-
Cisco Bridge/Router 10000 Series - page 1
Corporate Headquarters: © 20 06 Cisco Syst ems, Inc. All rights reserved. Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA Upgrading to Cisco IOS Release 12.2(28)SB on a Cisco 10000 Series Router This document describes h ow to upgrade a Cisco 100 00 series rout er to Cisco IOS Release 12 .2(28)SB on an ESR-PRE2 processor . ...
-
Cisco Bridge/Router 10000 Series - page 2
2 Upgrading to Cisco IOS Release 12.2(28 )SB on a Cisco 10000 Series Router OL-8833-01 Upgrade Paths and Compatibility Upgrade Paths and Compatibility Ta b l e 1 shows the u pgrade procedure options matched to the starting ESR-PRE v ersion and Cisco I OS release. Use the information in Ta b l e 1 to determine which upgrade procedure to use. Caution ...
-
Cisco Bridge/Router 10000 Series - page 3
3 Upgrading to Cisco IOS Release 12.2(28) SB on a Cisco 10000 Series Router OL-8833-01 Upgrade Option 1: ESR-PRE1 Upgrade with Cold Start T o perform th e upgrade, foll o w these ste ps: Step 1 On the activ e ESR-PRE1, issue the write memory command to make sure the startup conf igurati on is up to date. Step 2 Copy the sa v ed startup conf igurati ...
-
Cisco Bridge/Router 10000 Series - page 4
4 Upgrading to Cisco IOS Release 12.2(28 )SB on a Cisco 10000 Series Router OL-8833-01 Upgrade Option 2: ESR-PRE2 Up grade with Cold Start Upgrade Option 2: ESR-PRE2 Upgrade with Cold Start This procedure assumes the follo wing configuration: • Cisco 10000 series chassis wit h two inst alled ESR-PRE2 processor s • A non-upgrade-enabled image su ...
-
Cisco Bridge/Router 10000 Series - page 5
5 Upgrading to Cisco IOS Release 12.2(28) SB on a Cisco 10000 Series Router OL-8833-01 Upgrade Option 3: ESR-PRE1 Upgrade with RPR Switchover At this point, the sy stem should b e operating as a dual-PRE redundan t 12.2(28)SB system in the confi gured mode (either SSO or RPR+), running the properly modif ied start up conf iguration. Y ou can verify ...
-
Cisco Bridge/Router 10000 Series - page 6
6 Upgrading to Cisco IOS Release 12.2(28 )SB on a Cisco 10000 Series Router OL-8833-01 Upgrade Option 3: ESR-PRE 1 Upgrade with RPR Switchov er T o perform the upgrade, follo w these steps: Step 1 On the activ e ESR-PRE1, issue the write memory command to make sure the startup config uration is up to date. Save the startup configuration to a TFTP s ...
-
Cisco Bridge/Router 10000 Series - page 7
7 Upgrading to Cisco IOS Release 12.2(28) SB on a Cisco 10000 Series Router OL-8833-01 Upgrade Option 3: ESR-PRE1 Upgrade with RPR Switchover • If the ESR-PRE1 conf ig-re gister is set to 0x0, it will boot to R OM monitor . Boot the ESR-PRE1 image from R OM monitor and wait for to come up as standb y in RPR mode wi th the console disabled. • If ...
-
Cisco Bridge/Router 10000 Series - page 8
8 Upgrading to Cisco IOS Release 12.2(28 )SB on a Cisco 10000 Series Router OL-8833-01 Upgrade Option 4: ESR-PRE 2 Upgrade with RPR Switchov er Step 3 Insert the second ESR-P RE1 into the empty slot. If it is not conf ig ured for autoboot, boot the correct image from the R OM monitor prompt. The second ES R-PRE1 will come up as the stand by in th e ...
-
Cisco Bridge/Router 10000 Series - page 9
9 Upgrading to Cisco IOS Release 12.2(28) SB on a Cisco 10000 Series Router OL-8833-01 Obtaining Documentation Step 7 On the acti ve ESR-PRE2 in pri vile ged EXEC mode, enter the hw-module sec-cpu r eset command to reboot the standb y ESR-PRE2. This will load the 12.2(28)SB image from bootf lash, and the standb y PRE2 will come up i n RPR mode. Not ...
-
Cisco Bridge/Router 10000 Series - page 10
10 Upgrading to Cisco IOS Release 12.2(28 )SB on a Cisco 10000 Series Router OL-8833-01 Documentation Fe edback Cisco.com Y ou can access the most current Ci sco documentation at this URL: http://www .cisco.co m/techsupport Y ou can access the Cisco website at this URL: http://www .cisco. com Y ou can access international Cis co websites at this UR ...
-
Cisco Bridge/Router 10000 Series - page 11
11 Upgrading to Cisco IOS Release 12.2(28) SB on a Cisco 10000 Series Router OL-8833-01 Cisco Product Security Overview Y o u can submit comments b y using th e response card (if present) behin d the front cov er of your document or by writ ing to the follo wing ad dress: Cisco Systems Attn: Customer Document Or dering 170 W est T asman Drive San J ...
-
Cisco Bridge/Router 10000 Series - page 12
12 Upgrading to Cisco IOS Release 12.2(28 )SB on a Cisco 10000 Series Router OL-8833-01 Obtaining Technica l Assistance at this URL: http://www .cisco.co m/en/US/products/products_ security_vulnerabilit y_polic y .html The link on this page has the curr ent PGP k ey ID in use. Obtaining Technical Assistance Cisco T echnical Support pro vides 24-hou ...
-
Cisco Bridge/Router 10000 Series - page 13
13 Upgrading to Cisco IOS Release 12.2(28) SB on a Cisco 10000 Series Router OL-8833-01 Obtaining Additional Publ ications and Information For S1 or S2 service requests or if you do not have Internet access, co ntact the Cisco T A C b y telephone. (S1 or S2 service requests are those in which you r production netw ork is do wn or se v erely de grad ...
-
Cisco Bridge/Router 10000 Series - page 14
14 Upgrading to Cisco IOS Release 12.2(28 )SB on a Cisco 10000 Series Router OL-8833-01 Obtaining Additional Pub lications and Information • iQ Magazine is the quarterly pub lication from Ci sco Systems design ed to help gro wing companies learn ho w they can use techn ology to increase re v enue, streamline their b usiness, an d expand services. ...
¿Tienes una pregunta acerca de Cisco Bridge/Router 10000 Series?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Cisco Bridge/Router 10000 Series, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Cisco Bridge/Router 10000 Series probablemente compartirá una forma de solucionarlo.