-
iHome IP43 IP43 - page 1
Model iP43 FM alarm clock radio with pillow shaker Questions? Visit www.ihomeaudio.com iP43 IB in USA English version Print color : Black text on white paper Size of manual: 178mmW x 178mmH Sept 2,2010 ...
-
iHome IP43 IP43 - page 2
Table of Contents Quic k Sta rt .........................................................................................................................................................................1 Cont rols and I ndic ator s ....................................................................................................................... ...
-
iHome IP43 IP43 - page 3
Attach AC adaptor cable to DC jack on back of the iP43 and plug the other end into a working outlet. 1 Select the dock insert for your iPhone or iPod ® model from the table below and place insert in dock. NOTE: If you do not have an insert for your iPhone/iPod, please visit www .ihomeaudio.com or call iHome toll free at 1-800-288-2792 to purchase ...
-
iHome IP43 IP43 - page 4
2 Controls and Indicators Time Zone Button Time Set/ Sync Button DST switch Pillow Shaker Jack Snooze/Dimmer Button Alarm 2 Button Alarm 1 Button V olume Wheel Preset Buttons 1-6 Sleep Button Set Wheel EQ Button Dock Radio Button Alarm Reset / Power Button Rear Panel Top Panel Play/Pause Button AC Adaptor Jack FM antenna shaker time zone DST -1 +1 ...
-
iHome IP43 IP43 - page 5
Controls and Indicators On/OFF Switch Snooze Button Pillow Shaker Line-in Plug 3 wake to iP43 Display Alarm Indicators Battery Low Indicator Time Display PM Indicator W ake to Icon Sleep Mode Icon AM Indicator NOTE : AM/PM indicators will not appear when clock is set to 24 hour display mode Alarm Time Display FM Radio Indicator ...
-
iHome IP43 IP43 - page 6
4 The iP43 uses “AA” LR06 batteries (pre-installed) for backup battery system to provide continuous alarm operation and clock settings in the event of a power failure. If the Battery Low Icon located on the right of the display is flashing, it is time to replace the backup batteries. Please make sure the AC adaptor is connected, otherwise all s ...
-
iHome IP43 IP43 - page 7
5 Setting Up the iP43 Connect iP43 to Power Source Plug the AC adaptor cable into the AC Adaptor Jack and the other end into a standard 120V AC wall socket. Adaptor must be plugged in to operate unit. The iP43 does not operate on batteries (a battery back up system maintains clock settings during power failures). This unit is a preset clock: the cl ...
-
iHome IP43 IP43 - page 8
6 Using the iP43 Alarms Using the Alarms iP43 has a dual alarm system so you can set two separate alarms to differ ent alarm times, wake-to sources and fr equencies (daily , weekdays or weekend). Using the Pillow Shaker The iP43 comes with a pillow shaker that plugs into the pillow shaker jack on the back of the unit. Y ou can wake to any alarm mod ...
-
iHome IP43 IP43 - page 9
7 Using the iP43 Alarms Listening to iPhone/iPod, Radio Charging your iPhone/Pod Note: Please make sure you ar e using the correct insert for your iPhone/iPod and that it is pr operly docked into the iP43. Failure to do so may damage your iPhone/iPod. While an iPhone/iPod is docked in the unit and the unit is connected to AC power , it recharges un ...
-
iHome IP43 IP43 - page 10
8 Sleep mode, Dimmer and more Sleep Operation Sleep mode lets you sleep to your iPhone/Pod or radio, gradually lowering the volume until the unit shuts off at the selected time. 1. Press the Sleep Button to enter sleep mode. The sleep time will show in the lower display. 2. Press the Sleep Button again as needed to adjust the sleep timer from 120, ...
-
iHome IP43 IP43 - page 11
When used in the directed manner , this unit has been designed and manufactur ed to ensure your personal safety . However , improper use can result in potential electrical shock or fir e hazar ds. Please r ead all safety and operating instructions carefully before installation and use, and keep these instructions handy for futur e refer ence. T ake ...
-
iHome IP43 IP43 - page 12
iP43 does not turn on AC adaptor isn't plugged into a working wall socket or not plugged into the power supply jack on back of the unit Plug the AC adaptor into a working wall socket and plug the connector into the supply jack on the unit iP43 requir es a reset If unit is plugged in and doesn't respond, try r esetting the unit by followin ...
-
iHome IP43 IP43 - page 13
Sound is distorted V olume level is set too high Decrease the volume Sound source is distorted If you are using an external sound source like older generation of iPod or iPod Shuffle, try r educing the output volume on the device itself. Also try turning bass boost OFF . 11 Troubleshooting Solution Symptom Possible Problem Unit/adaptor gets warm af ...
-
iHome IP43 IP43 - page 14
iHome Products, a division of SDI Technologies Inc. (hereafter referred to as SDI Technologies), warrants this product to be free from defects in workmanship and materials, under normal use and conditions, for a period of 1 Year from the date of original purchase. Should this product fail to function in a satisfactory manner, it is best to first re ...
¿Tienes una pregunta acerca de iHome IP43 IP43?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con iHome IP43 IP43, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con iHome IP43 IP43 probablemente compartirá una forma de solucionarlo.