-
Wybron Optic - page 1
TRANSI TION CMY Fiber Optic Illuminator CMY with TW -White light with WT -White light Transition User Manual ...
-
Wybron Optic - page 2
2 Table of Contents Declaration of Conformity………………………………………………..3 Safety Notice………………………………………………………………4 Introduction to Transition…………………………………………………7 Transition Quick Start configuration………………………………… ...
-
Wybron Optic - page 3
3 ...
-
Wybron Optic - page 4
4 Safety Notice SAVE THESE INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS This manual gives step-by-step instructions for preparation, setup, and operation of the Transition TM Fiber Illuminator. There is a potential risk of fire, electric shock or injury to persons if the product is not used as instructed. The Transition Fiber Illuminator is to be ...
-
Wybron Optic - page 5
5 ...
-
Wybron Optic - page 6
6 Intro to the Transition ...
-
Wybron Optic - page 7
7 Transition Product Introduction Wybron is pleased to announce the introduction of the Transition fiber illuminator. Contained within a small easy to integrate package and ultra bright fiber optic illuminator, the Transition brings quality and durability to your venue. In addition, the Transition is designed to be an integral component of Wybron? ...
-
Wybron Optic - page 8
8 Transition Quick Start Configuration 1. Connect the Equipment a) Connect fiber bundle common end to the Transition output port. b) Connect the Transition to a DMX source with a 5-pin cable c) Connect to AC power (110 – 240 VAC 50/60Hz) 2. Control Transition with DMX Leave Transition addressed at channel 1 (factory default) DMX channel 1 control ...
-
Wybron Optic - page 9
9 Transition Specifications Model 8670: Transition CMY Fiber Illuminator Features: No lamp optimization required Rubber feet for cabinet or countertop installation Durable all metal construction Output supports fiber bundles ranging from 17 – 30 mm dia. High output 150W UHI compact arc source Legendary Wybron Reliability D ...
-
Wybron Optic - page 10
10 Fixture Setup and Configuration Installing the Lamp DANGER: Disconnect fixture from line voltage before replacing lamp. CAUTION: Lamp and lamp mounting surfaces are hot! Allow lamp to cool 10 minutes before replacing Lamp Specifications Lamp socket / base: G22 Part# UHI-S150DW/A/UVP Lamp, Eurospot UHI Series 3000K 150W UHI-S150DM/A/UVP Lamp, Eur ...
-
Wybron Optic - page 11
11 Maximum ambient temperature (t a ) may not exceed 40˚C (104˚F) Keep objects at least 2” (50mm) from sides of the fixture. Keep objects at least 6” from the top of the fixture. Cabinet or Closet Mounting The Transition may be mounted in a closet or cabinet on a hard surface such as wood, laminate, or metal. Do not mount the Transition on so ...
-
Wybron Optic - page 12
12 DMX / RDM Setup and Operation Controls and Indicators Transition controls and indicators as follows: o A three character seven-segment display o 4 push buttons: Menu , ( + ), ( - ), and Enter o Power (red) and signal (green) indicator LED’s The seven-segment display shows the address number (1-508) and the Demo mode (OFF, d1, d2). It also disp ...
-
Wybron Optic - page 13
13 Display Messages Normal Messages 680 Displayed for 1 second after power is applied. This is the RDM manufacturer device identification number Ini Indicates that the unit is initializing the diachronic filters 001 – 508 The first DMX address Transition will respond to. Adr Top menu item. Pressing ‘Enter’ here will allow the current DMX addr ...
-
Wybron Optic - page 14
14 EEP Err An attempt to write to non-volatile memory failed. The unit will continue to respond to commands. SEr Err The RDM unique ID has been corrupted. The unit will operate normally but should not be used in an RDM environment. Contact dealer or factory for assistance. RDM Functionality Transition is compliant with the RDM v1.0 standard and can ...
-
Wybron Optic - page 15
15 Service Lamp Replacement DANGER: Disconnect fixture from line voltage before replacing lamp. WARNING: Lamp and lamp mounting surfaces are hot! Allow lamp to cool before replacing. Disconnect fixture from AC power. Remove lamp plate by removing mounting screws as shown in figure 1.1 and pull lamp assembly straight back from reflector. ...
-
Wybron Optic - page 16
16 Cleaning the Color Filters It is recommended that the color filters be only cleaned with low-pressure air without disassembling the color filters from the motor shafts. If the color module must be disassembled to clean the dichroic filters take careful note of the location and offset height of the individual color flags. Color filters must be re ...
-
Wybron Optic - page 17
17 Flash Reprogramming Transition firmware can be updated as new firmware versions become available through the DMX/RDM port using an Infogate gateway and the Infogate application. Transition firmware updates can be found at www.wybron.com . Specific instructions for upgrading firmware in Transition and other Wybron equipment can be found in the In ...
-
Wybron Optic - page 18
18 Warranty Information WYBRON, INC. warrants to the original owner or retail customer that for a period of one year from date of delivery of a portable system or energization of a permanently installed system (up to a maximum of 18 months from delivery) its products will be free from defects in materials and workmanship under normal use and servic ...
-
Wybron Optic - page 19
19 Figure 2.1 Figure .2 ...
¿Tienes una pregunta acerca de Wybron Optic?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Wybron Optic, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Wybron Optic probablemente compartirá una forma de solucionarlo.