-
Philips PXG10 - page 1
Philips Creativ e Displa y Solutions User guide P ro S cr een PXG10 m ultimedia pr ojector ) ) A/V Mute A/V Mute Auto sync Auto sync Input Input OK OK Lens Lens D-Zoom D-Zoom Menu Menu ...
-
Philips PXG10 - page 2
IMPORT ANT NOTE FOR USERS IN THE U.S.A. The responsible party of this multi media projector is the following: Philips Consumer Electronics Company One Philips Drive Knoxville, TN 37914 T elephone (1888) 873-4672 W ARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. This “bolt of lightning” indic ...
-
Philips PXG10 - page 3
1. IMPOR T ANT SAFEGUARDS 1. Unplug the projector from the wall outlet before cleaning or lamp replacement. 2. Do not use liquid cleaners or aerosol cleaners. Use a soft dry cloth to clean the projector unit. If the unit is very dirty , wet a cloth with neutral detergent, squeeze it tight, wipe the unit with it, and finish by wiping with a dry clot ...
-
Philips PXG10 - page 4
T ABLE OF CONTENTS 1. IMPORT ANT SAFEGUARDS .............................................1 2. INTRODUCTION .................................................................2 3. THINGS YOU SHOULD KNOW ........................................3 4. PROJECTOR FEA TURES ....................................................5 5. FUNCTIONAL OVERVIEW ........ ...
-
Philips PXG10 - page 5
3. THINGS YOU SHOULD KNOW Note: This equipment has been tested to comply with the limits for a class A digital device in accordance with Part 15 of the FCC Rules as well as the European CE marking. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference ...
-
Philips PXG10 - page 6
4 English ) ) ( ) ¡ ™ ≤ £ ™ Data 1 in (15pin) 15pin BNC R (Pr) L R APP ARA TEN SKALL ANSLUT AS TILL JODA T UTT AG. B (Pb) VD G/G sync (Y) HD (C sync) Data 1 in (BNC) Data 2 in Audio 1 Audio 2 Data 1 in (15pin) 15pin BNC R (Pr) L R APP ARA TEN SKALL ANSLUT AS TILL JODA T UTT AG. B (Pb) VD G/G sync (Y) HD (C sync) Data 1 in (BNC) Data 2 in Au ...
-
Philips PXG10 - page 7
4. PROJECTOR FEA TURES 1. ADV ANCED COMP A TIBILITY WITH HIGH-END WORKST A TIONS AND PCS Compatible with up to 130 Hz vertical refresh rate, Sync on Green and Composite Sync signals for use with a wide variety of high-end PCs and Workstations. (Page 11) 2. FOR USE WITH DTV* Allows projection of DTV images and 16:9 wide-screen images when connected ...
-
Philips PXG10 - page 8
CONTROLS On project or (fig. 1) 1 P ower ON z F or switc hing the projector in power on. Standby/OFF y F or switc hing the projector in st andby mode. 2 Lens F or selecting the optical lens adjustments Zoom and Focus and the electronic Ke ystone correction. T he but ton toggles between the Zoom-, F ocus- and Key stone function. 3 Data-1 but ton F o ...
-
Philips PXG10 - page 9
5. FUNCTIONAL OVER VIEW See illustrations on page 4 On remote control (fig. 2) 1 On / Off switch z / y For switching the remote control as well as the projector on and off. Note: The remote control will always use some power , even when not in use. The remote control unit will automatically switch off when not used for 30 minutes. 2 T racking Ball ...
-
Philips PXG10 - page 10
POSITIONING THE PROJECTOR AND SCREEN Position the projector perpendicular to the screen with all feet flat and level to achieve an optimal image. Move the projector forward or backward if the edges of the image are distorted. • The projector lens should be centred in the middle of the screen. If the lens centre is not perpendicular to the screen, ...
-
Philips PXG10 - page 11
6. SET UP LENS ADJUS TMENT Focus, Zoom and electronic K eystone 1. Press L ens to select mode. – Eac h time Lens is pressed, the screen c hanges in the follo wing order . 2. Press OK to displa y test pat tern. 3. Press 1 , 2 , 3 or 4 to make adjustments. 4. Press L ens until normal screen appears. Note: – The On Screen Displa ys will automatica ...
-
Philips PXG10 - page 12
VIDEO/COMPUTER CABLES AND ADAPTER These accessories are supplied for connecting the projector to computer/Audiovisual equipment. The numbers in the left-hand column correspond with the numbers in the connection diagrams on the following pages. Optional cables and adapter: – Computer cable Mini D sub (15 pin) BNC connectors (5x) – Programmable V ...
-
Philips PXG10 - page 13
7 . INS T ALLA TION Connecting to a comput er CONNECTING T O A COMPUTER General – The data input (Dat a 1 and 2) is suitable for both Apple Macintosh computers (P ow er Book and P ow er Mac) as well as for IBM compatible PCs. – The data output of IBM compatible PCs can be connected directly to the projector using st andard computer V GA cable. ...
-
Philips PXG10 - page 14
V CR, Laser disc, other audiovisual equipment using standard video input 1. Connect the yello w RCA connector (K) to the corresponding yello w Video Input terminal on the projector and the Video output terminal on the video source. 2. T o use the built-in audio system, connect the red and white RCA connectors to the cor responding red and white Aud ...
-
Philips PXG10 - page 15
7 . INS T ALLA TION Connecting to audio equipment/r emote contr ol mouse receiv er CONNECTING T O AUDIO EQUIPMENT CA UTION! Alwa ys t urn off the projector while connecting to audio components, in order to protect both the projector and the components being connected. By using external audio components, the volume can be amplified f or bet ter soun ...
-
Philips PXG10 - page 16
PREP ARA TION T urning on/of f the power 1. Make the necessary connections before proceeding. Connect the pow er cord to a wall outlet. The P ow er indicator lights up red and the projector enters standby mode. 2. Press P ow er ON. The po wer indicator lights up green and the flashing green Lamp indicator shows that the lamp is w arming up. Wait un ...
-
Philips PXG10 - page 17
8. OPERA TION Graphical User Interface DA T A MODE MENU CONTROL 1. Press Menu to display the Data mode menu bar . 2. Press 1 / 2 to select an adjustment menu on the menu bar . 3. Press 3 / 4 to select a specific adjustment item. 4. T o display a single adjustment item, press OK after selecting the item. Only the menu bar and the selected adjustment ...
-
Philips PXG10 - page 18
DA T A MODE INPUT SIGNAL Data mode input selection Ordinarily , the type of input signal is detected and the correct resolution mode is automatically selected. However , for some signals, “Special Modes” on the “Fine Sync” menu screen may need to be changed to match the computer display mode. 1. Press Menu. 2. Press 1 / 2 to select “Fine ...
-
Philips PXG10 - page 19
8. OPERA TION Pictur e control D A T A MODE DISPLA Y Data displa y Fine Sync adjustments When displaying computer pat terns whic h are ver y detailed (tiling, vertical stripes, etc.), interf erence may occur between the LCD pixels, causing flic kering, vertical stripes, or contrast irregularities in portions of the screen. Should this occur , adjus ...
-
Philips PXG10 - page 20
D A T A / VIDEO MODE DISPLA Y Pictur e display adjustments F or video signal input, the following adjustments can be made: – Contrast - adjusts the o verall contrast intensit y; – Br ight - adjusts the picture brightness; – Color - adjusts the colour saturation of the projected image; – Tint - for more purplish/greenish skin tones (NTSC onl ...
-
Philips PXG10 - page 21
8. OPERA TION P ersonal pr ef erences/Other set tings 3. Press 3 / 4 to select “ Sa ve Set ting ” , and then press OK. 4. Press 3 / 4 to select the desired memor y location of the set ting. 5. Press OK to sa ve the set ting. 6. T o exit from the GUI, press Menu. Selecting a sav ed setting 1. Press Menu. 2. Press 1 / 2 to select “ Fine Sync ? ...
-
Philips PXG10 - page 22
Projection using a mirror – Place a mirror (normal flat type) in front of the lens. – The image reflected from the mirror is projected onto the screen. – Optimal image quality is produced with the projector positioned perpendicular to the screen with all feet flat and level. CAUTION! When using a mirror , be sure to carefully position both th ...
-
Philips PXG10 - page 23
8. OPERA TION Other set tings 21 English Pictur e display mode This function allo ws you to modify or customise the pict ure display mode to enhance the input image. Depending on the input signal, you can c hoose NORMAL, WIDE, DO T B Y DO T , DO T B Y DO T (WIDE), or FIT T O SCREEN image. – Eac h time V -FORMA T is pressed, the picture mode c han ...
-
Philips PXG10 - page 24
A V Mute Function This function can be used f or muting the sound of the projector (or an external connected sound amplifier) and f or muting the picture. Press A/V Mute. –“ AV M u t e ” is display ed on the screen. T o return to the original projected image, press A/V Mute again. T urning of f the On-Screen Displa y (OSD) The On-screen Displ ...
-
Philips PXG10 - page 25
8. OPERA TION Other set tings A utomatic P ow er Shutof f Function When no input signal is detected for more than 1 5 minutes, the projector will automatically shut of f . The on-screen message on the lef t will appear five minutes bef ore the power is automatically turned of f . Inter laced (I)/Progr essive (P) conv ersion This function allo ws yo ...
-
Philips PXG10 - page 26
Setting a Background Image This function allows you to select the image displayed when no signal is being sent to the projector . Description of Background Images Selected item Background image Philips PHILIPS default image Blue Blue screen None Black screen 1. Press Menu. 2. Press 1 / 2 to select “Options”. 3. Press 3 / 4 to select “Backgrou ...
-
Philips PXG10 - page 27
9. ADDITIONAL INFORMA TION Connecting RS-232C port/Maintenance CONNECTING RS-232C PORT When the RS-232C port on the projector is connected to a computer with an RS-232C cable (cross type, sold separately), the computer can be used to control the projector and check the status of the projector . 1. Connect the supplied DIN-D-sub RS-232C cable to the ...
-
Philips PXG10 - page 28
Notes: – If the T emperature w arning indicator lights up, follow the abov e possible solutions and then wait until the projector has cooled down completely bef ore turning the po wer bac k on. (At least 5 minutes.) – If the pow er is turned of f and then turned on again, as during a brief rest, the Lamp indicator may be triggered, pre venting ...
-
Philips PXG10 - page 29
9. ADDITIONAL INFORMA TION Maintenance CA UTION! – T o av oid injur y to yourself and damage to the lamp, be sure to carefully follo w the steps below . – Bef ore or af ter replacing the lamp, be sure to clean the air filters. See page 25 for cleaning the air filters. Resetting the lamp timer 1. Connect the pow er cord. – Plug the pow er cord ...
-
Philips PXG10 - page 30
PROBLEM • CHECK NO PICTURE AND NO SOUND. • Projector po wer cord is not plugged into the wall outlet. • The bot tom filter cover is not securely installed. • Selected input is wrong. (See pages 1 4) • Cables improperly connected to rear panel of the projector . (See pages 1 1 -1 3) • Remote control bat teries have r un down. (See page 9 ...
¿Tienes una pregunta acerca de Philips PXG10?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Philips PXG10, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Philips PXG10 probablemente compartirá una forma de solucionarlo.