Español dropdown-ico

Manual de instrucciones Heatiator Rave4013i-c

70 de páginas 2.67 mb
Descargar

Pasar a la página of 70

Summary
  • Heatiator Rave4013i-c - page 1

    1 Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 Model: RA VE4013I-C • DO NOT store or use gasoline or other fl am- mable vapors and liquids in the vicinity of this or any other appliance. • What to do if you smell gas - DO NOT try to light any appliance. - DO NOT touch any electrical switch. DO NOT use any phone in your building. - ...

  • Heatiator Rave4013i-c - page 2

    Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 2 Listing Label Information/Location Model Name: ___________________________________________ Date purchased/installed: __________________ Serial Number: __________________________________________ Location on fi replace: _____________________ Dealership purchased from: ______________________ ...

  • Heatiator Rave4013i-c - page 3

    3 Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 Safety Alert Key: • DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury . • W ARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury . • CAUTION! Indicates a hazardous situation which, if ...

  • Heatiator Rave4013i-c - page 4

    Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 4  = Contains updated information. 13 Finishing A. Framing and Finishing Instructions . . . . . . . . . . . . . . . . . 50 B. Mantel and Wall Projections . . . . . . . . . . . . . . . . . . . . . . . 53 C. Facing Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 ...

  • Heatiator Rave4013i-c - page 5

    5 Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 B. Limited Lifetime W arranty 4021-645C 12-29-10 Page 1 of 2 Hearth & Home T echnologies Inc. LIMITED LIFETIME W ARRANTY Hearth & Home T echnologies Inc., on behalf of its hearth brands (”HHT”), extends the following warranty for HHT gas, wood, pellet, coal and electric hearth ...

  • Heatiator Rave4013i-c - page 6

    Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 6 B. Limited Lifetime W arranty (continued) 4021-645C 12-29-10 Page 2 of 2 W ARRANTY CONDITIONS:  7KLVZDUUDQWRQOFRYHUV++7DSSOLDQFHVWKDWDUHSXUFKDVHGW KURXJKDQ++7 DXWKRUL]HGGHDOHURUGLVWULEXWRU  $ OLVWRI ++7DXWKRUL]HGGHDO ...

  • Heatiator Rave4013i-c - page 7

    7 Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 C. BTU Speci fi cations MODEL: RA VE4013I-C LABORA TOR Y : Underwriters Laboratories, Inc. (UL) TYPE: V ented Gas Fireplace Heater STANDARD: ANSI Z21.88-2009/CSA 2.33-2009 V ented Gas Fireplace Heaters This product is listed to ANSI standards for “V ented Gas Fireplace Heaters” and ap ...

  • Heatiator Rave4013i-c - page 8

    Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 8 H. Requirements for the Commonwealth of Massachusetts For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for residential purposes, including those owned or operated by the Commonwealth and where the side wa ...

  • Heatiator Rave4013i-c - page 9

    9 Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 Figure 2.1 General Operating Parts B. Y our Fireplace W ARNING! DO NOT operate fi replace before read- ing and understanding operating instructions. Failure to operate fi replace according to operating instructions could cause fi re or injury . If you expect that small children or vulne ...

  • Heatiator Rave4013i-c - page 10

    Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 10 C. Clear Space W ARNING! DO NOT place combustible objects in front of the fi replace or block louvers. High temperatures may start a fi re. See Figure 2.2. Avoid placing candles and other heat-sensitive objects on mantel or hearth. Heat may damage these objects. Figure 2.2 Clear Space E ...

  • Heatiator Rave4013i-c - page 11

    11 Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 H. Lighting Instructions (IPI) The IPI system may be operated with two D-cell batteries. When using batteries, unplug the transformer . T o prolong battery life, remove them when using the transformer . 1. This appliance is equipped with an ignition device which automatically lights the b ...

  • Heatiator Rave4013i-c - page 12

    Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 12 Initial Break-in Procedure • The fireplace should be run three to four hours continuously on high. • T urn the fi replace off and allow it to completely cool. • Remove fi xed glass assembly . See Section 14.E. • Clean fi xed glass assembly . See Section 3. • Replace the fi x ...

  • Heatiator Rave4013i-c - page 13

    13 Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 Glass Cleaning Frequency: Seasonally By: Homeowner T ools Needed : Protective gloves, glass cleaner , drop cloth and a stable work surface. CAUTION! Handle fi xed glass assembly with care. Glass is breakable. • Avoid striking, scratching or slamming glass • Avoid abrasive cleaners ? ...

  • Heatiator Rave4013i-c - page 14

    Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 14 B. Maintenance T asks-Quali fi ed Service T echnician The following tasks must be performed by a quali fi ed ser- vice technician. Gasket Seal and Glass Assembly Inspection Frequency: Annually By: Quali fi ed Service T echnician T ools needed: Protective gloves, drop cloth and a stable ...

  • Heatiator Rave4013i-c - page 15

    15 Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 A. T ypical Appliance System NOTICE: Illustrations and photos re fl ect typical installations and are for design purposes only . Illustrations/diagrams are not drawn to scale. Actual product may vary from pictures in manual Figure 4.1 T ypical System 4 4 Get ting Star ted Installer Guide ...

  • Heatiator Rave4013i-c - page 16

    Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 16 B. Design and Installation Considerations Heatilator direct vent gas appliances are designed to op- erate with all combustion air siphoned from outside of the building and all exhaust gases expelled to the outside. No additional outside air source is required. Installation MUST comply wit ...

  • Heatiator Rave4013i-c - page 17

    17 Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 5 5 F raming and Clearances A. Selecting Appliance Location When selecting a location for the appliance it is important to consider the required clearances to walls (see Figure 5.1). W ARNING! Risk of Fire or Burns! Provide adequate clearance around air openings and for service access. Du ...

  • Heatiator Rave4013i-c - page 18

    Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 18 B. Constructing the Appliance Chase A chase is a vertical box-like structure built to enclose the gas appliance and/or its vent system. In cooler climates the vent should enclosed inside the chase. NOTICE: T reatment of ceiling fi restops and wall shield fi restops and construction of t ...

  • Heatiator Rave4013i-c - page 19

    19 Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 C. Clearances NOTICE: Install appliance on hard metal or wood surfaces extending full width and depth. DO NOT install directly on carpeting, vinyl, tile or any combustible material other than wood. W ARNING! Risk of Fire! Maintain speci fi ed air space clearances to appliance and vent pi ...

  • Heatiator Rave4013i-c - page 20

    Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 20 D. Mantel and W all Projections W ARNING! Risk of Fire! Comply with all minimum clear- ances to combustibles as speci fi ed. Framing or fi nishing material closer than the minimums listed must be construct- ed entirely of noncombustible materials (i.e., steel studs, concrete board, etc) ...

  • Heatiator Rave4013i-c - page 21

    21 Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 3-1/2 IN. 1 IN. AIR SP ACE NON-COMBUSTIBLE BOARD SHIPPED WITH APPLIANCE 1 IN. Figure 5.8 Non-Combustible Zone ...

  • Heatiator Rave4013i-c - page 22

    Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 22 A. V ent T ermination Minimum Clearances Roof Pitch H (Min.) Ft. Flat to 6/12...........................................................1.0* Over 6/12 to 7/12 .................................................1.25* Over 7/12 to 8/12 .................................................1.5* Ove ...

  • Heatiator Rave4013i-c - page 23

    23 Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 Figure 6.3 Minimum Clearances for T ermination O N P R Q X = AIR SUPPL Y INLET A = 12 inches................. clearances above grade, veranda, porch, deck or balcony B = 12 inches................. clearance to window or door that may be opened, or to permanently closed window C = 18 inche ...

  • Heatiator Rave4013i-c - page 24

    Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 24 A. Approved Pipe This appliance is approved for use with Hearth & Home T echnologies SLP venting systems. Refer to Section 16B for vent component information. DO NOT mix pipe, fi ttings or joining methods from differ- ent manufacturers. The pipe is tested to be run inside an enclosed ...

  • Heatiator Rave4013i-c - page 25

    25 Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 Figure 7.4 T op V ent - Horizontal T ermination V enting with 1 elbow H 1 V 1 V Minimum H 1 Maximum RA VE4013I-C 90 Elbow 1-1/2 ft. 457mm 1 ft. 305 mm 3 ft. 914 mm 2 ft. 610 mm 5 ft. 1.5 m 3 ft. 914 mm 7 ft. 2.1 m 4 ft. 1.2 m 14 ft. 4.3 m H MAX. =14 ft. (4.3 m) V + H MAX. = 40 ft. (12.2 m ...

  • Heatiator Rave4013i-c - page 26

    Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 26 INST ALLED HORIZONT ALL Y H 1 H 2 V 1 Figure 7.5 1. T op V ent - Horizontal T ermination - (continued) T op V ent - Horizontal T ermination V enting with 2 elbows Note : Use SLP Series components only . V Minimum H 1 + H 2 MAXIMUM RA VE4013I-C 90° Elbow 1 ft. 305 mm 1 ft. 305 mm 2 ft. 61 ...

  • Heatiator Rave4013i-c - page 27

    27 Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 H 2 H 1 V 2 V 1 T op V ent - Horizontal T ermination V enting with 3 elbows Note : Use SLP Series components only . 1. T op V ent - Horizontal T ermination - (continued) Figure 7.6 RA VE4013I-C V 1 Minimum H 1 + H 2 Maximum V 2 V 1 + V 2 Minimum 90° Elbow 6 ft. 1.8 m * * 1 ft. 305 mm 10 ...

  • Heatiator Rave4013i-c - page 28

    Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 28 Figure 7.7 1. T op V ent - Horizontal T ermination - (continued) T op V ent - Horizontal T ermination V enting with 3 elbows Note : Use SLP Series components only . V Minimum H 1 + H 2 + H 3 MAXIMUM RA VE4013I-C (NG ONL Y) 3 ft. 914 mm 15 ft. 4.6 m H 1 + H 2 + H 3 MAX. = 15 ft. (4.6 m) V ...

  • Heatiator Rave4013i-c - page 29

    29 Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 Figure 7.8 V ertical V ent Maximum Note: If installing a vertical vent/termination off the top of the appliance, the optional exhaust restrictor may be needed. V 1 V 1 = 44 ft. Max. (13.4 m) T op V ent - V ertical T ermination No Elbows Note : Use SLP Series components only . Exhaust rest ...

  • Heatiator Rave4013i-c - page 30

    Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 30 Figure 7.1 1 H 1 V 1 V 2 T op V ent - V ertical T ermination V enting with 2 elbows Note : Use SLP Series components only . RA VE4013I-C V 1 Minimum H Maximum V 2 V 1 + V 2 Minimum 90° Elbow 2 ft. 610 mm * * 1 ft, 152 mm 3 ft. 914 mm * * 2 ft. 457 mm 5 ft. 1.5 m * * 3 ft. 914 mm 7 ft. 2. ...

  • Heatiator Rave4013i-c - page 31

    31 Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 Figure 7.12 INST ALLED HORIZONT ALL Y H 1 H 2 V 1 V 2 T op V ent - V ertical T ermination V enting with 3 elbows Note : Use SLP Series components only . RA VE4013I-C V 1 Minimum H 1 + H 2 Maximum V 2 V 1 + V 2 Minimum 90° Elbow 1 ft. 305 mm * * 1 ft. 305 mm 2 ft. 610 mm * * 2 ft. 610 mm ...

  • Heatiator Rave4013i-c - page 32

    Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 32 T op V ent - V ertical T ermination V enting with 4 elbows Note : Use SLP Series components only . Note : There MUST be a 25% reduction in total H when using fl ex vent except when using the simple up and out installation (see Figure 5.3). V 1 MIN. H 1 MAX. V 2 MIN. H 2 MAX. V 3 MIN. 1-1 ...

  • Heatiator Rave4013i-c - page 33

    33 Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 Clearances to Combustibles: Refer to Section 5 for clearances to the appliance, man- tel, mantel legs and wall projection. Refer to Section 8 for pipe clearances to combustibles. T ermination Cap For installation of termination cap see minimum vent heights for various pitched roofs. See S ...

  • Heatiator Rave4013i-c - page 34

    Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 34 EXISTING CHIMNEY HEARTH FLOOR EXISTING CHIMNEY EXHAUST AIR VENT PIPE INLET AIR VENT PIPE T o minimize cold air drafts, seal with non-combustible insulation. TERMINA TION CAP DIRECT VENT FIREPLACE V Figure 7.16 Connecting the DV -46DV A-GCL Adapter to Appliance T op V ent • Remove top se ...

  • Heatiator Rave4013i-c - page 35

    35 Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 * When using SLP pipe, minimum clearances from the vent pipe to combustible materi- als at inside wall firestops are: T op: 2-1/2 in. (64 mm) Bottom: 1/2 in. (13 mm) Sides: 1 in. (25 mm) Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm).  SLP heat shield - designed to b ...

  • Heatiator Rave4013i-c - page 36

    Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 36 C. Install the Ceiling Firestop A ceiling fi restop MUST be used between fl oors and attics. • SLP pipe only - Frame opening 9 in. x 9 in. (229 mm x 229 mm) whenever the vent penetrates a ceiling/floor (see Figure 8.4). • Frame the area with the same sized lumber as used in ceiling/ ...

  • Heatiator Rave4013i-c - page 37

    37 Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 D. Install Attic Insulation Shield W ARNING! Fire Risk. DO NOT allow loose materials or insulation to touch vent. Hearth & Home T echnologies Inc. requires the use of an attic shield. The National Fuel Gas Code ANSI Z223.1 and NFPA 54 requires an attic shield constructed of 26 gauge m ...

  • Heatiator Rave4013i-c - page 38

    Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 38 ELBOW HEA T SHIELD SHOWN IN SHIPPING POSITION CAUTION! Risk of Cuts, Abrasions or Flying Debris. Wear protective gloves and safety glasses during instal- lation. Sheet metal edges are sharp. A. T op V ent 9 9 Appliance Preparation Figure 9.1 Elbow Shield Shown as Shipped ELBOW HEA T SHIEL ...

  • Heatiator Rave4013i-c - page 39

    39 Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 B. Securing and Leveling the Appliance W ARNING! Risk of Fire! Prevent contact with: • Sagging or loose insulation • Insulation backing or plastic • Framing and other combustible materials Block openings into the chase to prevent entry of blown- in insulation. Make sure insulation a ...

  • Heatiator Rave4013i-c - page 40

    Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 40 1 0 10 Inst alling V ent P ip e ( SLP P ipe ) Figure 10.2 High T emperature Silicone Sealant A. Assemble V ent Sections T o attach the fi rst vent component to the starting collars of the appliance: • Lock the vent components into place by sliding the pipe section onto the collar . • ...

  • Heatiator Rave4013i-c - page 41

    41 Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 C. Secure The V ent Sections • Vertical runs of pipe must be supported every 8 ft. (2.44 m). • Horizontal sections must be supported every 5 feet (1.52 m). • V ent supports or plumbers strap (spaced 120º apart) may be used to support. See fi gures 10.5 and 10.6. • W all shield ? ...

  • Heatiator Rave4013i-c - page 42

    Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 42 D. Disassemble V ent Sections • Rotate either section (see Figure 10.7) so the seams on both pipe sections are aligned as shown in Figure 10.8. • Pull carefully to separate the pieces of pipe. Figure 10.8 Align and Disassemble V ent Sections Figure 10.7 Rotate Seams for Disassembly E. ...

  • Heatiator Rave4013i-c - page 43

    43 Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 F . Install Metal Roof Flashing • See minimum vent heights for various pitched roofs (Figure 10.1 1) to determine the length of pipe to extend through the roof. • Slide the roof fl ashing over the pipe sections extending through the roof as shown in Figure 10.12. Roof Pitch H (Min.) ...

  • Heatiator Rave4013i-c - page 44

    Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 44 SCREWS CAULK STORM COLLAR (1 of 3) Figure 10.15 TERMINA TION CAP H. Install V ertical T ermination Cap • Attach the vertical termination cap by sliding the inner collar of the cap into the inner fl ue of the pipe section while placing the outer collar of the cap over the outer fl ue o ...

  • Heatiator Rave4013i-c - page 45

    45 Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 Figure 10.17 V enting through the wall Note: W hen using te rminat ion c aps wit h facto r y- supplie d heat shield attached, no additional w all shield fi restop is required on the ex terio r side of a co mbustible wall. K. Install Horizontal T ermination Cap W ARNING! Risk of Fire! The ...

  • Heatiator Rave4013i-c - page 46

    Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 46 A. Fuel Conversion • Make sure the appliance is compatible with available gas types. • Conversions must be made by a qualified service technician using Hearth & Home T echnologies speci fi ed and approved parts. B. Gas Pressure • Optimum appliance performance requires proper in ...

  • Heatiator Rave4013i-c - page 47

    47 Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 Note: Install the gas supply line in accordance with local codes, if any. If not, follow ANSI 223.1. Installation should be done by a quali fi ed installer approved and/or licensed as required by the locality. (In the Commonwealth of Massachusetts installation must be performed by a lice ...

  • Heatiator Rave4013i-c - page 48

    Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 48 A. Wiring Requirements NOTICE: This appliance must be electrically wired and grounded in accordance with local codes or , in the absence of local codes, with National Electric Code ANSI/NFP A 70-latest edition or the Canadian Electric Code CSA C22.1. • Wire the appliance junction box to ...

  • Heatiator Rave4013i-c - page 49

    49 Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 Figure 12.2 IntelliFire Pilot Ignition (IPI) Wiring Diagram with W all Switch or Thermostat E. Junction Box Installation 1. Bend junction box heat shield to the right along the perforated hand bends. 2. Remove the one screw located in front of the junction box. 3. Remove the plastic elect ...

  • Heatiator Rave4013i-c - page 50

    Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 50 1 3 13 Fi nishing A. Framing and Finishing Instructions W ARNING! Risk of Fire! Comply with all minimum clear- ances to combustibles as speci fi ed. Framing closer than the minimums listed must be constructed entirely of noncom- bustible materials (i.e., steel studs, concrete board, etc. ...

  • Heatiator Rave4013i-c - page 51

    51 Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 W ARNING! Risk of Fire! Maintain speci fi ed air space clearances to combustibles. Failure to comply with these instructions may cause a fi re or cause the appliance to overheat. F ACT OR Y -INST ALLED NON-COMBUSTIBLE BOARD LOWER COVER P ANEL = NO SCREWS ALLOWED = 1 INCH. MAX. SELF-T AP ...

  • Heatiator Rave4013i-c - page 52

    Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 52 V erify that the lower cover panel is installed correctly , and that the fi replace opening height is between 15-7/8 in. and 16-1/8 in. See Figure 13.3. Note: The lower cover panel must be pushed all the way down. The outer fi nishing fl anges should line up. The fi replace opening mu ...

  • Heatiator Rave4013i-c - page 53

    53 Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 B. Mantel and W all Projections W ARNING! Risk of Fire! Comply with all minimum clear- ances to combustibles as speci fi ed. Framing closer than the minimums listed must be constructed entirely of noncom- bustible materials (i.e., steel studs, concrete board, etc.) Failure to comply coul ...

  • Heatiator Rave4013i-c - page 54

    Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 54 C. Facing Material • Facing and/or fi nishing materials must not interfere with air fl ow through louvers, operation of louvers or doors, or access for service. • Facing and/or fi nishing materials must never overhang into the glass opening. • Observe all clearances when applying ...

  • Heatiator Rave4013i-c - page 55

    55 Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 The Deco and Illusion decorative fronts are approved for inside fi t applications. Non-combustible fi nishing materi- als up to 4 inches thick can be installed around the front (left, right, top, and bottom). For inside fi t applications, the decorative front must be in- stalled tight ...

  • Heatiator Rave4013i-c - page 56

    Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 56 D. Decorative Fronts W ARNING! Risk of Fire! A decorative front is required for this model. DO NOT operate this appliance without a decorative front in place. Only doors certi fi ed for use with this appliance model may be used. Contact your dealer for a list of doors that may be used. F ...

  • Heatiator Rave4013i-c - page 57

    57 Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 A. Remove Fixed Glass Assembly See Section 14.E. B. Remove the Shipping Materials Remove shipping materials from inside or underneath the fi rebox. The standard black rock media and manual bag assembly are also shipped underneath the fi rebox. C. Clean the Appliance Clean/vacuum any saw ...

  • Heatiator Rave4013i-c - page 58

    Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 58 Figure 14.2 Air Shutter F . Install the Mesh The mesh front is included with the Deco and Illusion fronts. 1. Remove fi xed glass assembly as instructed. 2. Place glass assembly into mesh screen such that the four mesh clips attached to the mesh assembly snap into the four corresponding ...

  • Heatiator Rave4013i-c - page 59

    59 Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 A. IntelliFire Ignition System Symptom Possible Cause Corrective Action 1. Pilot won’t light. The ignitor/module makes noise, but no spark. a. Incorrect wiring. V erify “S” wire (white) for sensor and “I” wire (orange) for ignitor are connected to correct terminals on module and ...

  • Heatiator Rave4013i-c - page 60

    Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 60 IntelliFire Ignition System - (continued) Symptom Possible Cause Corrective Action 4. Pilot lights but contin- ues to spark, and main burner will not ignite. (If the pilot continues to spark after the pilot fl ame has been lit, fl ame recti fi cation has not occurred.) a. A shorted or ...

  • Heatiator Rave4013i-c - page 61

    61 Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 1 6 16 Reference Materials A. Appliance Dimension Diagram Dimensions are actual appliance dimensions. Use for reference only. For framing dimensions and clearances refer to Section 5. G Q L H O F P N Ø I J K M S R GAS LINE ACCESS LEFT VIEW RIGHT VIEW 1 INCH ST ANDOFF ELECTRICAL ACCESS FR ...

  • Heatiator Rave4013i-c - page 62

    Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 62 8-3/4 in. 222 mm 6-1/2 in. 165 mm 6-5/8 in. 168 mm 6 in. 152 mm 6-1/2 in. 165 mm 6-5/8 in. 168 mm 9-7/8 in. 251 mm 6-1/2 in. 165 mm 9-1/4 in. 235 mm Effective Height/ Length B. V ent Components Diagrams Figure 16.2 SLP Series V ent Components 26 in. 660 mm Effective Height/Length Pipe inc ...

  • Heatiator Rave4013i-c - page 63

    63 Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 B. V ent Components Diagrams (continued) Figure 16.3 SLP Series V ent Components SLK-SNKD Snorkel T ermination Cap 13-1/2 in. 343 mm 28-1/2 in. 724 mm 10-1 1/16 in. 271mm 10-9/16 in. 269 mm 14 in. 356 mm SLP-CCS-BK Cathedral Ceiling Support Box-Black 12-1/2 in. 318 mm 8-1/16 in. 205 mm 12 ...

  • Heatiator Rave4013i-c - page 64

    Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 64 Figure 16.4 SLP Series V ent Components 13 in. (330 mm) 15 in. (381 mm) 8-1/8 in. (206 mm) 10-7/8 in. 276 mm 10-1/2 in. 267 mm 3° 87° Effective Length 5-3/4 to 8-3/8 in. 146 to 213 mm 5-1/2 in. 140 mm 8-3/8 in. 213 mm SLP-HRC-SS SLP-HRC-ZC-SS HORIZONT AL TERMINA TION CAP SLP-TRAP Horizo ...

  • Heatiator Rave4013i-c - page 65

    65 Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 Figure 16.5 V ent Components LINK-DV30B Flex Liner Kit DV -46DV A-GCL Coaxial/Colinear Appliance Connector DVP-2SL Adapter COAXIAL to COLINEAR VENTING B. V ent Components Diagrams (continued) PVI-SLP 16 IN. 406 mm 15 IN. (381 mm) 16-1 1/16 IN. (424 mm) 9-3/16 IN. (233 mm) 4-1/2 IN. 1 14 m ...

  • Heatiator Rave4013i-c - page 66

    Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 66 Cap Shield DRC-RADIUS 13-7/8 in. (352 mm) 9-1/2 in. (241 mm) 14 in. (356 mm) COOL-ADD Cap Shield 11-5/8 in. (295 mm) 5-3/4 in. (146 mm) 7-1/8 in. (181 mm) 12-1/8 in. (308 mm) DVP-BEK2 DVP-HPC Cap Brick Extension 13-7/8 in. (352 mm) 5 in. (127 mm) 11-7/8 in. (302 mm) Figure 16.6 V ent Comp ...

  • Heatiator Rave4013i-c - page 67

    67 Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 Service Parts IMPORT ANT : THIS IS DA TED INFORMA TION. When requesting service or replacement parts for your appliance please provide model number and serial number . All parts listed in this manual may be ordered from an authorized dealer . Stocked at Depot ITEM DESCRIPTION COMMENTS P A ...

  • Heatiator Rave4013i-c - page 68

    Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 68 Service Parts IMPORT ANT : THIS IS DA TED INFORMA TION. When requesting service or replacement parts for your appliance please provide model number and serial number . All parts listed in this manual may be ordered from an authorized dealer . Stocked at Depot ITEM DESCRIPTION COMMENTS P A ...

  • Heatiator Rave4013i-c - page 69

    69 Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 Service Parts RA VE4013i-C Beginning Manufacturing Date: June 2012 Ending Manufacturing Date: Active IMPORT ANT : THIS IS DA TED INFORMA TION. When requesting service or replacement parts for your appliance please provide model number and serial number . All parts listed in this manual ma ...

  • Heatiator Rave4013i-c - page 70

    Heatilator • RA VE4013I-C • 2293-900 Rev . C • 8/12 70 Heatilator , a brand of Hearth & Home T echnologies Inc. 7571 215th Street West, Lakeville, MN 55044 www .heatilator .com D. Contact Information Please contact your Heatilator dealer with any questions or concerns. For the location of your nearest Heatilator dealer , please visit www ...

Fabricante Heatiator Categoría Indoor Fireplace

Los documentos del dispositivo Heatiator Rave4013i-c que obtenemos del fabricante se pueden dividir en varios grupos. Entre ellos están::
- dibujos técnicos Heatiator
- manuales de instrucciones Rave4013i-c
- hojas de producto Heatiator
- folletos informativos
- o etiquetas energéticas Heatiator Rave4013i-c
Todos son importantes, pero lo más importante desde el punto de vista del usuario de un dispositivo lo encontraremos en el manual de instrucciones Heatiator Rave4013i-c.

Un conjunto de documentos determinado como manual de instrucciones se divide también en tipos más detallados, tales como: instrucciones de montaje Heatiator Rave4013i-c, instrucciones de servicio, instrucciones cortas o instrucciones de usuario Heatiator Rave4013i-c. Dependiendo de la situación debes buscar el documento que necesitas. En nuestra página puedes consultar el manual de instrucciones más popular del producto Heatiator Rave4013i-c.

Manuales de instrucciones parecidos

El manual de instrucciones del dispositivo Heatiator Rave4013i-c, ¿cómo debería ser?
El manual de instrucciones, también determinado como el manual de usuario o simplemente instrucciones, es un documento técnico que tiene como objetivo ayudar a los usuarios a utilizar Heatiator Rave4013i-c. Las instrucciones normalmente las realiza un escritor técnico pero en un lenguaje comprensible para todos los usuarios de Heatiator Rave4013i-c.

El manual de instrucciones completo de Heatiator debe contener unos elementos básicos. Una parte de ellos es menos importante, como por ejemplo: la portada / la página principal o las páginas de autor. Sin embargo, lo demás debe facilitarnos la información más importante desde el punto de vista del usuario.

1. Introducción y pistas sobre cómo orientarse con el manual Heatiator Rave4013i-c - Al principio de cada manual se deben encontrar las indicaciones acerca de la manera de usar un manual de instrucciones. Debe contener información sobre dónde encontrar el índice Heatiator Rave4013i-c, preguntas frecuentes o problemas más comunes – son los apartados más buscados por los usuarios de cada manual de instrucciones.
2. Índice - listados de todos los consejos acerca de Heatiator Rave4013i-c que encontraremos en el documento
3. Consejos de uso de las funciones básicas del dispositivo Heatiator Rave4013i-c - que deben facilitarnos los primeros pasos durante el uso de Heatiator Rave4013i-c
4. Troubleshooting - una secuencia sistematizada de acciones que nos ayudará a diagnosticar los problemas más importantes con Heatiator Rave4013i-c
5. FAQ - las preguntas frecuentes
6. Datos de contacto Información acerca de cómo encontrar los datos de contacto del fabricante / servicio de Heatiator Rave4013i-c en cada país si no somos capaces de solucionar el problema por nuestra cuenta.

¿Tienes una pregunta acerca de Heatiator Rave4013i-c?

Utiliza el formulario que se encuentra abajo

Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Heatiator Rave4013i-c, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Heatiator Rave4013i-c probablemente compartirá una forma de solucionarlo.

Copia el texto de la imagen

Captcha
Nueva imagen

Comentarios (0)