-
Hunter Fan M3559-01 - page 1
www .HunterF an.com 1.888.830.1326 30 inches 7 feet PA G E 2 What to Expect with Y our Installation Ceiling Pla te Ladder PA G E 3 T ools Needed Hanging the F an PA G E 9 Canop y T able of C ontents PA G E 8 PA G E 18 Maintenanc e, Operation & C leaning T roubleshooting ? ? ? PA G E 17 PA G E 5 T op Housing PA G E 4 Wiring Light Kit PA G E 15 P ...
-
Hunter Fan M3559-01 - page 2
www .HunterF an.com 1.888.830.1326 w .1 - T o reduce the risk of re , elec trical shock, or personal injury , mount fan directly from building structure and/or an outlet box marked acceptable for fan support of 70 lbs (31.8 kg) and use the mounting screws provided with the outlet bo x. w .2 - T o avoid possible electrical shock, befor e installi ...
-
Hunter Fan M3559-01 - page 3
www .HunterF an.com 1.888.830.1326 T ools Needed Po wer Drill (optional) 9/64” Drill Bit (optional) Ladder Screwdrivers Wire Strippers If mounting to a support structure, you will also need these tools . 3 M3559-01 • 11/12/14 • © Hunter F an Company ...
-
Hunter Fan M3559-01 - page 4
www .HunterF an.com 1.888.830.1326 4 M3559-01 • 11/12/14 • © Hunter F an Company C eiling Plate Refer to warning w .1 on pg. 2 T o av oid possible elec trical shock, before installing y our fan, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location. OFF T urn P ower Use wood scr ews ...
-
Hunter Fan M3559-01 - page 5
www .HunterF an.com 1.888.830.1326 5 M3559-01 • 11/12/14 • © Hunter F an Company T op Housing Rest the trim ring on the top housing. T rim Ring Thread the wires through the top housing . Place the canopy on the top housing. Ensur e all four screw holes line up with the screw holes in both the top housing and the adapter . Canopy Adapter Place ...
-
Hunter Fan M3559-01 - page 6
www .HunterF an.com 1.888.830.1326 Install the top housing screws. Install the grounding screw in the smaller screw hole. T hese screws can be found in the hardware bag . Grounding Screw Top Housing Screws T op Housing (continued) 8” 3/8” 8” 3/8” C U T & S T R I P (not to scale) The wires can be cut, but leave at least 8” extending fr ...
-
Hunter Fan M3559-01 - page 7
www .HunterF an.com 1.888.830.1326 Hanging the F an Raise the fan and align the slots in the canopy with the hooks on the ceiling plate . No te: Fan style may vary . Place the slots ov er the ceiling plate hooks to hang the fan. Ceiling Plate Hook Ceiling Plate Hook Note: T o hang the fan, you must tilt the canopy to an almost vertical position so ...
-
Hunter Fan M3559-01 - page 8
www .HunterF an.com 1.888.830.1326 F R O M F A N Wiring White Black (Grounded) Note: T o connect the wires , hold the bare metal leads together and place a wire connector ov er them, then twist clockwise until tight. Using the orange wire connectors from the hardware bag, connect the black wire (ungrounded) from the ceiling to the black and the blu ...
-
Hunter Fan M3559-01 - page 9
www .HunterF an.com 1.888.830.1326 9 M3559-01 • 11/12/14 • © Hunter F an Company Canop y Partially install a canopy screw , found in the hardware bag , between the ceiling plate hooks. When all the holes are properly aligned , securely tighten all three canopy screws . Canopy Screw Hold the canopy up with the screw holes aligned. P artially in ...
-
Hunter Fan M3559-01 - page 10
www .HunterF an.com 1.888.830.1326 Using both hands, push the canop y trim ring up to the top of the canopy . The canopy trim ring will snap and lock into place . Note: Should you need to r emove the trim ring, press rmly on opposite sides of the trim ring . The tabs will ex out releasing the canopy trim ring . Canopy T rim Ring Canop y (cont ...
-
Hunter Fan M3559-01 - page 11
www .HunterF an.com 1.888.830.1326 Blades Y our blades are shielded with Dust Armor® which is a nanotechnology coating that repels dust. F or cleaning the fan, use soft brushes or cloths to prevent scratching . Cleaning agents may damage the nishes. Lightly attach the blade irons to the motor with the blade iron armature screws , found in the h ...
-
Hunter Fan M3559-01 - page 12
www .HunterF an.com 1.888.830.1326 S witch Housing Remove the pr e-installed screw and red label from the switch housing . SA VE THE SCREW . Note: The screw was installed f or shipping purposes only . F eed the wire plug through the center hole of the upper switch housing , then wrap keyhole slots around the screws and twist counterclockwise. Screw ...
-
Hunter Fan M3559-01 - page 13
www .HunterF an.com 1.888.830.1326 13 M3559-01 • 11/12/14 • © Hunter F an Company S witch Housing (continued) Insert the third screw , found in the hardware bag , into place and then tighten all three (3) screws . Connect the plugs from the upper and lower switch housings . Mak e sure to line up the colored markings on the connectors. T o atta ...
-
Hunter Fan M3559-01 - page 14
www .HunterF an.com 1.888.830.1326 S witch Housing (continued) Align the keyhole slots in the lower switch housing with the stand off screws. T urn the housing counterclockwise until the standoff screws are rmly situated in the narrow end of the keyhole slots. Remove the tw o pre-installed plate screws from the switch housing . Sav e the screws ...
-
Hunter Fan M3559-01 - page 15
www .HunterF an.com 1.888.830.1326 15 M3559-01 • 11/12/14 • © Hunter F an Company Light Kit Lift the cover plate , aligning the screw holes with the screw holes in the switch housing. Install the plat e screws to secure the cov er plate to the switch housing. Align the holes in the wire basket and the hood with the holes on the rim of the uppe ...
-
Hunter Fan M3559-01 - page 16
www .HunterF an.com 1.888.830.1326 Light Kit (c ontinued) C ONGRA TULA TIONS! Y OU’RE DONE! See next page for fan opera tion instruc tions. Connect the appropriate pull chain pendant to each of the short chains coming from the switch housing . Light Pull Chain F an Pull Chain 16 M3559-01 • 11/12/14 • © Hunter F an Company ...
-
Hunter Fan M3559-01 - page 17
www .HunterF an.com 1.888.830.1326 Maintenanc e, Oper ation, & Cleaning Cleaning the fan - Use soft brushes or cloths to prevent scratching . Cleaning products may damage the nishes. T o switch the direc tion of air ow , mov e the reverse switch to the opposite position. Reverse Switch The fan pull chain controls the speed: from high to o ...
-
Hunter Fan M3559-01 - page 18
www .HunterF an.com 1.888.830.1326 T roubleshooting Lights dim when turned on or do not turn on at all. • Make sure the wattage of the light bulbs installed matches the specications on the light sockets. F an doesn’ t work • Make sure power switch is on. • Push the mot or reversing switch rmly left or right to ensure that it is engage ...
¿Tienes una pregunta acerca de Hunter Fan M3559-01?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Hunter Fan M3559-01, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Hunter Fan M3559-01 probablemente compartirá una forma de solucionarlo.