-
Intel EE110EM - page 1
Intel Express 10/100 Stackable Hub Fiber and Ethernet Modules User Guide ...
-
Intel EE110EM - page 2
Copyright © 1997, Intel Corporation. All rights reserved. Intel Corporation, 5200 NE Elam Young Parkway, Hillsboro OR 97124-6497 Intel Corporation assumes no responsibility for errors or omissions in this manual. Nor does Intel make any commitment to update the information contained herein. * Other product and corporate names may be trademarks of ...
-
Intel EE110EM - page 3
1 Xmt Link Rcv Coll 1. Turn off the power, then unscrew and remove the panel from an expansion slot on the Express 10/100 Stackable Hub. 2. Plug either the Ethernet Module or the Fiber Module into a slot, using the retaining screws to secure the module to the hub. 3. Plug a device in and check the LEDs for a link. You’re done. Quick Start Expansi ...
-
Intel EE110EM - page 4
3 Contents Overview .................................................................................................................................................. 3 Ethernet Module ....................................................................................................................................... 4 Bridging 10 and 100 Mbps hu ...
-
Intel EE110EM - page 5
4 Ethernet Module The Ethernet Module acts as a switch port plugged into an Express 10/100 Stackable Hub. The Ethernet Module • bridges Express 10/100 Stackable Hubs running at 10 Mbps to hubs running at 100 Mbps. • connects Express10/100 Stackable Hubs running at 100 Mbps to each other with TPE cable (creating separate collisions domains). • ...
-
Intel EE110EM - page 6
5 Example configurations These two example configurations show the combinations of duplex and speed LEDs. Bridging hubs running at 100 Mbps to hubs at 10 Mbps This Ethernet Module is plugged into a hub running at 100 Mbps. The module is then connected to a 10 Mbps hub by CAT 3, 4, or 5 TPE cable. Bridging hubs running at 10 Mbps to hubs at 100 Mbps ...
-
Intel EE110EM - page 7
6 Connecting 100 Mbps hubs with TPE cab le Class I hubs, such as the Intel Express 10/100 Stackable Hub, cannot be directly connected with TPE cable when running at 100 Mbps. However, since the Ethernet Module acts as a switched port on a hub, you can use it to connect to another 100 Mbps hub with TPE cable. Each hub or hub stack is a separate coll ...
-
Intel EE110EM - page 8
7 NOTE A long press is held for 2 seconds or more. A short press is held for less than 2 seconds. Connecting to a de vice at full-duple x Express 10/100 Stackable Hubs operate at half-duplex. The only way to connect to a device at full-duplex is with an Ethernet Module. Connecting to a switch at full-duplex Not all device manufacturers implement au ...
-
Intel EE110EM - page 9
8 Connecting to a server at full-duplex This is an Ethernet Module plugged into a hub running at 10 or 100 Mbps. The module is then connected to a server with an Intel EtherExpress™ PRO/100 LAN Adapter using CAT 5 TPE cable. Use the MDI-X connector on the Ethernet Module. You don’t need to configure the Ethernet Module or the LAN adapter to est ...
-
Intel EE110EM - page 10
9 Under standing Ethernet Module LEDs The LEDs on the Ethernet Module provide information about the module’s configuration and status. Port LEDs The LEDs above a port on the Ethernet Module provide information about the port’s configuration and status. Green LED (left side) Amber LED (right side) LED Status Meaning Green Solid Port has a link. ...
-
Intel EE110EM - page 11
10 Change duplex button and LEDs You can determine the Ethernet Module’s duplex configuration and status from the duplex LEDs. Use the Change duplex button to cycle among duplex modes. Attach any Express 10/100 Stackable Hub to the Ethernet Module and the module will automatically negotiate the correct duplex setting (always half-duplex). The def ...
-
Intel EE110EM - page 12
11 Change speed button and LEDs You can determine the speed of the connection between the Ethernet Module and device from the speed LEDs. Use the Change speed button to cycle among speed settings. Attach any Express 10/100 Stackable Hub to the Ethernet Module and the module will automatically negotiate the correct speed. The default speed setting i ...
-
Intel EE110EM - page 13
12 NOTE At half-duplex, you can con- nect hubs up to 160 meters apart. At full-duplex, you can con- nect hubs up to 2 km apart. Fiber Module The Fiber Module acts as a switched port plugged into an Express 10/100 Stackable Hub. The Fiber Module • connects an Express 10/100 Stackable Hub running at 100 Mbps to another hub or other device beyond th ...
-
Intel EE110EM - page 14
13 NOTE A long press is held for 2 seconds or more. A short press is held for less than 2 seconds. Connecting to a de vice at full-duple x Not all device manufacturers implement auto-negotiation of duplex mode. To ensure the Fiber Module connects to the device at full- duplex, force the duplex mode to full-duplex. To force the duplex mode, use the ...
-
Intel EE110EM - page 15
14 Connecting to a switch at full-duplex Fiber Module Auto-negotiate Full-duplex Half-duplex Change duplex Xmt Link Rcv Coll TX RX This is a Fiber Module plugged into a hub running at either 10 or 100 Mbps. The module is then connected to an Intel Express 10/100 Fast Ethernet Switch at full-duplex using 62.5/125-micron fiber optic cable. The module ...
-
Intel EE110EM - page 16
15 Under standing Fiber Module LEDs The LEDs on the Fiber Module provide information about the module’s configuration and status. Duplex LEDs You can determine the Fiber Module’s duplex configuration and status from the duplex LEDs. Use the Change duplex button to cycle among duplex modes. LED Status Meaning Auto-negotiate Solid Module is set t ...
-
Intel EE110EM - page 17
16 Transmit/Receive/Link/Collision LEDs LED Status Meaning Xmt (transmit) Blinking green Port is transmitting data. Off Port is not transmitting data. Rcv (receive) Blinking green Port is receiving data. Off Port is not receiving data. Link Solid green Port has a link. Off No link detected. Coll (collision) Blinking amber Collisions are detected. O ...
-
Intel EE110EM - page 18
17 Limited Hardware Warranty Intel warrants to the original owner that the hardware product delivered in this package will be free from defects in material and workmanship for three (3) years following the latter of: (i) the date of purchase only if you register by returning the registration card as indicated thereon with proof of purchase; or (ii) ...
-
Intel EE110EM - page 19
18 Federal Communications Commission (FCC) Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment ...
-
Intel EE110EM - page 20
19 WARNUNG Das System wurde für den Betrieb in einer normalen Büroumgebung entwickelt. Der entwickelt. Der Standort sollte: · sauber und staubfrei sein (Hausstaub ausgenommen); · gut gelüftet und keinen Heizquellen ausgesetzt sein (einschließlich direkter Sonneneinstrahlung); · keinen Erschütterungen ausgesetzt sein; · keine starken, von e ...
-
Intel EE110EM - page 21
20 World Wide Web & Internet FTP Intel BBS Access Intel’s World Wide Web home page Use Intel’s Bulletin Board. Dial in by or download information using modem at 8-N-1, and up to 14.4 Kbps. anonymous FTP. T roubleshooting ✓ ✓ ✓ ✓ ✓ Software updates ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ Installation notes ✓ ✓ ✓ ✓ ✓ Produ ...
¿Tienes una pregunta acerca de Intel EE110EM?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Intel EE110EM, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Intel EE110EM probablemente compartirá una forma de solucionarlo.