-
Grizzly G1014ZX - page 1
COPYRIGHT © MARCH, 2008 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. #BL10589 PRINTED IN TAIWAN Wh at Ch an ge d? W e ha ve added a sleev e guard to the sander to help reduce the risk of entanglement. The sleev e guard M UST be install ...
-
Grizzly G1014ZX - page 2
In tr od uc ti on The Mod el G 1 01 4ZX is t he same sander as the Model G 1 0 1 4Z with t he addition of the c abinet stand. Please use the includ ed G 1 0 1 4Z manual for refe rence and for ordering par ts that are not listed o n the back of t his inser t. As se mb ly 1. Insert 5 ⁄ 16 -18 x 1" hex bolts into each of the rubber feet. 2. Sec ...
-
Grizzly G1014ZX - page 3
G1014ZX Replacement Parts NOTICE All parts for the Model G1014ZX, except those shown above, are the same as the Model G1014Z. Therefore, please use ...
-
Grizzly G1014ZX - page 4
COMBINATION SANDER MODEL G1014Z INSTRUCTION MANUAL COPYRIGHT © 1992 BY GRIZZLY INDUSTRIAL, INC. REG.# TX 3 360 514 WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. REVISED APRIL, 1997. PRINTED IN USA ...
-
Grizzly G1014ZX - page 5
...
-
Grizzly G1014ZX - page 6
G1014Z Combination Sander -1- Table Of Contents PAGE 1. SAFETY ....................................................................................................................2 SAFETY RULES FOR ALL TOOLS ....................................................................2 ADDITIONAL SAFETY INSTRUCTIONS FOR SANDERS ............................. ...
-
Grizzly G1014ZX - page 7
-2- G1014Z Combination Sander WARNING: For Your Own Safety Read Instruction Manual Before Operating Sander Safety Instructions For Power Tools These safety rules cannot cover every situation in a work shop. Consider your conditions when setting up or operating your jointer. SECTION 1: SAFETY a) Always wear eye protection. b) When belt sanding, supp ...
-
Grizzly G1014ZX - page 8
G1014Z Combination Sander -3- Additional Safety Instructions For Sanders 17. USE RECOMMENDED ACCESSORIES. Consult the owner’s manual for recommend- ed accessories. The use of improper acces- sories may cause risk of injury to persons. 18. CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefull ...
-
Grizzly G1014ZX - page 9
-4- G1014Z Combination Sander Figure 1. Grounded Outlet Box Current Carrying Prongs Grounding Blade Is Longest Of the Three Blades Under no circumstances should the grounding pin from any three-pronged plug be removed. If it will not fit the outlet, have the proper outlet installed by a qualified electrician. Check with a qualified electrician or o ...
-
Grizzly G1014ZX - page 10
G1014Z Combination Sander -5- We are proud to bring you the Model G1014Z Combination Sander. The Model G1014Z is part of a growing Grizzly family of fine woodworking machinery. When used according to the guide- lines set forth in this manual, you can expect years of trouble-free, enjoyable operation and proof of Grizzly’s commitment to customer s ...
-
Grizzly G1014ZX - page 11
-6- G1014Z Combination Sander Contents of the Bolt Bag QTY. DESCRIPTION LOCATION 16 5 ⁄ 16 ''-18 x 1 ⁄ 2 '' Carriage Bolts Stand 16 5 ⁄ 16 '' Flat Washers Stand 16 5 ⁄ 16 ''-18 Hex Nuts Stand 4 5 ⁄ 16 ''-18 x 1 ⁄ 2 '' Hex Bolts Stand/Base 4 5 ⁄ 16 '' Flat Washers St ...
-
Grizzly G1014ZX - page 12
G1014Z Combination Sander -7- Clean up The work table and other unpainted parts of the Model G1014Z are coated with a waxy oil that protects them from corrosion during shipment. Remove the protective coating with mineral spir- its and cloth rags. Do not use gasoline or other petroleum based solvents because of their extremely low flash points. Do n ...
-
Grizzly G1014ZX - page 13
-8- G1014Z Combination Sander Order Of Assembly SECTION 4: ASSEMBLY Most of your Combination Sander has been assembled at the factory. The few remaining pieces will go together quickly and should be done in the following order: 1. Stand 2. Mounting Sanding Unit 3. Attaching the Back Stop 4. Attaching Sanding Disc 5. Mounting the Work Table Note: Al ...
-
Grizzly G1014ZX - page 14
Figure 3. G1014Z Combination Sander -9- Figure 4. 3. Bolt the shorter upper and lower braces to one of the 2 stand sub-assemblies. Figure 4. 4. Now attach the other sub-assembly to the ends of the short braces. Tighten down all the stand bolts at this time. Figure 5. Figure 5. 2. Attach the longer upper and lower cross braces to 2 of the stand legs ...
-
Grizzly G1014ZX - page 15
-10- G1014Z Combination Sander Figure 7. 5. At this point, install the back stop, using the Hex Bolt and Washer as shown in Figure 7. Figure 8. 4. Install the Sanding Disc as shown in Figure 7. Make sure the Setscrew is lined up on the flat spot on the drive shaft. Figure 6. Sanding Unit 1. Set the Sanding Unit on the Stand, carefully aligning the ...
-
Grizzly G1014ZX - page 16
G1014Z Combination Sander -11- Figure 9. Figure 10. 6. Now install the Dust Port using the Hex Bolts and Washers as shown in Figure 9. 7. The last step involves mounting the working table. Loosen the two setscrews in the cast iron base. Insert the table support rod into its hole, making sure the flat portion of the shaft is facing the setscrews. Ti ...
-
Grizzly G1014ZX - page 17
-12- G1014Z Combination Sander 2. Turn the knob approximately 1 ⁄ 4 turn clock- wise to move the belt towards the tracking knob, counter-clockwise to move the belt away. 3. Turn the machine on and off again quickly to see if the tracking has improved. If not, repeat step 1. If tracking is improved move to step 4. 4. Now with the sander running, a ...
-
Grizzly G1014ZX - page 18
G1014Z Combination Sander -13- 3. Tighten hex bolt, PN # 91 and run the sander to adjust the tracking if necessary. 4. Try aggressively sanding a piece of scrap wood. If the tracking is not significantly affected and the belt does not slip on the drum, your belt tension is correct. Belt Tensioning Correct belt tension will insure that your sander f ...
-
Grizzly G1014ZX - page 19
-14- G1014Z Combination Sander Figure 18. Setup for vertical sanding. 2. The Sanding Disc Table can also be moved to become a work table for belt sanding. Simply remove the Table Support Shaft from the base and insert it into the mounting bracket behind the motor. The Bracket’s location is shown in Figure 17. Vertical Positioning The 6" belt ...
-
Grizzly G1014ZX - page 20
G1014Z Combination Sander -15- Figure 19. Changing Discs To replace the sanding disc: 1. Remove the Working Table. 2. Remove the Cover Knob and open the Cover Door. 3. Peel off the old Sanding Disc. Remove the backing from the new Disc, center it and press it firmly into place. 4. It may become necessary to remove the Cast Iron Disc from the Motor ...
-
Grizzly G1014ZX - page 21
-16- G1014Z Combination Sander Horizontal Sanding 1. Turn the sander on and allow the belt to reach full speed. 2. Place the workpiece flat on the belt. Be sure to hold the work securely with both hands. Place one hand at the end of the workpiece to feed it against the rotation of the belt, and one hand lightly on top of the piece to ensure adequat ...
-
Grizzly G1014ZX - page 22
G1014Z Combination Sander -17- Curved Sanding To sand curves, use the end of the belt arm. Hold the workpiece firmly and apply light, even pres- sure to the belt. To avoid excessive loading of the belt in one area, move workpiece slowly across entire surface of belt. Figure 21. Figure 21. Disc Sanding 1. Loosen table lock knob and tilt work table t ...
-
Grizzly G1014ZX - page 23
-18- G1014Z Combination Sander SECTION 7: MAINTENANCE Lubrication V- Belt Your combination sander is equipped with shield- ed and pre-lubricated ball bearings and require no lubrication for the life of the bearings. All bear- ings are common sizes and are readily available from a local bearing supply house or our Service Department. Without proper ...
-
Grizzly G1014ZX - page 24
G1014Z Combination Sander -19- The following pages contain general machine specifications, parts diagram and list and Warranty/Return information for your Model G1014Z Combination Sander. If you need parts or help in assembling your machine, or if you need operational information, we encourage you to call our Service Department. Our trained service ...
-
Grizzly G1014ZX - page 25
-20- G1014Z Combination Sander Machine Data GRIZZLY MODEL G1014Z COMBINATION SANDER Design Type .......................................................................................................................... Floor Model Overall Dimensions and Specifications: Base ........................................................................... ...
-
Grizzly G1014ZX - page 26
1 2 94 98 99 86A 100 107 108 3 5 96 96 95 12 11 4 6 13 9 8 39 103 15 7 A 2 2 3 3 59 62A 106 89 62A 116 115 114 64 105 105 82A 85A 102 81A 83A 101 87A 88A 84A 92 91 B B 106 89 G1014Z Combination Sander -21- ...
-
Grizzly G1014ZX - page 27
70 43 77 57 56 49 27 50 97 12 71 53A 90 41 41 13 A 37 80 52 25 69 27 28 20 29 33 33 31 31 25 25 26 26 27 13 32 24 97 14 28 10 10 44 23 30 10 19 42 10 21 22 34 35 97 32 32 42 36 97 40 93 18 -22- G1014Z Combination Sander ...
-
Grizzly G1014ZX - page 28
G1014Z Combination Sander -23- 32 112 104 110 111 113 109 12 13 65 65 65 12 13 58 41 13 13 12 12 13 12 13 ...
-
Grizzly G1014ZX - page 29
REF PART # DESCRIPTION REF PART # DESCRIPTION -24- G1014Z Combination Sander 57 P1014057 SUPPORT 5 ⁄ 8 ''-11 x 9'' 58 P1014058 FOOT 59 P1014059 IDLER ROLLER SHAFT 62B P1014062B ROLLER ADJ BAR 64 P1014064 IDLER ROLLER 65 PCB05 CARRIAGE BOLT 5 ⁄ 16 -18 x 3 ⁄ 4 '' 69 P1014069 MITER BODY 70 P1014070 SCALE 71 P1014071 ...
-
Grizzly G1014ZX - page 30
G1014Z Combination Sander -25- Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole writte ...
¿Tienes una pregunta acerca de Grizzly G1014ZX?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Grizzly G1014ZX, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Grizzly G1014ZX probablemente compartirá una forma de solucionarlo.