-
Makita 9227C - page 1
INSTR UCTION MANU AL W ARNING: F or your personal saf ety , READ and UNDERST AND bef ore using. SA VE THESE INSTR UCTIONS FOR FUTURE REFERENCE. www .makitatools.com Electr onic Sander P olisher 180 mm (7”) MODEL 9227C MODEL 9227CY 003430 ...
-
Makita 9227C - page 2
2 SPECIFICATIONS • Manuf acturer reser ves the right to change specifications without notice. • Specifications ma y differ from country to countr y . GENERAL SAFETY R ULES USA001-2 (F or All T ools ) W ARNING: Read and understand all instructions. F ailure to f ollow all instructions listed below , ma y result in electr ic shoc k, fire and/or s ...
-
Makita 9227C - page 3
3 5. A void body contact with gr ounded sur- faces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is grounded. 6. Do not expose power tools to rain or wet conditions. W ater enter ing a po wer tool will increase the risk of electric shock. 7. Do not abuse the cor d. Never use the cord t ...
-
Makita 9227C - page 4
4 SER VICE 23. T ool ser vice m ust be performed only by qualified repair personnel. Service or main- tenance performed by unqualified personnel could result in a risk of injur y . 24. When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized par ts or f ailure to ...
-
Makita 9227C - page 5
5 An adapter Fig. “B” and “C” is av ailable f or connecting Fig. “A” type plugs to two-prong receptacles. The g reen-colored r igid ear , lug, etc., e xtending from the adapter must be con- nected to a permanent ground, such as a proper ly g rounded outlet box. SPECIFIC SAFETY R ULES USB047-3 DO NO T let comf or t or familiarity with pr ...
-
Makita 9227C - page 6
6 9. Do not leave the tool running. Operate the tool only when hand-held. 10. Do not touch the w orkpiece immediately after operation; it may be e xtremely hot and could burn y our skin. 11 . Check that the w orkpiece is properly sup- ported. 12. Pa y attention that the wheel continues to rotate after the tool is s witched off. 13. This tool has no ...
-
Makita 9227C - page 7
7 FUNCTIONAL DESCRIPTION CA UTION: • Alwa ys be sure that the tool is switched off and unplugged bef ore adjusting or checking function on the tool. Shaft lock CA UTION: • Ne ver actuate the shaft lock when the spindle is moving. The tool ma y be damaged. Press the shaft lock to pre vent spindle rotation when install- ing or removing accessorie ...
-
Makita 9227C - page 8
8 Ref er to the table f or the relationship between the number settings on the dial and the appro ximate tool speed. CA UTION: • If the tool is operated continuously at lo w speeds for a long time, the motor will get o verloaded, resulting in tool malfunction. • The speed adjusting dial can be turned only as far as 6 and back to 1. Do not f orc ...
-
Makita 9227C - page 9
9 Installing side grip (handlle) (For 9227CY only) CA UTION: • Alwa ys be sure that the side grip is installed securely bef ore operation. Screw the side grip securely on the position of the tool as shown in the figure. Installing or removing the w ool bonnet (optional accessory) T o install the wool bonnet, first remove all dirt or foreign mat- ...
-
Makita 9227C - page 10
10 OPERA TION P olishing operation CA UTION: • Alwa ys wear saf ety glasses or a face shield during operation. Hold the tool firmly . T urn the tool on and then apply the wool bonnet to the workpiece. In general, keep the w ool bonnet at an angle of about 15 degrees to the workpiece surf ace. Apply slight pressure only . Excessiv e pressure will ...
-
Makita 9227C - page 11
11 Replacing carbon brushes Remov e and check the carbon brushes regularly . Replace when they we ar down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced at the same time. Use only iden- tical carbon brushes. Use a screwdriv er to remove the brush holder caps. T ake out the wo ...
-
Makita 9227C - page 12
Memo 12 ...
-
Makita 9227C - page 13
13 First-Class Postage Required Post Office will not deliver without proper postage. Makita U .S.A., Inc. 14930 Nor tham Street La Mirada, CA 90638-5753 Fold Cut ...
-
Makita 9227C - page 14
14 1. This product was pur chased from: Home Center Hardware/Lumber Store T ool Distributor Industrial Supply Construction Supply Other ( ) 3. Ho w did you learn about this product: Magazine F rom Dealer Newspaper Store Display Catalog Radio Exhibition F rom Friend Previous Usage Other ( ) 2. Use of the pr oduct is intended for: Construction T rade ...
-
Makita 9227C - page 15
15 F A CT OR Y SER VICE CENTERS 1-800-4-MAKIT A RET AIN THIS POR TION FOR Y OUR RECORDS ARIZONA 3707 E. Broadway Rd., Ste. 6 Phoenix, AZ 85040 (602) 437-2850 CALIFORNIA 41850 Christy St. Fremont, CA 94538-5107 (510) 657-9881 14930 Northam St. La Mirada, CA 90638-5753 (714) 522-8088 1970 Fulton Av enue Sacramento , CA 95825 (916) 482-5197 7674 Clair ...
-
Makita 9227C - page 16
W ARNING Some dust created by po wer sanding, sawing, g r inding, drilling, and other construction activities contains chemicals known to the State of Calif or nia to cause cancer , bir th def ects or other reproductive harm. Some e xamples of these chemicals are: • lead from lead-based paints, • cr ystalline silica from bricks and cement and o ...
¿Tienes una pregunta acerca de Makita 9227C?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Makita 9227C, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Makita 9227C probablemente compartirá una forma de solucionarlo.