-
CDA FW821 - page 1
Customer Care Department • The Group Ltd. • Harby R oad • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : customer .care@cda.eu W : www .cda.eu FW821 Extra Large Integrated Larder Fridge Manual for Installation, Use and Maintenance ...
-
CDA FW821 - page 2
2 Important The manufacturer cannot be held responsible for injuries or losses caused by incorrect use or installation of this product. Please note that we reserve the right to invalidate the guarantee supplied with this product following incorrect installation or misuse of the appliance. This appliance is not designed to be used by people (includi ...
-
CDA FW821 - page 3
3 This appliance has been manufactured to the strictest standards and complies with all applicable legislation, including Electrical safety (L VD) and Electromagnetic interference compatibility (EMC). Parts intended to come into contact with food conform to EEC/89/109 .4 IMPORT ANT INFORMA TION FOR CORRECT DISPOSAL OF THE PRODUCT IN A CCORD ANCE WI ...
-
CDA FW821 - page 4
4 Before first use Y ou must allow the fridge to settle for at least twenty four hours prior to switching the power on. It is recommended that you clean the interior of the appliance prior to first use, using a solution of bicarbonate of soda and warm water and then thoroughly drying the interior . The fridge may have an odour to it at first use ...
-
CDA FW821 - page 5
5 Use • Never put liquids in the refrigerator uncovered. • Never put hot foods in the refrigerator . W arm food should be allowed to cool to room temperature before being put into the refrigerator . • Nothing should rest against the internal rear wall of the refrigerator , as this will cause frost and possible condensation problems which will ...
-
CDA FW821 - page 6
6 W e recommend initially setting the temperature control in mid range for the first 24 hours then adjusting the temperature up or down from this point as your personal preference. Care and cleaning Always disconnect the appliance from the power before any cleaning or maintenance. • The refrigerator should be cleaned using a solution of bicarbon ...
-
CDA FW821 - page 7
7 T roubleshooting If you have any problems with your appliance, you should check the troubleshooting prior to calling CD A Customer Care to prevent unnecessary service calls and potential cost. If the appliance is not working • Check there is power to the appliance. • The house fuses are intact and the fuse in the plug has not blown. • The t ...
-
CDA FW821 - page 8
8 fig. 2 1770 45 57 545 540 1770- 1788 min. 30 560-570 545 min = airflow If there is water in the lower part of the refrigerator compartment • The drain hole in the channel at the back of the compartment is clear . Please note: The LED lighting cannot be replaced without a service call. If the light fails, contact CD A Customer Care. Installati ...
-
CDA FW821 - page 9
9 V entilation The main consideration when installing any refrigeration unit into a fitted kitchen is ventilation. The heat removed from the cooling compartment needs to be dissipated into the atmosphere. Incorrect ventilation can lead to premature compressor failure, ex cessive power consumption and total system failure. For products intended to ...
-
CDA FW821 - page 10
10 The open channel at the rear is clearly shown. For the correct operation of the appliance it is important that the top of the housing unit is not blocked o . A channel depth of 40-50mm is normal with most units. A hole is shown in the base shelf of the unit; this allows air to be drawn over the compressor & heat ex change. Some installers ...
-
CDA FW821 - page 11
11 R eversing the door It is possible to reverse the door on this appliance, if required. T o do so, follow the steps below: 1. L oosen the top hinge fixing screws and remove the top hinge, taking care to support the weight of the door . 2. Lift the door from the bottom hinge and place on a soft surfaceto protect the door from damage. 3. R efit t ...
-
CDA FW821 - page 12
12 Mounting the Fascia Door • Using a screwdriver , fix the mounting brackets to the appliance door , as shown in figure 5. • Position the appliance within the unit. Ensure that there is a gap of 3 to 4 mm between the non-hinged side and the cabinet wall. • L ocate the slider in the bracket and fix the slider to the fascia door 20 to 22 mm ...
-
CDA FW821 - page 13
13 Electrical Iinformation W arning! This appliance must be earthed. The mains lead of this appliance has been fitted with a BS 1363A 13Amp fused plug. T o change a fuse in this type of plug, follow the steps below: 1. R emove the fuse cover and fuse. 2. Fit replacement 13A fuse, A ST A approved to BS 1362 type, into the fuse cover . 3. R eplace f ...
-
CDA FW821 - page 14
14 As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:- • The wire which is coloured GREEN and YELL O W must be connected to the terminal which is marked with letter (E) or by the Earth symbol or coloured GREEN and YELL O W . • ...
-
CDA FW821 - page 15
15 ...
-
CDA FW821 - page 16
Please contact our Customer Care Department for Service on the details below Customer Care Department • The Group Ltd. • Harby R oad • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www .cda.eu ...
¿Tienes una pregunta acerca de CDA FW821?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con CDA FW821, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con CDA FW821 probablemente compartirá una forma de solucionarlo.