Manual de instrucciones Winegard RM-9946

20 de páginas 0.97 mb
Descargar

Pasar a la página of 20

Summary
  • Winegard RM-9946 - page 1

    1 INSTALLATION/OPERATION MANUAL WINEGARD ® AUTOMATIC RV DIGITAL SATELLITE SYSTEM Model RM-9946 & RM-9947 U.S. PATENT NO. 5,532,710 Made in U.S.A. Winegard Company • 3000 Kirkwood St. • Burlington, IA 52601-2000 319/754-0600 • FAX 319/754-0787 • www.winegard.com Printed in U.S.A. © Winegard Company 2001 2451025 11/01/2001 FOR SLOPED RO ...

  • Winegard RM-9946 - page 2

    2 WARNING: TO REDUCE RISK OF FIRE OR ELECTRICAL SHOCK, DO NOT EXPOSE TO RAIN OR MOISTURE. (Not applicable to mount and antenna) CAUTION: TO REDUCE RISK OF ELECTRICAL SHOCK, DO NOT REMOVE COVER, NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL Dangerous voltage inside enclosure Refer to operating, mainte- nance and safeguard ...

  • Winegard RM-9946 - page 3

    3 Table of Contents OPERATION Introduction ...................................................................................................................................................... 4 Wallplate Control Panel ........................................................................................................ ......................... ...

  • Winegard RM-9946 - page 4

    4 Your new Winegard RV Digital Satellite System is an easy-to-install, easy-to-use satellite TV reception sys- tem. Because it mounts on the top of your recreational vehicle, it goes where you go and provides quality re- ception of digital satellite signal in the continental United States only . Check with your programming pro- vider for exact cove ...

  • Winegard RM-9946 - page 5

    5 ANTENNA POWER Enter Power Stow Manual Cancel Wall plate control panel description 1. DISPLAY: LCD (Liquid Crystal Display) shows instructions and warnings to operator. 12. RED LED: Shows Antenna elevated from stow position (any degree from stow). 2. POWER: Turns system on or off when pressed. To turn On, hold down one second; to turn Off, hold do ...

  • Winegard RM-9946 - page 6

    6 Automatic System Operation After parking and leveling vehicle, look for trees, buildings, hills or mountains that might block the satellite signal. ABOUT YOUR RECEIVER: If you have a DISH Network TM receiver, be sure your system (RM-9946) is set to receive DISH Network satellites. If you have a DIRECTV ® receiver, be sure your system (RM-9946) i ...

  • Winegard RM-9946 - page 7

    7 DON’T UNDERSTAND A MENU? If you see a menu in the display you do not under- stand, press POWER for two seconds to exit that menu. NOTE 1: The system can move directly to any of the available satellites, if you have a clear view, after the initial search routine at a location. The display will show the message “Pick a sat < > ”. It rem ...

  • Winegard RM-9946 - page 8

    8 Manual Operation ANTENNA POWER Enter Power Stow Manual Cancel Wall Plate Controller At any time during any operation, the system may be put in manual control operation mode by pressing the MANUAL button on the wall plate controller. WHEN USING THE MANUAL MODE, THE SYSTEM WILL LOSE INFORMATION. You will not be able to move directly to a satellite ...

  • Winegard RM-9946 - page 9

    9 Parts/Specifications/Warranty Electronics Specifications Primary Power ................................. +12 VDC Power Consumption ........................... 3 amps Operating Temperature Interior ................................... 32° to 120°F Exterior ............................... -10° to +130°F Humidity ........................ 90% nonc ...

  • Winegard RM-9946 - page 10

    10 Installation requirements FIGURE 1 FIGURE 3 To install the Winegard Automatic Digital Satellite Dish, check with your RV dealer or manufacturer. Your RV may already be pre-wired for this system, and/or may have a reinforced roof area available. 1. Choose a location on the roof that will allow the dish to raise and rotate without interference fro ...

  • Winegard RM-9946 - page 11

    11 1. Position the roof template on the vehicle roof and drill 1/8” holes for the screws. DO NOT drill clear through into interior of vehicle . The screws fasten mount to the roof only. Be sure the roof can securely hold system. 2. Place base plate gasket under the base before screwing unit down. Secure the base plate of the motorized assembly to ...

  • Winegard RM-9946 - page 12

    12 FIGURE 6 CENTER LINE OF COACH ROOF The length of this cable MUST BE 53 inches from back of electronics housing to clamp. NO CLAMPS ALONG THIS 53” LENGTH! FRONT OF VEHICLE First cable clamp here! CENTER LINE OF COACH ROOF DRIVER SIDE PASSENGER SIDE 16” from front center edge of mount base Cable-entry plate Cable-en- try plate The length of th ...

  • Winegard RM-9946 - page 13

    13 8. Assemble dish and backup structure using bolts and nuts provided, Figure 9. 9. Install cover using the following steps. Refer to Figure 10 for parts. • Press nylon inserts (# 4) into square holes in bracket (# 5). • Slide bracket onto unit. Dish must be in stowed position . • Fasten bracket to turret using threading cutting screws (# 2) ...

  • Winegard RM-9946 - page 14

    14 Mounting interior wall plate controller Inside your vehicle, choose a convenient location for the wall plate controller. Consider wiring layout, ease of viewing the information on the readout and distance from your tele- vision set. The wall plate uses only 8-conductor cable. Power goes to unit on roof. 1. Install the 8-conductor RJ-45 type cabl ...

  • Winegard RM-9946 - page 15

    15 Wiring Wiring the system: This unit requires a +12 VDC fused circuit. Unit draws up to 3 amps. The unit uses sophisti- cated microprocessor technology and needs “clean” (filtered) power to function properly. DO NOT USE power designated to operate a +12 VDC lighting circuit from the con- verter, or a converter that does not have a battery con ...

  • Winegard RM-9946 - page 16

    16 46 cm Reflector, White P.N. 2745282 (4) Flat Head Bolts (White) P.N. 2160362 LB-1000: STANDARD SINGLE LNBF LB-2000: OPTIONAL DUAL LNBF * Roller P.N. 2200460 Hex Head Bolt 1/4-20 xx 2.5" P.N. 2160237 Nylock Nut 14 - 20 P.N. 2160220 (not shown) Feed Arm P.N. 2744946 Backup Frame P.N. 2744939 Pivot Bracket P.N. 2744945 Pin, 1/4 x 3.375" l ...

  • Winegard RM-9946 - page 17

    17 Spring P.N. 2160818 Electronics top housing, P.N. 3100675 includes screws, P.N. 2160154 Electronics bottom housing only (P.N. 3100676) Gasket P.N. 2240056 Seal P.N. 2200852 Pivot Shaft P.N. 2590344 Roll Pin P.N. 2160842 Rotate Gear P.N. 2200469 Hub P.N. 3100736 Worm/Shaft Assem- bly P.N. 2754099 Motor Housing P.N. 3200260 Motor Housing Gasket P. ...

  • Winegard RM-9946 - page 18

    18 TURRET ASSEMBLY Screw 10-32 x 3/8” (10) P.N. 2160197 Screw, Motor Housing (4) P.N. 2160195 Wire Clamp (2) P.N. 3720053 Down Limit Switch Bracket (w/o switch) P.N. 3200263 Rotate Motor Gear P.N. 2200468 Idler Gear P.N. 2200467 Pivot Bushing P.N. 2200470 Elevating Gear P.N. 2200464 Shoulder Bolt P.N. 2160355 Turret Assembly (4) Hex Head Screw(s) ...

  • Winegard RM-9946 - page 19

    19 Troubleshooting the system Some of the problems we are troubleshooting here are marked with this symbol. For these problems, we advise you to seek professional service. Contact the retailer or dealer where you purchased this sys- tem, or call Winegard Technical Support at 1/800/-788-4417, Monday through Friday, 7:00 a.m. to 4:00 p.m., Central Ti ...

  • Winegard RM-9946 - page 20

    20 Troubleshooting tips 1. Check fuse on supply circuit (power source for system). If +12 VDC is present, check the mo- torized unit on roof. Remove white plastic cover on the mount. Remove electronics housing cover and check the main board, J8 connector, for +12 VDC and ground. If there is voltage present and the cable harness is not damaged, cont ...

Fabricante Winegard Categoría Satellite TV System

Los documentos del dispositivo Winegard RM-9946 que obtenemos del fabricante se pueden dividir en varios grupos. Entre ellos están::
- dibujos técnicos Winegard
- manuales de instrucciones RM-9946
- hojas de producto Winegard
- folletos informativos
- o etiquetas energéticas Winegard RM-9946
Todos son importantes, pero lo más importante desde el punto de vista del usuario de un dispositivo lo encontraremos en el manual de instrucciones Winegard RM-9946.

Un conjunto de documentos determinado como manual de instrucciones se divide también en tipos más detallados, tales como: instrucciones de montaje Winegard RM-9946, instrucciones de servicio, instrucciones cortas o instrucciones de usuario Winegard RM-9946. Dependiendo de la situación debes buscar el documento que necesitas. En nuestra página puedes consultar el manual de instrucciones más popular del producto Winegard RM-9946.

Manuales de instrucciones parecidos

El manual de instrucciones del dispositivo Winegard RM-9946, ¿cómo debería ser?
El manual de instrucciones, también determinado como el manual de usuario o simplemente instrucciones, es un documento técnico que tiene como objetivo ayudar a los usuarios a utilizar Winegard RM-9946. Las instrucciones normalmente las realiza un escritor técnico pero en un lenguaje comprensible para todos los usuarios de Winegard RM-9946.

El manual de instrucciones completo de Winegard debe contener unos elementos básicos. Una parte de ellos es menos importante, como por ejemplo: la portada / la página principal o las páginas de autor. Sin embargo, lo demás debe facilitarnos la información más importante desde el punto de vista del usuario.

1. Introducción y pistas sobre cómo orientarse con el manual Winegard RM-9946 - Al principio de cada manual se deben encontrar las indicaciones acerca de la manera de usar un manual de instrucciones. Debe contener información sobre dónde encontrar el índice Winegard RM-9946, preguntas frecuentes o problemas más comunes – son los apartados más buscados por los usuarios de cada manual de instrucciones.
2. Índice - listados de todos los consejos acerca de Winegard RM-9946 que encontraremos en el documento
3. Consejos de uso de las funciones básicas del dispositivo Winegard RM-9946 - que deben facilitarnos los primeros pasos durante el uso de Winegard RM-9946
4. Troubleshooting - una secuencia sistematizada de acciones que nos ayudará a diagnosticar los problemas más importantes con Winegard RM-9946
5. FAQ - las preguntas frecuentes
6. Datos de contacto Información acerca de cómo encontrar los datos de contacto del fabricante / servicio de Winegard RM-9946 en cada país si no somos capaces de solucionar el problema por nuestra cuenta.

¿Tienes una pregunta acerca de Winegard RM-9946?

Utiliza el formulario que se encuentra abajo

Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Winegard RM-9946, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Winegard RM-9946 probablemente compartirá una forma de solucionarlo.

Copia el texto de la imagen

Comentarios (0)