603 models only 1. Power on the printer. 2. When the “ READY ” message is displayed on the LCD, press [ PAUSE ] and the [ CANCEL ] buttons simultaneously. Figure 24 - Entering into Set-up Mode 3. Press [ PAUSE ] button to scroll to the feature that you want to change. 4. P ...
-
AMT Datasouth 4000 - page 42
User's Guide 41 Set-up Mode Selection Items Item Range Factory Default Remarks CUT/PEEL POS (mm) + 015 to + 015 0 mm Controls cut and peeling position. PRINT OFFSET (mm) + 015 to - 008 0 mm Controls start vertical print position. Positive value only. TPH VER OFFS(mm) + 003 to - 003 0 mm RECOVERY PRINT ENABLE DISABLE ENABLE 1 GAP HEIGHT MORE TH ...
-
AMT Datasouth 4000 - page 43
42 User's Guide Notes: 1. To verify that a feature has been properly changed, cycle power on the printer. 2. Make sure the settings you desire has an * character by the value. 3. When changing the Media Sensor Type feature (Reflective and See-through); be aware that the See-through sensor is 1 mm to the left of the Reflective sensor. 4. If gra ...
-
AMT Datasouth 4000 - page 44
User's Guide 43 Setting Display Language The printer can display messages, error condition, and feature menus in multiple languages. This capability does not affect the printed text. The printer 's LCD display supports six languages : English, French, German, Italian, Spanish and Portuguese To change the currently displayed language 1. Pr ...
-
AMT Datasouth 4000 - page 45
44 User's Guide Back Panel The rear panel includes - An 8-bit DIP switch (FM4602/FM4603 models only) - A 36-pin Centronics connector - A 9-pin serial connector - A PS/2 keyboard connector (FM4602/FM4603 only) - A power switch and power connector Caution: On the FM4402 model there is a voltage selection switch for selecting the appropriate line ...
-
AMT Datasouth 4000 - page 46
User's Guide 45 FM 4602/4603 Figure 25 - Back Panel FM4602/FM4603 FM 4402 Models Figure 26 - Back Panel FM4402 Model Number and Serial number External Label Feed Slot Cover Parallel Port Serial Port AC Inlet Receptacle Power Switch Voltage Selection Switch Model Number and Serial number External Label Feed Slot Cover PS/2, Keyboard Interface B ...
-
AMT Datasouth 4000 - page 47
46 User's Guide Back Panel Switches (FM4602 and FM4603 models only) Back Panel Switches are only available on FM4602 and FM4603. Any change in switch position is not registered until Power is cycled. Standard Switch Settings Switch Number Function Position setting Description ON Ribbon is installed. Thermal transfer mode. Enables end-of-ribbon ...
-
AMT Datasouth 4000 - page 48
User's Guide 47 Switches 6, 7 and 8 are used to determine the printer's Baud Rate. 6 7 8 Baud rate OFF OFF OFF 9600 (default) ON OFF OFF 2400 OFF ON OFF 4800 ON ON OFF 19200 OFF OFF ON 38400 ON ON ON Special Setting: 9600 and for barcode reader Special Switch Settings: Switch number 1 2 3 4 5 6 7 8 Special Condition Sets Baud Rate to 9600 ...
-
AMT Datasouth 4000 - page 49
48 User's Guide PS/2 Keyboard I/F (FM4602 and FM4603 models only) The special keyboard interface connector is available on the FM4602/FM4603 models. This is for PS/2 keyboard or barcode reader with keyboard wedge. When this interface is used, using the Centronics or RS-232 communication ports is discouraged. Use of the PS/2 keyboard interface ...
-
AMT Datasouth 4000 - page 50
User's Guide 49 COMMAND QUICK REFERENCE This section lists all software commands of the printer. For more information please refer to the Programmer’s Manual . Command Set for PPLA The following commands are for Printer Programming Language A. Note: In this quick reference all variable data is represented in Italics. System Setting Commands ...
-
AMT Datasouth 4000 - page 51
50 User's Guide Interaction Commands Such commands only apply to the serial port and allow the host to understand the status and configuration of the printer. Command Description Response from printer Contents of the Response <SOH># Reset Yes <XOFF><XON>T <SOH>A Send a readable status string Yes <8 bytes, Y/N> < ...
-
AMT Datasouth 4000 - page 52
User's Guide 51 System Level Commands Command Description Remarks <STX>a Enable page/job echo characters <STX>c xxxx Set continuous paper length and disable edge sensor <STX>D xxxxxxx Memory dump** xxxxxxx : memory address in HEX value <STX>E xxxx Set copy count for stored label <STX>e Enable edge sensor <STX&g ...
-
AMT Datasouth 4000 - page 53
52 User's Guide Formatting Commands Command Description : xxxx Set cut amount A n Set print mode n : ‘1’- exclusive, ‘2’ - transparent C xxxx Set horizontal offset c xx Set cut amount D wh Set pixel width and height E Form feed and return to system level command mode G Store previous data to global register <STX>S n Retrieve from ...
-
AMT Datasouth 4000 - page 54
User's Guide 53 Editing Commands Command structure Command function R thveeeyyyyxxxx <string><CR> Printing text and bar codes Components of command Description Variables R print direction ‘1’,’2’,’3’ or ‘4’ (rotation) t: object type ‘0’ ~ ‘9’ and ‘:’ (fonts) ** , ‘A’ ~ ‘Z’ and ‘a’ ~ ‘z’ ( ...
-
AMT Datasouth 4000 - page 55
54 User's Guide Object Command Structure Description L : line (if t is ‘X’) L wwwhhh www : width, hhh : height. L : line (if t is ‘X’) l wwwwhhhh wwww : width, hhhh : height. B : box (if t is ‘X’) B aaabbbcccddd aaa : horizontal width bbb : vertical height ccc : thickness of top and bottom edges ddd : thickness of left and right ba ...
-
AMT Datasouth 4000 - page 56
User's Guide 55 Font Downloading Commands Such commands are only used for soft fonts with PCL format. Command Description ESC*c###D assign the soft fonts ID number (### : 100 ~ 999) ESC)s###W download font descriptor (### : length of font descriptor) ESC*c###E set character code (### : 1 ~ 255) ESC(s###W download character descriptor and image ...
-
AMT Datasouth 4000 - page 57
56 User's Guide This is a blank page. ...
-
AMT Datasouth 4000 - page 58
User's Guide 57 Command Set for PPLB The following commands are for Printer Programming Language B. All PPLB commands must be ended with <LF> or <CR>+<LF> codes. No spaces are allowed between parameters and leading command character. Command Description Parameter A x,y,rot,font,hm,vm,nr,string Print text. font : 1 to 5 for in ...
-
AMT Datasouth 4000 - page 59
58 User's Guide Command Description Parameter JB JF Disable back feed** Enable back feed** LE x , y,hlen,vlen Line draw by exclusive hlen: horizontal length vlen: vertical length LO x , y,hlen,vlen Line draw by OR LW x , y,hlen,vlen Draw white line N Clear frame buffer O[,C][,N][,D] Select options P p1[,p2] Print label p1: label set number p2: ...
-
AMT Datasouth 4000 - page 60
User's Guide 59 Command Description Parameter d1, hadj Set horizontal position adjustment** hadj: adjustment in dots. d2, hadj Set horizontal position adjustment same as d1, except it is no saved to E2PROM Notes: 1. x and y represent horizontal and vertical coordinate values. 2. hm and vm stand for horizontal and vertical multipliers. 3. rot i ...
-
AMT Datasouth 4000 - page 61
60 User's Guide This is a blank page. ...
-
AMT Datasouth 4000 - page 62
User's Guide 61 PRINTER DRIVER The bundled printer driver is used for applications under Windows 95/98/2000 and Windows NT. You may run any popular software application, such as MS-Word, as long as they are for Windows and printing the contents to the printer through the designated driver. Before starting installation you should: ♦ Check the ...
-
AMT Datasouth 4000 - page 63
62 User's Guide Driver Installation ♦ Windows needs to be running. ♦ Insert the appropriate printer driver diskette into the floppy disk drive. 1. Click the “Start” button. 2. Select “Settings”, then “Printers” 3. Double click the “Add Printer” icon. 4. At the Add Printer Wizard, Click “Next”. 5. Specify the “Network? ...
-
AMT Datasouth 4000 - page 64
User's Guide 63 How to Use the Driver After the driver is installed, you can open the Printer's dialogue box and make parameter settings: Windows 95/98/2000/NT4.0 - Start é Settings é Printers é Printer Name é Properties Parameter setting: After entering the Selected Printer you can change the parameters to meet your configuration and ...
-
AMT Datasouth 4000 - page 65
64 User's Guide Details Tab Print to the following port This allows you to select the IO port to link with the printer. The port may be one of parallel (LPT), serial (COM), network port or file. If the communication port is the serial port (COM1: or COM2 :), check the baud rate and flow control as they must be consistent between host and print ...
-
AMT Datasouth 4000 - page 66
User's Guide 65 Paper Paper size Select the label size for your printer. The selected label size may be a little longer than that of the physical label. Orientation Set portrait or landscape according to the print direction. ...
-
AMT Datasouth 4000 - page 67
66 User's Guide Paper source Select one of the following items: T/T & Media with Gap T/T & Media with Black Line T/T & Continuous Media D/T & Media with Gap D/T & Media with Black Line D/T & Continuous Media T/T stands for Thermal Transfer (ribbon) mode and D/T for Direct Thermal model (without ribbon). Media choice Set ...
-
AMT Datasouth 4000 - page 68
User's Guide 67 Device Options Note: The maximum speed varies depending on model: Fm 4402: Max Speed is 4.0 FM 4602/4603: Max Speed is 6.0 ...
-
AMT Datasouth 4000 - page 69
68 User's Guide This is a blank page. ...
-
AMT Datasouth 4000 - page 70
User's Guide 69 TROUBLESHOOTING AND MAINTENANCE Troubleshooting Generally, when a malfunction or an abnormal condition occurs, the “READY” LED will keep blinking. Printing and communication between the host and printer will stop. To understand what the problem is you should first check the LED indicators and LCD display on the front panel: ...
-
AMT Datasouth 4000 - page 71
70 User's Guide Only the Ready LED blinks FM4402 printer Possible Problems Solutions Remarks Serial I/O error Check the baud rate Check the flow control Memory full Add the extension RAM Cutter failed, or jam at cutter Check the cutter Clear the jam Only when cutter is installed. Hardware error Call for service Only the Ready LED blinks FM4602 ...
-
AMT Datasouth 4000 - page 72
User's Guide 71 The data has been sent, but there is no output from the printer • Check the active printer driver, it should be Label Dr. for your Windows system and the label printer. • Check the emulation and the print (command) file. Vertical streaks in the printout usually indicate a dirty or faulty Printhead Clean the printhead first, ...
-
AMT Datasouth 4000 - page 73
72 User's Guide Preventive Maintenance Before performing preventive or any other maintenance be sure to turn off the printer power. Cleaning the Printhead (TPH) 1. Turn off the printer, open the covers, Printhead module and remove the ribbon. 2. Rub the printhead with a piece of cotton, which has been moistened with alcohol. 3. Check for any t ...
-
AMT Datasouth 4000 - page 74
User's Guide 73 Cleaning the Platen roller Using cotton swab moistened with alcohol, clean the roller. Note: The roller should be cleaned whenever it has been in contact with foreign materials such as dust or adhesives. Cleaning the media compartment Clean the media compartment with cotton, which has been moistened with mild detergent. Every t ...
-
AMT Datasouth 4000 - page 75
74 User's Guide This is a blank page. ...
-
AMT Datasouth 4000 - page 76
User's Guide 75 Appendix A: Printer Specifications General Specifications Specification Model FM4402 Model FM4602 Model FM4603 Resolution 203 DPI (8 dots/mm) 203 DPI (8 dots/mm) 300 DPI (12 dots/mm) Print method Direct thermal and thermal transfer Onboard RAM 512K bytes 2M bytes Maximum label roll diameter 8 in. (203 mm) outside diameter 1.5 i ...
-
AMT Datasouth 4000 - page 77
76 User's Guide Fonts, Bar Codes and Graphics The specifications for fonts, bar codes and graphics depend on the printer emulation. The emulation is a printer programming language, through which the host can communicate with your printer. There are two printer programming languages for all models FM4402, FM4602 and FM4603; they are PPLA and PP ...
-
AMT Datasouth 4000 - page 78
User's Guide 77 Optional Accessories ♦ Serial (RS-232) cable ♦ Peel and Present ♦ Cutter ♦ Flash memory (512 K bytes for FM4402 only ) ♦ Font board Notes: The font board and flash modules use the same connector they cannot be installed at the same time. ...
-
AMT Datasouth 4000 - page 79
78 User's Guide This is a blank page. ...
-
AMT Datasouth 4000 - page 80
User's Guide 79 Appendix B: INTERFACE SPECIFICATIONS Introduction This appendix presents the interface specifications of I/O ports for the printer. These specifications include pin assignments, protocols and detailed information about how to properly interface your printer with your host or terminal. Serial The RS-232 connector on the printer ...
-
AMT Datasouth 4000 - page 81
80 User's Guide Connection with host : Host 25S Printer 9P Host 9S Printer 9P (PC or compatible) (PC or compatible) DTR 20 ……….. 1 DSR DTR 4 ……….. 1 DSR DSR 6 ……….. 6 DTR DSR 6 ……….. 6 DTR TX 2 ……….. 2 RX TX 3 ……….. 2 RX RX 3 ……….. 3 TX RX 2 ……….. 3 TX CTS 5 ……….. 7 RTS CTS 8 ……….. 7 ...
-
AMT Datasouth 4000 - page 82
User's Guide 81 Serial port settings Baud rate : 2400, 4800, 9600, 19200 and 38400. To change the Baud Rate: FM4402: Send the <STX>KI8 n command to the printer. See the System Setting Commands section for more details. FM4602/4603: The switches on the back of the printer control Baud Rate. See the Back Panel Switches section for more det ...
-
AMT Datasouth 4000 - page 83
82 User's Guide Parallel (Centronics) The parallel port is a standard 36-pin Centronics. Its pin assignments are listed as following. Pin Direction Definition Pin Direction Definition 1 In /STROBE 13 Out SELECT 2 In Data 1 14,15 NC 3 In Data 2 16 - Ground 4 In Data 3 17 - Ground 5 In Data 4 18 NC 6 In Data 5 19 to 30 - Ground 7 In Data 6 31 NC ...
-
AMT Datasouth 4000 - page 84
User's Guide 83 Appendix C: PRINTER STATUS The printer has built-in monitors for the status. If the printer is equipped with the LCD module the printer status can be displayed on it. The display on LCD is just for models FM4602 and FM4603. LCD display Blinking LED Description PAUSE READY The printer is in a pause state. Press PAUSE or CANCEL t ...
-
AMT Datasouth 4000 - page 85
84 User's Guide Appendix D: ASCII TABLE 0 1 2 3 4 5 6 7 0 NUL 0 @ P ` p 1 SOH XON ! 1 A Q a q 2 STX “ 2 B R b r 3 XOFF # 3 C S c s 4 $ 4 D T d t 5 NAK % 5 E U e u 6 ACK & 6 F V f v 7 BEL ‘ 7 G W g w 8 BS ( 8 H X h x 9 ) 9 I Y i y A LF * : J Z j z B ESC + ; K [ k { C FF , < L l | D CR - = M ] m } E SO RS . > N ^ n ~ F SI US / ? ...
-
AMT Datasouth 4000 - page 86
User's Guide 85 Appendix E: FONTS AND BAR CODES FOR PPLA Internal Fonts Fonts 0 to 8 have single symbol set. ...
-
AMT Datasouth 4000 - page 87
86 User's Guide ...
-
AMT Datasouth 4000 - page 88
User's Guide 87 ...
-
AMT Datasouth 4000 - page 89
88 User's Guide Font 9 Font 9 (ASD smooth font set) includes 8 symbol sets, USASCII, UK, German, French, Italian, Spanish, Swedish, and Danish/Norwegian. The sizes are 4, 6, 8, 10, 12, 14 and 18 points. The 4-point font is for the model FM4603 only. ...
-
AMT Datasouth 4000 - page 90
User's Guide 89 ...
-
AMT Datasouth 4000 - page 91
90 User's Guide Courier Font Set The Courier font set is for the model FM4602 only. It includes Roman-8, PC, PC-A, PC-B, EAMA-94, Legal, Greek and Russian symbol sets. ...
-
AMT Datasouth 4000 - page 92
User's Guide 91 ...
-
AMT Datasouth 4000 - page 93
92 User's Guide ...
-
AMT Datasouth 4000 - page 94
User's Guide 93 ...
-
AMT Datasouth 4000 - page 95
94 User's Guide Internal Bar Codes This PPLA supports 20 one-dimensional bar codes and 2 two dimensional bar codes. ...
-
AMT Datasouth 4000 - page 96
User's Guide 95 ...
-
AMT Datasouth 4000 - page 97
96 User's Guide ...
-
AMT Datasouth 4000 - page 98
User's Guide 97 ...
-
AMT Datasouth 4000 - page 99
98 User's Guide This is a blank page. ...
-
AMT Datasouth 4000 - page 100
User's Guide 99 Appendix F: FONTS AND BAR CODES FOR PPLB Internal Fonts There are 5 internal fonts for the PPLB emulation. Each has 6 eight-bit and 9 seven-bit symbol sets. Font 5 does not contain any lower-case characters. 8 bit symbol sets Code page 437, 850, 852, 860, 863 and 865 7 bit symbol sets USA, British, German, French, Danish, Itali ...
-
AMT Datasouth 4000 - page 101
100 User's Guide ...
-
AMT Datasouth 4000 - page 102
User's Guide 101 ...
-
AMT Datasouth 4000 - page 103
102 User's Guide ...
-
AMT Datasouth 4000 - page 104
User's Guide 103 Internal Bar Codes The PPLB supports 26 one-dimensional bar codes and 2 two dimensional bar codes. ...
-
AMT Datasouth 4000 - page 105
104 User's Guide ...
-
AMT Datasouth 4000 - page 106
User's Guide 105 Appendix F: STAND-ALONE OPERATION FOR KEYBOARD AND BARCODE READER Apart from related hardware devices and PPLB emulation, in order to use keyboards and barcode readers (scanner) you should follow the procedure as described below (FM4602 and FM4603). Note: The Fastmark family ships with PPLA emulation installed. To use the exte ...
-
AMT Datasouth 4000 - page 107
106 User's Guide Example: 1. Make a command file for a form, KBD.FRM. Command Description ZS FK"KBDFORM" FS"KBDFORM" V00,15,N,"Product Name ?" C0,10,N,+1,"Product No. ?" Q50,24 q816 S2 D8 ZT A550,20,0,4,1,1,R,"ABC COMPANY" B550,60,0,2,2,4,40,B,C0 A540,150,0,3,1,1,N,V00 FE ZN Enable the store to ...
-
AMT Datasouth 4000 - page 108
User's Guide 107 4. Press <ESC> to enter the keyboard mode, the form name will be shown for the selection, press <ENTER> key to select the form. KBDFORM ↵ ↵ 5. Key-in product name and number. Product Name ? Barcode Printer ↵ ↵ Product No. ? 0123456789 ↵ ↵ 6. Input the label count and copy count. LABEL SET NO. ? 2 ↵ ? ...
-
AMT Datasouth 4000 - page 109
108 User's Guide Output ...
-
AMT Datasouth 4000 - page 110
User's Guide 109 Barcode Reader 1. Turn off the printer. 2. Make a form for barcode reader; the form name must be “ READER ”. 3. Turn on the printer 4. Download it to the printer and save the form to the flash memory permanently. 5. Turn off the printer 6. Connect the barcode reader to the keyboard I/F. 7. Set bits 6, 7 and 8 of DIP switch ...
-
AMT Datasouth 4000 - page 111
110 User's Guide 2. Send the file, READER.FRM to printer under MS-DOS >COPY/B READER.FRM LPT1: 3. Turn off the printer. 4. Connect the barcode reader to the serial port. 5. Set switches 6, 7 and 8 on the back of the printer to the ON positions. 6. Turn on the printer. 7. The preprogrammed form, READER will start automatically executing. Sca ...
-
AMT Datasouth 4000 - page 112
User's Guide 111 Notes: 1. Set switches 6,7 and 8 to OFF positions and restart the printer to return to normal printer functionality. 2. The bar code reader and keyboard cannot be connected to the PS/2 keyboard I/F simultaneously. 3. When using a keyboard or a barcode reader, the communication with host is only through the Centronics parallel ...
-
AMT Datasouth 4000 - page 113
112 User's Guide This is a blank page. ...
-
AMT Datasouth 4000 - page 114
AMT Datasouth Corp. Corporate Headquarters 4765 Calle Quetzal Camarillo, CA 93012 (805) 388-5799 PH (805) 484-5282 FX Charlotte Operation 4216 Stuart Andrew Blvd. Charlotte, NC 28217 (704) 523-8500 PH (704) 525 6104 FX AMT Datasouth International Unit B, Pinnacle 15 Gowerton Rd, Brackmills Northampton, NN4 7BW England +44 1604 763394 PH +44 1604 76 ...
¿Tienes una pregunta acerca de AMT Datasouth 4000?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con AMT Datasouth 4000, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con AMT Datasouth 4000 probablemente compartirá una forma de solucionarlo.