-
Husqvarna 924SBE - page 1
924SBE Owner's Manual ...
-
Husqvarna 924SBE - page 2
2 IMPORT ANT Safe Operation Practices for W alk-Behind Snow Throwers This snow thrower is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury . W ARNING: This snow thrower is for use on sidewalks, driveways and other ground level surfaces. Caution should be e ...
-
Husqvarna 924SBE - page 3
3 PRODUCT SPECIFICA TIONS Gasoline Capacity 4.0 Quarts and T ype: Unleaded Regular only Oil T ype SAE 30 (above 40°F) (API SG–SL): SAE 5W-30 or 10W-30 (0° to +40°F) SAE 0W-30 (below 0°F) Oil Capacity: 26 Ounces Spark Plug: Champion RJ19LM (Gap: .030") CONGRA TULA TIONS on your purchase of a new snow thrower . It has been designed, engine ...
-
Husqvarna 924SBE - page 4
4 P ARTS P ACKED SEP ARA TEL Y IN CART ON Read these instructions and this manual in its entirety before you attempt to assemble or operate your new snow thrower . Reading the entire manual will familiar- ize you with the unit, which will assist you in assembly , operation and maintenance of the product. Y our new snow thrower has been as sem bled ...
-
Husqvarna 924SBE - page 5
5 ASSEMBL Y / PRE-OPERA TION NOTE: The multi-wrench may be used for assembly of the chute rotator head to snow thrower and making ad just ments to the skid plates. UNFOLD UPPER HANDLE 1. Raise upper handle to the operating position and tight en handle knobs securely . INST ALL SPEED CONTROL ROD (See Figs. 1 and 2) 1. Remove plastic tie securing rod ...
-
Husqvarna 924SBE - page 6
6 ASSEMBL Y / PRE-OPERA TION INST ALL DISCHARGE CHUTE / CHUTE ROT A TER HEAD (See Fig. 7) NOTE: The multi-wrench provided in your parts bag may be used to install the chute rotater head. 1. Place discharge chute assembly on top of chute base with discharge opening toward front of snow thrower. 2. Position chute rotater head over chute bracket. If n ...
-
Husqvarna 924SBE - page 7
7 OPERA TION KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERA TING YOUR SNOW THROWER. Compare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. These symbols may appear on your snow thrower or in literat ...
-
Husqvarna 924SBE - page 8
8 OPERA TION Choke control - used for starting a cold engine. Drive speed control lever - used to select forward or reverse motion and speed of snow thrower . T raction drive control lever - used to engage power-pro- pelled for ward or reverse motion of snow thrower. Auger control lever - used to engage auger motion (throw snow). Discharge chute co ...
-
Husqvarna 924SBE - page 9
9 The operation of any snow thrower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your snow thrower or performing any ad just - ments or repairs. We recommend standard safe ty glasses or a wide vision safety mask worn over spectacles. HOW TO USE Y ...
-
Husqvarna 924SBE - page 10
10 TO MOVE FOR W ARD AND BACKW ARD (See Fig. 16) SELF-PROPELLING, forward and reverse movement of the snow thrower , is controlled by the traction drive control lever located on the left side handle. • Squeeze traction drive control lever to handle to en gage the drive system. • Release traction drive control lever to stop the forward or revers ...
-
Husqvarna 924SBE - page 11
11 TO ADJUST SKID PLA TES (See Fig. 17) NOTE: The wrench provided in your parts bag may be used to adjust the skid plates. Skid plates are located on each side of the auger housing and adjust the clearance between the scraper bar and the ground surface. Adjust skid plates evenly to proper height for current surface conditions. For removal of snow i ...
-
Husqvarna 924SBE - page 12
12 COLD ST ART - ELECTRIC ST ARTER 1. Insert safety ignition key into the ignition slot until it clicks. DO NOT turn the key . Keep the extra safety ignition key in a safe place. 2. Place throttle control in F AST position. 3. Rotate choke control to FULL position. 4. Connect the power cord to the engine. 5. Plug the other end of the power cord int ...
-
Husqvarna 924SBE - page 13
13 MAINTENANCE LUBRICA TION CHART GENERAL REC OM MEN DA TIONS The warranty on this snow thrower does not cover items that have been sub ject ed to operator abuse or negligence. T o receive full value from the warranty , operator must maintain snow thrower as in struct ed in this manual. Some ad just - ments will need to be made periodically to prop ...
-
Husqvarna 924SBE - page 14
14 MAINTENANCE V- B E LT S Check V -belts for deterioration and wear after every 50 hours of operation and replace if necessary . The belts are not ad just able. Replace belts if they begin to slip from wear . (See “TO REMOVE BEL T COVER” in the Service and Adjustments section of this manual). The V -belts on your snow thrower are of special co ...
-
Husqvarna 924SBE - page 15
15 SER VICE AND ADJUSTMENTS W ARNING: T o avoid serious injury , before performing any service or ad- just ments: 1. Be sure throttle is in STOP position. 2. Remove safety ignition key . 3. Make sure the augers and all mov ing parts have completely stopped. 4. Disconnect spark plug wire from spark plug and place wire where it can not come in contac ...
-
Husqvarna 924SBE - page 16
16 SER VICE AND ADJUSTMENTS TO REPLACE BEL TS (See Fig. 21) The auger and traction drive belts are not adjustable. If the belts are damaged or begin to slip from wear , they should be replaced. It is recommended that the belt(s) be replaced by a qualifi ed service center . NOTE: It is recommended that both the auger and traction drive belt be repl ...
-
Husqvarna 924SBE - page 17
17 ST ORAGE Immediately prepare your snow thrower for storage at the end of the season or if the unit will not be used for 30 days or more. W ARNING: Never store the snow thrower with gaso line in the tank in side a build ing where fumes may reach an open fl ame, spark or pilot light as on a fur nace, water heater , clothes dryer or gas ap pli anc ...
-
Husqvarna 924SBE - page 18
18 Does not start 1. Fuel shut-off valve (if so 1. T urn fuel shut-off valve to OPEN position. equipped) in OFF position. 2. Safety ignition key 2. Insert safety ignition key . is not inserted. 3. Out of fuel. 3. Refi ll fuel tank with fresh, clean gasoline. 4. Throttle in STOP position. 4. Move throttle to F AST position. 5. Choke in OFF position ...
-
Husqvarna 924SBE - page 19
19 SER VICE NOTES ...
-
Husqvarna 924SBE - page 20
20 REP AIR P ARTS AUGER HOUSING / IMPELLER ASSEMBL Y SNOW THROWER - MODEL NO. 924SBE (96193001500), PRODUCT NO. 961 93 00-15 6 6 5 9 9 12 7 7 8 6 11 57 10 10 13 4 14 16 15 36 37 50 47 42 42 44 27 27 43 43 46 38 45 41 40 39 34 32 49 19 48 51 33 35 56 30 31 19 19 55 22 26 25 20 25 26 22 20 18 10 17 17 28 55 28 18 29 29 ...
-
Husqvarna 924SBE - page 21
21 REP AIR P ARTS AUGER HOUSING / IMPELLER ASSEMBL Y SNOW THROWER - MODEL NO. 924SBE (96193001500), PRODUCT NO. 961 93 00-15 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void yo ...
-
Husqvarna 924SBE - page 22
22 REP AIR P ARTS CONTROL P ANEL / DISCHARGE CHUTE SNOW THROWER - MODEL NO. 924SBE (96193001500), PRODUCT NO. 961 93 00-15 1 2 6 7 4 5 6 8 8 19 2 2 32 26 28 27 27 25 20 29 24 14 3 31 30 18 17 10 15 12 21 9 16 14 13 ...
-
Husqvarna 924SBE - page 23
23 REP AIR P ARTS CONTROL P ANEL / DISCHARGE CHUTE SNOW THROWER - MODEL NO. 924SBE (96193001500), PRODUCT NO. 961 93 00-15 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your ...
-
Husqvarna 924SBE - page 24
24 REP AIR P ARTS HANDLES SNOW THROWER - MODEL NO. 924SBE (96193001500), PRODUCT NO. 961 93 00-15 10 11 15 23 22 27 27 22 11 15 12 12 13 15 49 49 48 47 16 17 16 17 15 14 32 31 32 30 31 38 39 40 37 33 35 35 34 34 42 43 44 45 46 46 7 6 36 2 5 5 1 4 4 4 4 8 28 28 9 18 19 26 24 24 25 5 5 ...
-
Husqvarna 924SBE - page 25
25 REP AIR P ARTS HANDLES SNOW THROWER - MODEL NO. 924SBE (96193001500), PRODUCT NO. 961 93 00-15 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO. ...
-
Husqvarna 924SBE - page 26
26 REP AIR P ARTS DRIVE SNOW THROWER - MODEL NO. 924SBE (96193001500), PRODUCT NO. 961 93 00-15 4 4 4 1 2 5 5 1 2 1 20 21 17 19 18 18 7 7 2 2 2 24 23 12 32 27 44 22 16 15 2 4 4 13 1 2 5 5 8 9 10 6 41 14 43 11 35 33 15 41 22 34 29 22 31 26 25 28 30 40 39 38 36 37 33 ...
-
Husqvarna 924SBE - page 27
27 REP AIR P ARTS DRIVE SNOW THROWER - MODEL NO. 924SBE (96193001500), PRODUCT NO. 961 93 00-15 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO. N ...
-
Husqvarna 924SBE - page 28
28 REP AIR P ARTS CHASSIS / ENGINE / PULLEYS SNOW THROWER - MODEL NO. 924SBE (96193001500), PRODUCT NO. 961 93 00-15 6 19 17 10 21 22 23 2 1 3 4 6 7 8 9 12 13 15 27 26 25 24 18 7 20 14 47 47 48 46 44 49 50 51 52 35 55 34 33 32 38 36 41 6 37 39 42 43 11 11 44 45 41 30 29 31 31 58 16 10 21 28 57 6 11 ...
-
Husqvarna 924SBE - page 29
29 REP AIR P ARTS CHASSIS / ENGINE / PULLEYS SNOW THROWER - MODEL NO. 924SBE (96193001500), PRODUCT NO. 961 93 00-15 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warra ...
-
Husqvarna 924SBE - page 30
30 REP AIR P ARTS WHEELS / DECALS SNOW THROWER - MODEL NO. 924SBE (96193001500), PRODUCT NO. 961 93 00-15 3 2 4 4 5 5 6 6 4 4 1 2 5 3 1 4 2 11 0 7 6 8 9 10 ...
-
Husqvarna 924SBE - page 31
31 REP AIR P ARTS WHEELS / DECALS SNOW THROWER - MODEL NO. 924SBE (96193001500), PRODUCT NO. 961 93 00-15 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ...
-
Husqvarna 924SBE - page 32
532 40 57-34 Rev . 1 08.23.06 BY Printed in U.S.A. S E C T I ON 1: L I MIT E D W A R R A N T Y Husqvarna Forest & Garden Company (“Husqvarna”) warrants Husqvarna product to the original pur- chaser to be free from defects in material and workmanship from the date of purchase for the “Warranty Period” of the product as set forth below: L ...
¿Tienes una pregunta acerca de Husqvarna 924SBE?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Husqvarna 924SBE, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Husqvarna 924SBE probablemente compartirá una forma de solucionarlo.