-
Integra DTR-5.8 - page 1
DTR-5.8 Instruction Manual A V Receiver ...
-
Integra DTR-5.8 - page 2
2 Impor tant Safety Instructions 1. Read these instructions. 2. K eep these instructions. 3. Heed all warnings. 4. Foll ow all instructi ons. 5. Do not use this apparatus near water . 6. Clean only with dr y cloth. 7. Do not block any v entilation openings. Install in accordance with the manufact urer’ s instructions. 8. Do not install near any h ...
-
Integra DTR-5.8 - page 3
3 Precautions 1. Recording Copyright —Unless it’ s for personal use only , recording c opyrighted ma terial is ille gal with- out the permission of the copyright holder . 2. A C Fuse —The AC fuse inside the unit is not user- serviceable. If you cannot turn on the unit, contact the dealer from whom you purchased this unit. 3. Care —Occasiona ...
-
Integra DTR-5.8 - page 4
4 Thank you for purchasing an Integra A V Receiv er . Please read this manual thoroughly before making con- nections and plugging in the unit. Follo wing the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your ne w A V Receiver . Please retain thi s manual for future reference. Supplied Access ...
-
Integra DTR-5.8 - page 5
5 T able of Contents Introdu ction Important Safety Instructions ................ .... 2 Precautions ....... .............. ................. ............3 Supplied Accessories .................................. 4 Features ............. .............. ................. ............6 Front & Rear Panels ................... .............. .... 7 ...
-
Integra DTR-5.8 - page 6
6 Features Amplification • 90 watts minimum continuous po wer per channel, 8 ohm loads, 2 channels driv en from 20 Hz to 20 kHz with a maximum total harmonic distortion of 0.08 % (FTC rating) • WRA T -Wi de Range Amplifier T echnology • Optimum Gain V olume Circuitry Proces sing • HDMI and Component V ideo Upcon version •D o l b y *1 Digi ...
-
Integra DTR-5.8 - page 7
7 Fr ont & Rear P anels North American model A ustralian model The page numbers in parentheses show where you can find the main explanation for each item. Standb y/On button (40) This button is used to set the A V receiv er to Standby or On. Standb y indicator (40) This indicator lights up when the A V receiver is in Standby mode, and i ...
-
Integra DTR-5.8 - page 8
8 Front & Rear P anels —Continued (1 T uning Mo de button (57) This button is used to select the Auto or Manual tuning mode. (2 Display b utton (55) This button is used to display v arious information about the currently select ed input source. (3 Setup button This button is used to access the onscreen setup menus that appea r on the conn ect ...
-
Integra DTR-5.8 - page 9
9 Fr ont & Rear P anels —Continued The page numbers in parentheses show where you can find the main explanation for each item. SLEEP indicator (56) This indicator lights up when the Sleep function has been set. MUTING indicator (56) This indicator flashes or lights up while the A V recei ver is muted. HDMI indicator This indicator ...
-
Integra DTR-5.8 - page 10
10 Front & Rear P anels —Continued North American model The page numbers in parentheses show where you can f i nd the main explanation for each item. DIGIT AL OPTICAL IN 1, 2 and OUT These optical digital audio inputs are for connecting components with optical digital audio outputs, such as CD players and D VD players. The optical digital ...
-
Integra DTR-5.8 - page 11
11 Fr ont & Rear P anels —Continued (6 AC I N L E T This connector is for connecting the supplied po wer cord. (7 REMO TE CONTROL This (Remote Int eracti ve) jack can be con- nected to an jack on another -capable Inte- gra component. The A V receiv er’ s remote controller can then be used to control that component. T o use , you must make a ...
-
Integra DTR-5.8 - page 12
12 Remote Contr oller Notes: • If the remote controlle r doesn’t w ork reliably , try replacing the batteries. • Don’t mix ne w and old batteries or differ ent types of batteries. • If you intend not to use the remote controller for a long time, remove the batteries to pre vent damage from leakage or corrosion. • Expired batteries shoul ...
-
Integra DTR-5.8 - page 13
13 Remote Controller —Contin ued The remote controller can be used to control different components including the A V receiver . The remote con- troller has a specific operati ng mode for use with each type of component. Modes are selected b y using the six Remote Mode buttons. ■ Receiver/T ape Mode In Receiv er/T ape mode, you can control the A ...
-
Integra DTR-5.8 - page 14
14 Remote Contr oller —Continued For detailed information, see the pages in parentheses. Zone 2 b utton (86) Used to select the input source for Zone 2. Standby/On b utton (40) Sets the A V recei ver to Standb y or On. Input Selector butt ons (54) Used to select the input sources. Multi CH button (55) Selects the multic hannel D V ...
-
Integra DTR-5.8 - page 15
15 Remote Controller —Contin ued By default, the remote con troller is set to control an Inte- gra D VD player . Standby/On b utton Sets the D VD player to Standby or On. Number butt ons Used to enter title, cha pter , and track numbers and times for locating spe cific po ints. Disc +/– bu tton Selects discs on a D VD changer . ...
-
Integra DTR-5.8 - page 16
16 Remote Contr oller —Continued By default, the remote cont roller is set to control an Inte- gra CD player . Standb y/On button Sets the component to Standby or On. Number buttons Used to ente r track numbers an d times for loca ting specific points on CD/MD players. Disc/Alb um +/– b utton Selects discs on a CD changer, or the ne ...
-
Integra DTR-5.8 - page 17
17 About Home Theater Thanks to the A V receiver’ s superb capabilities, you can enjoy surround sound with a real sense of mov ement in your own home—just lik e being in a movie theater or concert hall. W ith D VDs you can enjoy DTS and Dolby Digital. W ith analog and digital TV you can enjoy Dolby Pro Logic IIx or Onkyo’ s own DSP surround l ...
-
Integra DTR-5.8 - page 18
18 Connecting the A V receiver • Before making any A V connections, read the manu als supplied with your other A V components. • Don’t connect the po wer cord until you’ ve completed and double-checked all A V connections. Optical Dig ital Jac ks The A V receiver’ s optical digital jacks hav e shutter -type cove rs that open when an optic ...
-
Integra DTR-5.8 - page 19
19 Connecting the A V receiver —Continued Speaker Config uration For the best surround sound experience, yo u should con- nect se ven speakers and a po wered subwoofer . The following table indicates the channels you should use depending on the number of speaker s that you hav e. *If you’re using only one surround back speaker, con nect it to t ...
-
Integra DTR-5.8 - page 20
20 Connecting the A V receiver —Continued Speaker Connection Pre cautions Read the following before co nnecting your speakers: • North American models: Only connect speakers with an impedance of 6 ohms or higher . If you use speakers with a lo wer impedance, and use the ampli- fier at high v olume le vels for a long period of time, the built-in ...
-
Integra DTR-5.8 - page 21
21 Connecting the A V receiver —Continued The FR ONT L/R and SURR BA CK L/R terminal posts can be used with front speakers and surro und back speaker s respecti vely , or bi-amped to provid e separate tweeter and woofer feeds for a pair of front speakers that support bi-amping, providin g improved bass and treble performance. • When bi-amping i ...
-
Integra DTR-5.8 - page 22
22 Connecting the A V receiver —Continued This section explains ho w to connect the supplied indoor FM antenna and AM loop antenna, and ho w to connect commercially av ailable outdoor FM and AM antennas. The A V receiver won’ t pick up any radio signals without any antenna connected, so you must co nnect the antenna to use the tuner . Connectin ...
-
Integra DTR-5.8 - page 23
23 Connecting the A V receiver —Continued Connecting an Outdoor FM Antenna If you cannot achie ve good reception with the supplied indoor FM antenna, try a commercially a v ailable out- door FM antenna instead. Notes: • Outdoor FM antennas work best outside, but usable results can sometime s be obtained when installed in an attic or l oft. • ...
-
Integra DTR-5.8 - page 24
24 Connecting the A V receiver —Continued By connecting both the audio and video outputs of your D VD player and other A V components to the A V receiv er, you can select both the audio an d video simultaneously simply b y selecting the appropriate input source on the A V receiv er. The A V receiv er supports several connection formats for compat ...
-
Integra DTR-5.8 - page 25
25 Connecting the A V receiver —Continued ■ HDMI Monitor Setting Set to No W ith the HDMI Monitor setting set to No (see page 47), video input signals f low th rough the A V recei ver as sho wn, with composite video and S-V ideo sources being upcon verted for the com- ponent video output. Use this setting if you con- nect the A V receiver’ s ...
-
Integra DTR-5.8 - page 26
26 Connecting the A V receiver —Continued • W ith connection , you can listen to and record audio from your TV and listen in Zone 2. • T o enjoy Dolby Digital and DTS, use connection or . (For recording, use and , or and .) If your TV has no audio outputs, connect an audio output from your VCR or cable or satellite receiv er to the A V receiv ...
-
Integra DTR-5.8 - page 27
27 Connecting the A V receiver —Continued • W ith connection , you can listen to and record audio from a D VD and listen in Zone 2. • T o enjoy Dolb y Digital and DTS, use connection or . (For recording, use and , or and .) • If your D VD player has main left and right outputs and multichannel left and right outputs, be sure to use the main ...
-
Integra DTR-5.8 - page 28
28 Connecting the A V receiver —Continued Hooking Up the Multichannel D VD Input If your D VD player supports multichannel audio formats such as DVD- Audio or SACD, and it has a multichannel analog audio output, you can connect it to the A V receiv er’ s multichannel D VD input. Use a multichannel analog audio cable, or se veral normal audio ca ...
-
Integra DTR-5.8 - page 29
29 Connecting the A V receiver —Continued W ith this hookup, you can use your VCR’ s tuner to listen to your fa vorite TV programs via the A V receiv er, useful if your TV has no audio outputs. • W ith connection , you can listen to the VCR or D VD recorder even in Zone 2. • T o enjoy Dolby Digital and DTS, use connection or . (T o listen i ...
-
Integra DTR-5.8 - page 30
30 Connecting the A V receiver —Continued Notes: • The A V receiver must be turned on for recording. Recording is not possible while it’ s in Standby mode. • If you want to record directly from your TV or playback VCR to the recording VCR without going through the A V receiv er, connect the TV/VCR’ s audio and video outputs directly to th ...
-
Integra DTR-5.8 - page 31
31 Connecting the A V receiver —Continued W ith this hookup, you can use your satellite or cable receiv er to listen to your fa vorite TV programs via the A V receiv er, useful if your TV has no audio outputs. • W ith connection , you can listen to and record audio from th e video source and listen in Zone 2. • T o enjoy Dolb y Digital and DT ...
-
Integra DTR-5.8 - page 32
32 Connecting the A V receiver —Continued • W ith connection , you can listen to and record audio from the game console or listen in Zone 2. • T o enjoy Dolby Digital and DTS, use connection . (T o record or listen in Zone 2 as well, use and .) Connecting a Game Console Connection A V receiver Signal flow Game console Picture quality COMPONEN ...
-
Integra DTR-5.8 - page 33
33 Connecting the A V receiver —Continued Connecting a Camcor der or Other Device Connection A V receiver Signal flow Camcorder or console A UX Input S Video S-Video output A UX Input Video Composite video output A UX Input Audio L/R Analog audio L/R output A UX Input Digital Digital optical output Step 1: Video Connection Choose ...
-
Integra DTR-5.8 - page 34
34 Connecting the A V receiver —Continued About HDMI Designed to meet the demands of digital TV , HDMI (High Definition Multimedia Interface) is a ne w digital interface standard for connecting TVs, projectors, D VD players, set-top boxes, and other video components. Until no w , sev eral separate video and audio cables hav e been required to con ...
-
Integra DTR-5.8 - page 35
35 Connecting the A V receiver —Continued Making HDMI Connections ■ Video Signals Digital video signals recei ved by the HDMI IN jacks are normally output b y the HDMI OUT for d isplay on your TV . Composite video, S-V ideo, and component video sources can be upcon verted for the HDMI output. See “V ideo Con- nection Form ats” on page 24 fo ...
-
Integra DTR-5.8 - page 36
36 Connecting the A V receiver —Continued ■ CD Player or T urntable (MM) with Built-in Phono Preamp • W ith connection , you can listen to and record audio from the CD player and listen in Zone 2. • T o connect the CD player digitally , use connection or . (For recording, use and , or and .) ■ T urntable (MM) with no Ph ono Preamp Built-i ...
-
Integra DTR-5.8 - page 37
37 Connecting the A V receiver —Continued ■ RI Doc k with video Connect your RI Dock’ s analog audio output jacks and S-V ideo output jack to the A V receiv er’ s GAME/TV IN L/R jacks and GAME/TV IN S jack. (The example sho wn belo w is for connection with the DS-A1.) ■ RI Dock without video Connect your RI Dock’ s analog audio output j ...
-
Integra DTR-5.8 - page 38
38 Connecting the A V receiver —Continued • W ith connection , you can play and record and listen in Zone 2. • T o connect the recorder digitally for playback, use connections and , or and . • T o connect the recorder digitally for recording, use connection . d Connecting a Cassette, CDR, MiniDisc, or D A T Recorder LR OPTICAL IN COAXIAL OU ...
-
Integra DTR-5.8 - page 39
39 Connecting the A V receiver —Continued W ith (Remote Interacti ve), you can use the follo w- ing special functions: ■ Auto P ower On/Standby When you start playback on a component connected via , if the A V receiver is on Standb y , it will auto- matically turn on and select that component as the input source. Similarly , when the A V receiv ...
-
Integra DTR-5.8 - page 40
40 T urning On the A V Receiver • Connect the A V receiver’ s power cord to a suitable wall outlet. Notes: • Befor e connecting the power cord, conn ect all of your speakers and A V components. • T urning on the A V receiv er may cause a momentary power sur ge that might interfere with other electrical equipment on the sa me circuit. If t h ...
-
Integra DTR-5.8 - page 41
41 Fir st Time Setup This section explains the settings that you need to make before using the A V receiver for the very f irst time. W ith the supplied speaker setup microphone, the Audyssey 2EQ function can measure the number of speakers con nected, their size s, crossove r frequencies, and the distance from each spea ker to the listening posi- t ...
-
Integra DTR-5.8 - page 42
42 First Time Setup —Continued 2 Put the speaker setup micro- phone at measurement point (page 41), and connect it to the Setup Mic jack. Notes: • Make sure the microphone is h ori- zontal. • If there’ s an obstacle between the microphone and any speak er , the automatic setup will not work cor- rectly . Set up the room as you would whe ...
-
Integra DTR-5.8 - page 43
43 First Time Setup —Contin ued Notes : • When the automatic speak er setup is complete, the Equalizer Settings (page 72) will be set to “ Audyssey . ” • Y ou can cancel the automatic speak er setup at an y point in this procedure simply b y disconnecting the setup microphone. 6 The f ollowin g screen appe ars. Move the speaker setup micr ...
-
Integra DTR-5.8 - page 44
44 First Time Setup —Continued Error Messa ges While the automatic speaker set up is in progress, one of the follo wing error me ssages may appear: ❏ Ambient noise is too high This message appears if the background noise is too loud and the measurements cannot be performed properly . Remov e the source of the noise and try again. Retry : Return ...
-
Integra DTR-5.8 - page 45
45 First Time Setup —Contin ued Reviewing the Results Changing the Speaker Set tings Manuall y In some situations, the measurement s taken by the auto- matic speak er setup may not p rovide usable results. If running the speaker setup a second time still doesn’ t pro- vide usable results, you’ll ha ve to set the speak er settings manually (se ...
-
Integra DTR-5.8 - page 46
46 First Time Setup —Continued The onscreen setup menus are displayed on the connected TV and provide a con venient way to change the A V receiv er’ s settings. About the Onscreen Setup Menus Menu 1. Input/Output Assign 2. Speaker Setup 3. Audio Adjust 4. Source Setup 5. Listening Mode Preset 6. Miscellaneous 7. Hardware Setup 8. Lock Setup 1. ...
-
Integra DTR-5.8 - page 47
47 First Time Setup —Contin ued If you connect your TV to the COMPONENT VIDEO OUT , set the HDMI Monitor setting to No so that the onscreen setup menus are displayed and composite video and S-V ideo sources are upcon verted* and output by the COMPONEN T VIDEO OUT . If you connect your TV to the HDMI OUT , set the HDMI Monitor setting to Y es so t ...
-
Integra DTR-5.8 - page 48
48 First Time Setup —Continued HDMI Input Setup If you connect a video component to HDMI IN 1 or 2, you must assign that input to an input selector . For exam- ple, if you connect your D VD player to HDMI IN 1, you must assign HDMI IN 1 to the D VD input selector . If you’ ve connected your TV to the A V receiv er with an HDMI cable, you can se ...
-
Integra DTR-5.8 - page 49
49 First Time Setup —Contin ued Component Vid eo Setup If you connect to a COMPONENT VIDEO IN, you must assign it to an input selector . For example, if you connect your D VD player to COMPONENT IN 3, you should assign it to the D VD input selector . If you want to output composite and S-V ideo sources from the COMPONENT VIDEO OUT , select “--- ...
-
Integra DTR-5.8 - page 50
50 First Time Setup —Continued If you connect a component to a digital input jack, you must assign that jack to an input selector . For example, if you connect your CD player to the OPTICAL IN2 jack, you should assign that jack to the CD input selector . By default, the CO AXIAL IN1 jack is assigned to the DVD input selector , although this can b ...
-
Integra DTR-5.8 - page 51
51 First Time Setup —Contin ued If you connect an -capable Inte gra MiniDisc recorder , CD recorder , or RI Dock t o the T APE IN/OUT or GAME/TV IN jacks, for to wor k properly , you must change this setting. This setting can only be changed on the A V receiv er. iPod photo: If you’ re using an iPod photo with the DS-A1 Remote Interacti ve Dock ...
-
Integra DTR-5.8 - page 52
52 First Time Setup —Continued Note: This procedure can also be performed on the A V receiv er by using its [Setup] b utton, arro w buttons, and [Enter] button. Y ou must specify the TV system used in your area. Note: This procedure can also be performed on t he A V receiver by using its [Setup] button, arro w buttons, and [Enter] button. 4 Use t ...
-
Integra DTR-5.8 - page 53
53 First Time Setup —Contin ued Y ou must specify the AM frequency step used in your area. Note that when this se tting is changed, all radio presets are deleted. Note: • This procedure can also be performed on the A V recei ver b y using its [Setup] button, arro w button s, and [Enter] b utton. AM Frequency Step Setup (A ustralian model) 1 Pre ...
-
Integra DTR-5.8 - page 54
54 Basic Operations This section explains ho w to select the input source (i.e., the A V compone nt that you want to listen to or watch). Selecting the Input Sour ce 1 3 Multi CH 3 1 1 Multi CH 1 Use the A V receiv er’ s input selector buttons to select the input sour ce. T o select the input source with the remote controller , press the [Receive ...
-
Integra DTR-5.8 - page 55
55 Basic Operations —Continued The multichannel D VD input is for connecting a compo- nent with a 7.1-channel analo g audio output, such as a D VD- Audio or SA CD-capable D V D player , or an MPEG decoder . See page 28 for hookup information. Note: While the multichanne l D VD input is selected, the Speaker Conf iguration settings on page 68 are ...
-
Integra DTR-5.8 - page 56
56 Basic Operations —Contin ued Y ou can adjust the brightness of the display . Y ou can temporarily mute the output of the A V recei ver. W ith the sleep timer , you can set the A V receiv er to turn off automatically after a specif ied period. If you need to cancel the sleep timer , press the [Sleep] button repeatedly unt il the SLEEP indicator ...
-
Integra DTR-5.8 - page 57
57 Listening to the Radio W ith the built-in tuner you can enjoy AM and FM radio stations. Y ou can store your fav orite stations as presets for quick selectio n. Listening to the Radio T uning into Radio Stations ■ A uto T uning Mode When tuned into a station, the TUNED indi cator appears. When tuned into a stereo FM station, the FM STEREO indic ...
-
Integra DTR-5.8 - page 58
58 Listening to the Radio —Continued Y ou can store a combination of up to 40 of your fa vorite AM/FM radio stations as presets. Selecting Presets Deleting Presets Presetting AM/FM Stations 1 T une into the AM/FM station that y ou want to store as a preset. 2 Press the [Memory] button. The preset number flashes. 3 While the preset number is flash ...
-
Integra DTR-5.8 - page 59
59 Using the Listening Modes See “ About the Listening Modes” on page 64 for detailed information about the listening modes. Selecting on th e A V receiver ■ [Stereo] button This button selects the Stereo listening mode. ■ Listening Mode [ ]/[ ] buttons Pressing these buttons repeatedly c ycles through all of the listening modes that can be ...
-
Integra DTR-5.8 - page 60
60 Using the Listening Modes —Continued Analog and PCM Sour ces *1. For PCM 176.4/192 kHz signals input thro ugh HDMI IN, only, Direct and Stereo listening modes can b e selected. (HDMI input on ly) *2. If there are no surround back sp eakers, or Powered Zone 2 is being used, Dolby Pro Logi c II is used. *3. PCM 32-48 kHz s ignals only. *4. Avail ...
-
Integra DTR-5.8 - page 61
61 Using the Listening Modes —Continued Dolb y Digital, Dolby Digital Plus, and T rueHD Sources *1. During input o f a 96 kHz TrueHD signal, th e only sound balance or so und quality adjustm ent that can be made is T one control. The AV receiver does not respond to a 192 kHz TrueHD signal. *2. If there are no surround back speakers, dependi ng on ...
-
Integra DTR-5.8 - page 62
62 Using the Listening Modes —Continued DTS and DTS 96/24 Sour ces *1. If there are no surround back sp eakers, or Powered Zone 2 is being used, DTS is used. *2. If there are no surround back sp eakers, or Powered Zone 2 is being used, Dolby Pro Logi c II is used. *3. Available on ly when using s urround speakers. *4. For T-D, Mono Mo vie, Orches ...
-
Integra DTR-5.8 - page 63
63 Using the Listening Modes —Continued DTS-HD High Resolution A udio and DTS-HD Master Audio Sour ces *1. During input of a 96 kHz DTS-HD Master Audio signal, the only sound b alance or sound quality adjust ment that can be made is Tone control. When input is a 192 kHz DTS-HD Master Audio signal, i t should be played at 96 kHz. *2. If there are ...
-
Integra DTR-5.8 - page 64
64 Using the Listening Modes —Continued The A V receiver’ s listening modes can transform your listening room into a movie theater or concert hall, with high fidelity and stunning surround sound. Direct In this mode, audio from the input source is output directly with minimal processing, providing high-fidel- ity reproduction. All of the source ...
-
Integra DTR-5.8 - page 65
65 Using the Listening Modes —Continued DTS-ES Matrix This mode is for use with DTS-ES Matrix soundtracks, which use a matrix-encoded back-channel for 6.1/7.1- channel playback. Use it with D VDs that bear the DTS- ES logo, especially those with a DTS-ES Matrix soundtrack. DTS Neo:6 This mode expands an y 2-channel source for 7.1-chan- nel playba ...
-
Integra DTR-5.8 - page 66
66 Recor ding This section explains ho w to record the selected input source to a component with recording capability , and how to r ecord audio and video from dif ferent sources. Notes: • The surround sound and DSP listening modes cannot be recorded. • Copy-protected D VDs cannot be recorded. • Y ou cannot record from the D VD analog multich ...
-
Integra DTR-5.8 - page 67
67 Ad v anced Operations W ith the Late Night function, you can reduce the dynamic range of Dolby Digital, Dolby Digital Plus, and Dolby T rueHD material so that you can still hear quiet parts e ven when list ening at lo w volume le vels—ideal for watching movies late at night when you don’ t want to disturb anyone. Notes: • Depending on the ...
-
Integra DTR-5.8 - page 68
68 Adv anced Setup Some of the setti ngs in this section are set automatical ly by the Au tomatic Speaker Setup function (see page 41). Here you can check the settings made by the Automatic Speaker Setup function, or set them manually , which is useful if you change one of the co nnected speakers after using the Automatic Speaker Setup function. Sp ...
-
Integra DTR-5.8 - page 69
69 Adv anced Setup —Continued Low-P ass Filter for the LFE Channel W ith this setting, you can specify the cutoff frequenc y of the LFE channel’ s low-pass f ilter (LPF), which can be used to filter out unw anted hum. The LPF only applies to sources that use the LFE channel. Double Bass W ith the Double Bass function, you can boost bass out- pu ...
-
Integra DTR-5.8 - page 70
70 Adv anced Setup —Continued Speaker Distance Here you can specify the d istance from each speaker to the listening position so th at the sound from each speaker arri ves at the listener’ s ears as the sound designer intended. Notes: • The Center and Subwoofer distances can be set up to 5 ft. (1.5 m) more or less than the Front distance. For ...
-
Integra DTR-5.8 - page 71
71 Adv anced Setup —Continued Speaker Level Calibration Here you can adjust the lev el of each speaker with the built-in test tone so that the v olume of each speaker is the same at the listening position. Note: The speakers cannot be calibrated while the output of the A V receiv er is muted or while a pair of headphones is connected. Notes: • ...
-
Integra DTR-5.8 - page 72
72 Adv anced Setup —Continued Equalizer Setting Here you can adjust the EQ of indi vidual speakers. T o set the volume of indi vidual speakers see page 71. 1 Press the [Receiver] button fol- lowed by the [Setup] button. The main menu a ppears onscreen. 2 Use the Up and Down [ ]/[ ] buttons to select “2. Speaker Setup, ” and then press [Enter] ...
-
Integra DTR-5.8 - page 73
73 Adv anced Setup —Continued Notes: • When the listeni ng mode is set to Direct, no e ffect wil l be produced. • Depending on the input source or listening mode, the Equalizer settings may not produce the desired effect. • This procedure can also be performed on the A V recei ver b y using its [Setup] button, arro w button s, and [Enter] b ...
-
Integra DTR-5.8 - page 74
74 Adv anced Setup —Continued Here you can set listening mode-related settings and functions. Note: This procedure can also be performed on the A V receiv er by using its [Setup] b utton, arro w buttons, and [Enter] button. The Audio Adjust functions are e xplained below . T one Contr ol Settings Y ou can adjust the bass and trebl e for the front ...
-
Integra DTR-5.8 - page 75
75 Adv anced Setup —Continued PL II x/Neo:6 Mu sic Mode Settings These settings provide for playing an y 2-channel digital source such as Dolby Digital, or 2-channel analog/PCM source in the Dolby PLIIx Music listening mode. ■ Panorama W ith this function, you can broaden the width of the front stereo image when using the Dolby Pro Logic II Mus ...
-
Integra DTR-5.8 - page 76
76 Adv anced Setup —Continued Y ou can assign a default listening mode to each input source that will be selected automatically when you select each input source. For example, you can set the default listening mode to be used with Dolby Digital input signals. Y ou can select other listening modes dur- ing playback, but the mode specif ied here wi ...
-
Integra DTR-5.8 - page 77
77 Adv anced Setup —Continued Note: This procedure can also be performed on the A V receiv er by using its [ Setup] button, arro w buttons, and [Enter] butto n. IntelliV olume Y ou can set the input lev el for each input source. This is useful if some of your A V components are louder or qui- eter than others. IntelliV olume does not af fect Zone ...
-
Integra DTR-5.8 - page 78
78 Adv anced Setup —Continued Correcting Sound and Picture Sync When using progressiv e scanning on your DVD player , you may find that the picture and sound are out of sync. W ith this setting, you can correct this by delaying the audio signals. Y ou can set it from 0 to 100 milliseconds (msec) in 2 millise cond steps. Note: • This setting is ...
-
Integra DTR-5.8 - page 79
79 Adv anced Setup —Continued This section explains the items on the Miscellaneous menu. Vo l u m e S e t u p Note: This procedure can also be performed on the A V receive r by using its [Setup] button, arr ow b uttons, and [Enter] button. V olume Setup/OSD Setup 1 Press the [Receive r] button f ol- lowed b y the [Setup] button. The main menu app ...
-
Integra DTR-5.8 - page 80
80 Adv anced Setup —Continued OSD Setup Note: This procedure can also be performed on t he A V receiver by using its [Setup] button, arro w buttons, and [Enter] button. 1 Press the [Receiver] button fol- lowed by the [Setup] button. The main menu a ppears onscreen. 2 Use the Up and Down [ ]/[ ] buttons to select “6. Miscellaneous, ” and then ...
-
Integra DTR-5.8 - page 81
81 Adv anced Setup —Continued . Note: This procedure can also be performed on the A V receiv er by using its [ Setup] button, arro w buttons, and [Enter] butto n. Changing the A V receiver’ s ID 1 Press the [Receive r] button f ol- lowed b y the [Setup] button. The main menu appears onscreen. 2 Use the Up and Down [ ]/[ ] buttons to select “7 ...
-
Integra DTR-5.8 - page 82
82 Adv anced Setup —Continued HDMI A udio Out This preference determines whet her audio receiv ed at the HDMI IN is output by the HDMI OUT . Y ou may want to turn this preference on if your TV is connected to the HDMI OUT and you want to listen to the aud io from a component that’ s connected to an HDMI IN, through your TV’ s speakers. Normal ...
-
Integra DTR-5.8 - page 83
83 Adv anced Setup —Continued The digital input signal formats are av ailable only for the input sources that you ha ve assigned a digita l input jack; otherwise you will see “ Analog” indicated on the screen (see page 50). Normally , the A V receiv er de tects the signal format auto- matically . Howe ver , if you experience either of the fol ...
-
Integra DTR-5.8 - page 84
84 Zone 2 W ith the Zone 2 function, you can enjoy one input source in the main room and a dif ferent source in another room. There ar e two ways to hook up y our Zone 2 speakers: 1) Use another amp (recei ver , integrated amp, or power amp) in Zone 2 and connect your Zone 2 speakers to it. 2) Connect your Zone 2 speakers to this A V receiv er. Not ...
-
Integra DTR-5.8 - page 85
85 Zone 2 —Continued Note: This procedure can also be performed on the A V receiv er by using its [ Setup] button, arro w buttons, and [Enter] butto n. If you’ ve connected your Zone 2 speakers to a po wer amp with no volume control in Zone 2, as e xplained in “Using Another Amp in Zone 2” on page 84, you must set the Zone 2 Out setting to ...
-
Integra DTR-5.8 - page 86
86 Zone 2 —Continued Note: This procedure can also be performed on the A V receiv er by using its [Setup] b utton, arro w buttons, and [Enter] button. This section explains ho w to turn Zone 2 on and of f, ho w to select an input source for Zone 2, and how to adjust the vo lume for Zone 2. Controlling Zone 2 fr om the A V receiver Contr olling Zo ...
-
Integra DTR-5.8 - page 87
87 Zone 2 —Continued Adjusting the V olume for Zone 2 To M u t e Z o n e 2 : Press the remote controller’ s [Zone 2] button, follo wed by the [Muting] button. T o unmute Zone 2, press the remote controller’ s [Zone 2] button again, follo wed by the [Muting] button, or adjust the volu me for Zone 2. Notes: • Only analog input sources are out ...
-
Integra DTR-5.8 - page 88
88 Zone 2 —Continued When the A V recei ver’ s 12 V TRIGGER OUT A /B/C jack is connected to the 12 V trigger input on a connected component, you can specify whether or not a 12-volt trigger signal is output when that component is selected as the source for the main room, Zone 2, or either . Hookup • Use a miniplug cable to connect the A V rec ...
-
Integra DTR-5.8 - page 89
89 Zone 2 —Continued T o control the A V receiv er with the remote controller while you’ re in the Zone 2 room, you’ll need a commer- cially a v ailable multir oom remote control k it. • Multiroom kits are made by Niles and Xantech. These kits can also be used w hen there isn’t a clear line of sight to the A V recei ver’ s remote sensor ...
-
Integra DTR-5.8 - page 90
90 Contr olling Other Components Y ou can use the A V recei v er’ s remote controller (RC-683M) to control your other A V components, including those made by ot her manufacturers. This sec- tion explains ho w to enter the nece ssary remote control code for the component that you want to control (e.g., D VD player , TV , or VCR). T o control anoth ...
-
Integra DTR-5.8 - page 91
91 Contr olling Other Components —Continued Integra components that are connected via are con- trolled by pointing the remote controller at the A V receiv er, not the component. This allows you to control components that are out of vie w , in a rack, for example. If you want to control an Integra component b y pointing the remote controller direc ...
-
Integra DTR-5.8 - page 92
92 Controlling Other Components —Contin ued T o control another component, point the r emote contr oller at it and use the b uttons explained below . (Y ou must select the appropriate remote co ntrol mode f irst.) With some A V components, certain b uttons may not work as expected, and some may not work at all. ■ Contr olling a TV [Standby/ ...
-
Integra DTR-5.8 - page 93
93 Specifications Amplifier Section Video Section T uner Section General ■ Video Inputs ■ Video Outputs ■ A udio Inputs ■ A udio Outputs ■ Control T erminals Specifications and features are subject to change without notice. Rated Output Power (FTC) All channels: 90 watts mini mum continuous po wer per channel , 8 ohm loads , 2 channels dr ...
-
Integra DTR-5.8 - page 94
94 T r oubleshooting If you hav e any trouble using the A V receiv er, look for a solution in this section. If you can’ t resolve the issue yourself, contact the dealer from whom you purchased. Can’t turn on th e A V rec eiver • Make sure that the po wer cord is properly plugged into the wall outle t. • Unplug the power cord from the wall o ...
-
Integra DTR-5.8 - page 95
95 T roubleshooting —Contin ued The surround bac k speakers produce no sound • The surround back speakers are not used with all listen- ing modes. Select another li stening mode (page 64). • Not much sound may be produced by the surround back speakers with some sources. • Make sure the speakers are configu red correctly (page 68). The subwo ...
-
Integra DTR-5.8 - page 96
96 T roubleshooting —Continued • If the video source is connected to a componen t video input, your TV must be connected to the COMPO- NENT VIDEO OUT or HDMI OUT (page 25). • If the video source is connected to an HDMI input, your TV must be connected to the HDMI OUT (page 25). • On your TV , make sure that the video input to which the A V ...
-
Integra DTR-5.8 - page 97
97 T roubleshooting —Contin ued Can’t record • On your recorder , make sure the correct input is selected (e.g., digital or analog). There’ s no sound • Only components connected to analog inputs can be played in Zone 2. The sound changes when I connect my head- phones • When a pair of headphones is connected, the listening mode is set ...
-
Integra DTR-5.8 - page 98
98 MEMO ...
-
Integra DTR-5.8 - page 99
99 MEMO ...
-
Integra DTR-5.8 - page 100
100 SN 29344500 (C) Copyright 2007 ONKY O CORPORA TION Japan. All r ights reser ved. Y0704-1 Integra Division of ONKYO U.S.A. CORPORATION 18 park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: 201-785-2600 Fax: 201-785-2650 http://www.integrahometheater.com Integra Division of ONKYO CORPORATION Sales & Product Planning Div.: 2-1, Nisshin-cho, ...
¿Tienes una pregunta acerca de Integra DTR-5.8?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Integra DTR-5.8, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Integra DTR-5.8 probablemente compartirá una forma de solucionarlo.