-
Analog Devices ADSP-2183 - page 1
FUNCTIONAL BLOCK DIAGRAM a DSP Microcomputers ADSP-2181/ADSP-2183 FEATURES PERFORMANCE 30 ns Instruction Cycle Time @ 5.0 Volts 33 MIPS Sustained Performance 34.7 ns Instruction Cycle Time @ 3.3 Volts Single-Cycle Instruction Execution Single-Cycle Context Switch 3-Bus Architecture Allows Dual Operand Fetches in Every Instruction Cycle Multifunctio ...
-
Analog Devices ADSP-2183 - page 2
ADSP-2181/ADSP-2183 REV. 0 –2– This takes place while the processor continues to: • receive and transmit data through the two serial ports • receive and/or transmit data through the internal DMA port • receive and/or transmit data through the byte DMA port • decrement timer Development System Th e ADSP-2100 Family Development Software, ...
-
Analog Devices ADSP-2183 - page 3
ADSP-2181/ADSP-2183 REV. 0 –3– Program memory can store both instructions and data, permit- ting the ADSP-2181/ADSP-2183 to fetch two operands in a single cyc le, one from program memory and one from data memory. The ADSP-2181/ADSP-2183 can fetch an operand from program memory and the next instruction in the same cycle. In addition to the addre ...
-
Analog Devices ADSP-2183 - page 4
ADSP-2181/ADSP-2183 REV. 0 –4– • SPORTs support serial data word lengths from 3 to 16 bits and provide optional A-law and µ -law companding according to CCITT recommendation G.711. • SPORT receive and transmit sections can generate unique in- terrupts on completing a data word transfer. • SPORTs can receive and transmit an entire circula ...
-
Analog Devices ADSP-2183 - page 5
ADSP-2181/ADSP-2183 REV. 0 –5– Table I. Interrupt Priority & Interrupt Vector Addresses Interrupt Vector Source of Interrupt Address (Hex) Reset (or Power-Up with PUCR = 1) 0000 ( Highest Priority ) Power Down (Nonmaskable) 002C IRQ2 0004 IRQL1 0008 IRQL0 000C SPORT0 Transmit 0010 SPORT0 Receive 0014 IRQE 0018 BDMA Interrupt 001C SPORT1 Tra ...
-
Analog Devices ADSP-2183 - page 6
ADSP-2181/ADSP-2183 REV. 0 –6– When the IDLE (n) instruction is used, it effectively slows down the processor’s internal clock and thus its response time to in- coming interrupts. The one-cycle response time of the standard idle state is increased by n , the clock divisor. When an enabled interrupt is received, the ADSP-2181/ADSP-2183 will re ...
-
Analog Devices ADSP-2183 - page 7
ADSP-2181/ADSP-2183 REV. 0 –7– Table II. PMOVLAY Memory A13 A12:0 0 Internal Not Applicable Not Applicable 1 External 0 13 LSBs of Ad dress Overlay 1 Between 0x2000 and 0x3FFF 2 External 1 13 LSBs of Address Overlay 2 Between 0x2000 and 0x3FFF This organization provides for two external 8K overlay segments using only the normal 14 address bits. ...
-
Analog Devices ADSP-2183 - page 8
ADSP-2181/ADSP-2183 REV. 0 –8– The CMS pin functions like the other memory select signals with the same timing and bus request logic. A 1 in the enable bit causes the assertion of the CMS signal at the same time as the selected memory select signal. All enable bits default to 1 at reset, except the BMS bit. Byte Memory The byte memory space is ...
-
Analog Devices ADSP-2183 - page 9
ADSP-2181/ADSP-2183 REV. 0 –9– Table VI. Boot Summary Table MMAP BMODE Booting Method 0 0 BDMA feature is used in default mode to load the first 32 program memory words from the byte memory space. Program execution is held off until all 32 words have been loaded. 0 1 IDMA feature is used to load any inter- nal memory as desired. Program execu- ...
-
Analog Devices ADSP-2183 - page 10
ADSP-2181/ADSP-2183 REV. 0 –10– If the ADSP-2181/ADSP-2183 is performing an external memory access when the external device asserts the BR signal, then it will not three-state the memory interfaces or assert the BG signal until the processor cycle after the access completes. The instruction does not need to be completed when the bus is granted. ...
-
Analog Devices ADSP-2183 - page 11
ADSP-2181/ADSP-2183 REV. 0 –11– These ADSP-2181/ADSP-2183 pins must be connected only to the EZ-ICE connector in the target system. These pins have no function except during emulation, and do not require pull-up or pull-down resistors. The traces for these signals between the ADSP-2181/ADSP-2183 and the connector must be kept as short as possib ...
-
Analog Devices ADSP-2183 - page 12
ADSP-2181–SPECIFICA TIONS RECOMMENDED OPERA TING CONDITIONS K Grade B Grade Parameter Min Max Min Max Unit V DD Supply Voltage 4.5 5.5 4.5 5.5 V T AMB Ambient Operating Temperature 0 +70 –40 +85 ° C ELECTRICAL CHARACTERISTICS K/B Grades Parameter Test Conditions Min Max Unit V IH Hi-Level Input Voltage 1, 2 @ V DD = max 2.0 V V IH Hi-Level CLK ...
-
Analog Devices ADSP-2183 - page 13
ADSP-2181/ADSP-2183 REV. 0 –13– ESD SENSITIVITY The ADSP-2181 is an ESD (electrostatic discharge) sensitive device. Electrostatic charges readily accumulate on the human body and equipment and can discharge without detection. Permanent damage may occur to devices subjected to high energy electrostatic discharges. The ADSP-2181 features propriet ...
-
Analog Devices ADSP-2183 - page 14
ADSP-2181/ADSP-2183 REV. 0 –14– ADSP-2181 ENVIRONMENTAL CONDITIONS Ambient Temperature Rating: T AMB = T CASE – (PD × θ CA ) T CASE = Case Temperature in ° C PD = Power Dissipation in W θ CA = Thermal Resistance (Case-to-Ambient) θ JA = Thermal Resistance (Junction-to-Ambient) θ JC = Thermal Resistance (Junction-to-Case) Package θ JA ? ...
-
Analog Devices ADSP-2183 - page 15
ADSP-2181/ADSP-2183 REV. 0 –15– t DECAY , is dependent on the capacitive load, C L , and the current load, i L , on the output pin. It can be approximated by the fol- lowing equation: t DECAY = C L •0 . 5 V i L from which t DIS = t MEASURED – t DECAY is calculated. If multiple pins (such as the data bus) are dis- abled, the measurement valu ...
-
Analog Devices ADSP-2183 - page 16
ADSP-2181/ADSP-2183 REV. 0 –16– ADSP-2183–SPECIFICA TIONS RECOMMENDED OPERA TING CONDITIONS K Grade B Grade Parameter Min Max Min Max Unit V DD Supply Voltage 3.0 3.6 3.0 3.6 V T AMB Ambient Operating Temperature 0 +70 –40 +85 ° C ELECTRICAL CHARACTERISTICS K/B Grades Parameter Test Conditions Min Max Unit V IH Hi-Level Input Voltage 1, 2 ...
-
Analog Devices ADSP-2183 - page 17
ADSP-2181/ADSP-2183 REV. 0 –17– MEMORY TIMING SPECIFICATIONS The table below shows common memory device specifications and the corresponding ADSP-2183 timing parameters, for your convenience. Memory ADSP-2183 Timing Device Timing Parameter Specification Parameter Definition Address Setup to t ASW A0–A13, xMS Setup before Write Start WR Low Ad ...
-
Analog Devices ADSP-2183 - page 18
ADSP-2181/ADSP-2183 REV. 0 –18– ( C × V DD 2 × f ) is calculated for each output: # of Pins × C × V DD 2 × f Address, DMS 8 × 10 pF × 3.3 2 V × 33.3 MHz = 29.0 mW Data Output, WR 9 × 10 pF × 3.3 2 V × 16.67 MHz = 16.3 mW RD 1 × 10 pF × 3.3 2 V × 16.67 MHz = 1.8 mW CLKOUT 1 × 10 pF × 3.3 2 V × 33.3 MHz = 3.6 mW 50.7 mW Total pow ...
-
Analog Devices ADSP-2183 - page 19
ADSP-2181/ADSP-2183 REV. 0 –19– ADSP-2183 CAPACITIVE LOADING Figures 17 and 18 show the capacitive loading characteristics of the ADSP-2183. C L – pF RISE TIME (0.4V – 2.4V) – ns 30 0 0 200 25 50 75 100 125 150 175 25 20 15 10 5 T = +85 ° C V DD = 3.0V Figure 17. Typical Output Rise Time vs. Load Capacitance, C L (at Maximum Ambient Oper ...
-
Analog Devices ADSP-2183 - page 20
ADSP-2181/ADSP-2183 REV. 0 –20– ADSP-2181 Parameter Min Max Unit Clock Signals and Reset Timing Requirements : t CKI CLKIN Period 60 150 ns t CKIL CLKIN Width Low 20 ns t CKIH CLKIN Width High 20 ns Switching Characteristics: t CKL CLKOUT Width Low 0.5t CK – 7 ns t CKH CLKOUT Width High 0.5t CK – 7 ns t CKOH CLKIN High to CLKOUT High 0 20 n ...
-
Analog Devices ADSP-2183 - page 21
ADSP-2181/ADSP-2183 REV. 0 –21– ADSP-2181 Parameter Min Max Unit Interrupts and Flag Timing Requirements : t IFS IRQx , FI, or PFx Setup before CLKOUT Low 1, 2, 3, 4 0.25t CK + 15 ns t IFH IRQx , FI, or PFx Hold after CLKOUT High 1, 2, 3, 4 0.25t CK ns Switching Characteristics : t FOH Flag Output Hold after CLKOUT Low 5 0.5t CK – 7 ns t FOD ...
-
Analog Devices ADSP-2183 - page 22
ADSP-2181/ADSP-2183 REV. 0 –22– ADSP-2181/ADSP-2183 Parameter Min Max Unit Bus Request/Grant Timing Requirements : t BH BR Hold after CLKOUT High 1 0.25t CK + 2 ns t BS BR Setup before CLKOUT Low 1 0.25t CK + 17 ns Switching Characteristics : t SD CLKOUT High to xMS , 0.25t CK + 10 ns RD , WR Disable t SDB xMS , RD , WR Disable to BG Low 0 ns t ...
-
Analog Devices ADSP-2183 - page 23
ADSP-2181/ADSP-2183 REV. 0 –23– ADSP-2181 Parameter Min Max Unit Memory Read Timing Requirements : t RDD RD Low to Data Valid 0.5t CK – 9 + w ns t AA A0-A13, xMS to Data Valid 0.75t CK – 10.5 + w ns t RDH Data Hold from RD High 0 ns Switching Characteristics : t RP RD Pulse Width 0.5t CK – 5 + w ns t CRD CLKOUT High to RD Low 0.25t CK – ...
-
Analog Devices ADSP-2183 - page 24
ADSP-2181/ADSP-2183 REV. 0 –24– ADSP-2181/ADSP-2183 Parameter Min Max Unit Memory Write Switching Characteristics : t DW Data Setup before WR High 0.5t CK – 7+ w ns t DH Data Hold after WR High 0.25t CK – 2 ns t WP WR Pulse Width 0.5t CK – 5 + w ns t WDE WR Low to Data Enabled 0 ns t ASW A0-A13, xMS Setup before WR Low 0.25t CK – 6 ns t ...
-
Analog Devices ADSP-2183 - page 25
ADSP-2181/ADSP-2183 REV. 0 –25– ADSP-2181/ADSP-2183 Parameter Min Max Unit Serial Ports Timing Requirements : t SCK SCLK Period 50 ns t SCS DR/TFS/RFS Setup before SCLK Low 4 ns t SCH DR/TFS/RFS Hold after SCLK Low 7 ns t SCP SCLK IN Width 20 ns Switching Characteristics : t CC CLKOUT High to SCLK OUT 0.25t CK 0.25t CK + 10 ns t SCDE SCLK High ...
-
Analog Devices ADSP-2183 - page 26
ADSP-2181/ADSP-2183 REV. 0 –26– ADSP-2181/ADSP-2183 Parameter Min Max Unit IDMA Address Latch Timing Requirements : t IALP Duration of Address Latch 1, 3 10 ns t IASU IAD15–0 Address Setup before Address Latch End 3 5n s t IAH IAD15–0 Address Hold after Address Latch End 3 2n s t IKA IACK Low before Start of Address Latch 1 0n s t IALS Star ...
-
Analog Devices ADSP-2183 - page 27
ADSP-2181/ADSP-2183 REV. 0 –27– ADSP-2181 Parameter Min Max Unit IDMA Write, Short Write Cycle Timing Requirements : t IKW IACK Low before Start of Write 1 0n s t IWP Duration of Write 1, 2 15 ns t IDSU IAD15–0 Data Setup before End of Write 2, 3, 4 5n s t IDH IAD15–0 Data Hold after End of Write 2, 3, 4 2n s Switching Characteristics : t I ...
-
Analog Devices ADSP-2183 - page 28
ADSP-2181/ADSP-2183 REV. 0 –28– ADSP-2181 Parameter Min Max Unit IDMA Write, Long Write Cycle Timing Requirements : t IKW IACK Low before Start of Write 1 0n s t IKSU IAD15–0 Data Setup before IACK Low 2, 3 0.5t CK + 10 ns t IKH IAD15–0 Data Hold after IACK Low 2, 3 2n s Switching Characteristics : t IKLW Start of Write to IACK Low 4 1.5t C ...
-
Analog Devices ADSP-2183 - page 29
ADSP-2181/ADSP-2183 REV. 0 –29– ADSP-2181 Parameter Min Max Unit IDMA Read, Long Read Cycle Timing Requirements : t IKR IACK Low before Start of Read 1 0n s t IRP Duration of Read 15 ns Switching Characteristics : t IKHR IACK High after Start of Read 1 15 ns t IKDS IAD15–0 Data Setup before IACK Low 0.5t CK –10 ns t IKDH IAD15–0 Data Hold ...
-
Analog Devices ADSP-2183 - page 30
ADSP-2181/ADSP-2183 REV. 0 –30– ADSP-2181 Parameter Min Max Unit IDMA Read, Short Read Cycle Timing Requirements : t IKR IACK Low before Start of Read 1 0n s t IRP Duration of Read 15 ns Switching Characteristics : t IKHR IACK High after Start of Read 1 15 ns t IKDH IAD15–0 Data Hold after End of Read 2 0n s t IKDD IAD15–0 Data Disabled aft ...
-
Analog Devices ADSP-2183 - page 31
ADSP-2181/ADSP-2183 REV. 0 –31– 128-Lead TQFP Package Pinout 65 64 102 IRQL1 TFS1/IRQ1 RFS1/IRQ0 103 1 128 39 38 BG EBG BR EBR IS V DD GND D23 IRD IWR GND D22 D21 D20 D18 D19 D17 D16 D15 V DD GND D14 D13 D12 D11 D9 D8 D7 D6 D5 D10 GND D2 D1 D0 D4 D3 V DD GND PF4 PF5 PF6 PF7 IAD0 IAD1 IAD2 IAD3 IAD4 IAD5 GND IAD6 IAD7 IAD8 IAD9 IAD10 IAD11 IAD12 ...
-
Analog Devices ADSP-2183 - page 32
ADSP-2181/ADSP-2183 REV. 0 –32– TQFP Pin Configurations TQFP Pin TQFP Pin TQFP Pin TQFP Pin Number Name Number Name Number Name Number Name 1 IAL 33 A12 65 ECLK 97 D19 2 PF3 34 A13 66 ELOUT 98 D20 3 PF2 35 IRQE 67 ELIN 99 D21 4 PF1 36 MMAP 68 EINT 100 D22 5 PF0 37 PWD 69 EBR 101 D23 6 WR 38 IRQ2 70 BR 102 GND 7 RD 39 BMODE 71 EBG 103 IWR 8 IOMS ...
-
Analog Devices ADSP-2183 - page 33
ADSP-2181/ADSP-2183 REV. 0 –33– OUTLINE DIMENSIONS 128-Lead Metric Thin Plastic Quad Flatpack (TQFP) 65 64 102 103 1 128 39 38 E 3 E 1 E B e D 3 D 1 D TOP VIEW (PINS DOWN) SEATING PLANE L A D A 1 A 2 MILLIMETERS INCHES SYMBOL MIN TYP MAX MIN TYP MAX A 1.60 0.063 A 1 0.05 0.15 0.002 0.006 A 2 1.30 1.40 1.50 0.051 0.055 0.059 D 15.75 16.00 16.25 ...
-
Analog Devices ADSP-2183 - page 34
ADSP-2181/ADSP-2183 REV. 0 –34– 128-Lead PQFP Package Pinout 65 64 96 97 1 33 32 TOP VIEW (PINS DOWN) 128L PQFP (28mm x 28mm) 128 PF1 PF2 PF3 IAL BG EBG BR EBR IS V DD GND D23 IRD IWR GND D22 D21 D20 D18 D19 D17 D16 D15 V DD GND D14 D13 D12 D11 D9 D8 D7 D6 D5 GND D2 D1 D0 D10 D4 D3 V DD GND PF4 PF5 PF6 PF7 IAD0 IAD1 IAD2 IAD3 IAD4 IAD5 GND IAD6 ...
-
Analog Devices ADSP-2183 - page 35
ADSP-2181/ADSP-2183 REV. 0 –35– PQFP Pin Configurations PQFP Pin PQFP Pin PQFP Pin PQFP Pin Number Name Number Name Number Name Number Name 1 PF0 33 PWD 65 EBR 97 D23 2 WR 34 IRQ2 66 BR 98 GND 3 RD 35 BMODE 67 EBG 99 IWR 4 IOMS 36 PWDACK 68 BG 100 IRD 5 BMS 37 IACK 69 VDD 101 IAD15 6 DMS 38 BGH 70 D0 102 IAD14 7 CMS 39 VDD 71 D1 103 IAD13 8 GND ...
-
Analog Devices ADSP-2183 - page 36
ADSP-2181/ADSP-2183 REV. 0 –36– OUTLINE DIMENSIONS 128-Lead Metric Plastic Quad Flatpack (PQFP) 65 64 96 97 1 128 33 32 E 3 E 1 E B e D 3 D 1 D TOP VIEW (PINS DOWN) SEATING PLANE L A D A 1 A 2 MILLIMETERS INCHES SYMBOL MIN TYP MAX MIN TYP MAX A 4.07 0.160 A 1 0.25 0.010 A 2 3.17 3.49 3.67 0.125 0.137 0.144 D, E 30.95 31.20 31.45 1.219 1.228 1.2 ...
-
Analog Devices ADSP-2183 - page 37
ADSP-2181/ADSP-2183 REV. 0 –37– ORDERING GUIDE Ambient Instruction Temperature Rate Package Package Part Number Range (MHz) Description Option* ADSP-2181KST-115 0 ° C to +70 ° C 28.8 128-Lead TQFP ST-128 ADSP-2181BST-115 –40 ° C to +85 ° C 28.8 128-Lead TQFP ST-128 ADSP-2181KS-115 0 ° C to +70 ° C 28.8 128-Lead PQFP S-128 ADSP-2181BS-11 ...
-
Analog Devices ADSP-2183 - page 38
–38– ...
-
Analog Devices ADSP-2183 - page 39
–39– ...
-
Analog Devices ADSP-2183 - page 40
–40– C2144–16–6/96 PRINTED IN U.S.A. ...
¿Tienes una pregunta acerca de Analog Devices ADSP-2183?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Analog Devices ADSP-2183, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Analog Devices ADSP-2183 probablemente compartirá una forma de solucionarlo.