-
Kathrein HDZ 100 - page 1
Installation Manual Caravan roof gland HDZ 100 Protective casing for cable interfaces on the caravan roof for Kathrein rotary antenna systems type CAP series ...
-
Kathrein HDZ 100 - page 2
2 CONTENTS .............................................................................................................................. . 2 FOREIGN LANGUAGE INST ALLA TION MANUALS/SERVICE ...................................................... 3 ADDRESS OF THE SER VICE CENTRE ........................................................................ ...
-
Kathrein HDZ 100 - page 3
3 Dear Customer , Chère Cliente, Cher Client, Gentile cliente, Estimado cliente, GB Y ou can obtain an English version of our installation instructions from our representatives in your country (http://www .kathrein.de/include/kontakte_groups_eng.cfm?kontinent=1&gruppe=SA T) or download one from our homepage (http://www .kathrein.de/en/sat/prod ...
-
Kathrein HDZ 100 - page 4
4 HDZ 100 COMPONENTS/SCOPE OF SUPPL Y • Cover with two gaskets and four captive screws • Sealing plug • Bottom half of the casing with gasket and six plugs • Three fastening screws HDZ 100 SCOPE OF SUPPL Y • Protective casing for cable interfaces on the caravan roof for Kathrein rotary antenna systems type CAP series • Capable of accept ...
-
Kathrein HDZ 100 - page 5
5 PROPER USE The HDZ 100 roof gland protects the cable connection point and the roof gland point when laying cables from CAP systems on the caravan or mobile home roof. The gland seatings are designed for two cables (Ø 5 mm) and one cable (Ø 6.5-7 mm). Any use other than that speci fi ed above will void the warranty or guarantee. The following c ...
-
Kathrein HDZ 100 - page 6
6 SAFETY INSTRUCTIONS - IMPORT ANT NOTES Safety during installation work When carrying out installation work in locations where there is a risk of falling, take appropriate safety precautions, e.g. use of a working platform. Make sure that the vehicle roof is suf fi ciently strong and stable to carry out the installation work (risk of damage or co ...
-
Kathrein HDZ 100 - page 7
7 Cables Lay all cables such that nobody can tread on them or trip over them. When connecting the power cables (receiver and turntable) to the vehicle electrical supply , make sure that the cable polarity is not reversed. If the cable polarity is reversed there is a risk of thermal overload and damage to components when the equipment is powered up! ...
-
Kathrein HDZ 100 - page 8
8 INST ALLA TION EXAMPLES BASIC V ARIANTS Roof gland with cable interface Roof gland without cable interface Cable continuation with cable interface Note: For the CAP 600/700 units there are always two cables emerging from the turntable. For the CAP 900 unit there are always three cables emerging from the turntable. CAP 600 and CAP 700 CAP 600 and ...
-
Kathrein HDZ 100 - page 9
9 • Circular cutter , Ø 38 mm • Cross-head screwdriver for M4 screws • Power drill • T wist drill Ø 2.5 mm • Knife • Round fi le or emery paper • Sika fl ex ® 291 sealant (included in the CAP turntable scope of supply . Comply with the respective safety instructions for the sealant) • If required for the type of installation se ...
-
Kathrein HDZ 100 - page 10
10 INST ALLA TION AND CONNECTION INST ALLA TION STEPS ROOF GLAND V ARIANT 1. In the centre of the intended position of the cable outlet spigot, drill the opening for the cable gland with a circular cutter (Ø: 38 mm). Deburr the hole with a round fi le or emery paper (see illustration on the right). 2. Provisionally insert the casing lower half in ...
-
Kathrein HDZ 100 - page 11
11 INST ALLA TION AND CONNECTION 5. Ensure before starting adhesive work that the temperature of materials to be glued and the adhesive sealant is between +5 °C and +40 °C. Prepare all necessary fastening elements and tools. 6. Prepare the tube of adhesive sealant in accordance with the instructions enclosed with the tube. 7. Apply the sealant al ...
-
Kathrein HDZ 100 - page 12
12 CABLE CONTINUA TION V ARIANT 1. First cut the cylindrical spigot off the underside of the casing. There are two ways of doing this: - use a sharp knife to cut through the wall between the base of the casing and the spigot (see illustration on the right) or 1 1. Use the plugs supplied to seal the cable attachment points that are now not required ...
-
Kathrein HDZ 100 - page 13
13 9. Now open up the break-out in the end face of the cover for the cable outlet (see illustrations on the right). 2. Continue as described in points 3. to 8. of the description for the “roof gland” variant. 10. Now connect the cables from the turntable on the cables from the interior of the vehicle, within the casing (see illustration on the ...
-
Kathrein HDZ 100 - page 14
14 INST ALLA TION AND CONNECTION 1 1. Insert the cable in the seal and push it into the cable clips in the casing (see illustration on the right). 12. Use the plugs attached to seal the cable attachment points that are now not required (see illustration on the right). Do not cut away any plugs that are not required, you will need them if you ever w ...
-
Kathrein HDZ 100 - page 15
15 TECHNICAL DA T A (in mm) 211 38 37 () 65 28,5 90 max. 31 max. 17 20 (3x) 2,5 Schnittstellen: Schutzar t nach EN 60529: IP55 V erpackung: Bruttogewicht: 0,35 kg Nettogewicht: 0,25 kg - Dachbohrung: 38 - Leitungsführungskanal: B =31, H =17 - Kabel: 2x HF 5; 1x DC 6,5 - 7 - Kernbohrung in Unterkonstruktion: 3x 2,5 für Blechschrauben ST3,5x19 - Ei ...
-
Kathrein HDZ 100 - page 16
Internet: http://www .kathrein.de KA THREIN-Werke KG • Anton-Kathrein-Straße 1 - 3 P .O. Box 100 444 • 83004 Rosenheim GERMANY 936.3442/-/0908/ZWT - T echnical data subject to change. FOR YOUR NOTES ...
¿Tienes una pregunta acerca de Kathrein HDZ 100?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Kathrein HDZ 100, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Kathrein HDZ 100 probablemente compartirá una forma de solucionarlo.