-
Packard Bell C3 - page 1
Packard Bell EasyNote C3 Disassembly Manual Packard Bell EasyNote C3 Disassembly Manual 1 ...
-
Packard Bell C3 - page 2
Packard Bell EasyNote C3 Disassembly Manual 2 Table of contents Overview .................................................................................................................................................................3 Technician Notes ................................................................................................. ...
-
Packard Bell C3 - page 3
Packard Bell EasyNote C3 Disassembly Manual 3 Overview This document contains st ep-by-step disa ssembly instruct ions for the EasyNote C3 chassis. The instructio ns are illustrated where necessa r y with images of the part that is being removed or disassembl ed. Furthermore, the screws that are removed are shown next to the image of the parts them ...
-
Packard Bell C3 - page 4
Packard Bell EasyNote C3 Disassembly Manual 4 Hazardous Voltage There is hazardous voltage present insi de the computer when it is connected to an AC supply, even when the computer’s power switch is off. Exposure to hazardous voltage could cause personal injury. To avoid risk of injury, contact an Authorized Service Provider for proper (un)instal ...
-
Packard Bell C3 - page 5
Packard Bell EasyNote C3 Disassembly Manual 5 Removing the Battery Perform the following steps to remove t he battery: 1. Make sure to power off the EasyNote C3 . 2. Turn the unit upside down. 3. Unlock the battery and slide it out of its place as the arrow shows in Fig. 1 Fig. 1 Releasing the battery Removing the Memory Modul e To remove the Memor ...
-
Packard Bell C3 - page 6
Packard Bell EasyNote C3 Disassembly Manual 6 2. Unclip the memory module as shown in Fig. 3 Fig. 3 Removing the memory module 3. Remove the memory module from its slot and put it aside. Removing the Hard Disk Drive To remove the hard disk drive, first remove the battery (see Removing the Battery ), then perform the following steps: 1. Unscrew the ...
-
Packard Bell C3 - page 7
Packard Bell EasyNote C3 Disassembly Manual 7 Fig. 5 Screws retaining the HDD assembly Removing the Keyboard To remove the Keyboard, first remove the battery (see Removing the Battery ), then perform the following steps : 1. Release the keyboard cover from the rear of the system as shown in Fig. 6 Fig. 6 Releasing the keyboard cover 2. Lift up the ...
-
Packard Bell C3 - page 8
Packard Bell EasyNote C3 Disassembly Manual 8 3. Lift up the keyboard and disconnect it fr om the system as shown in Fig. 8 Fig. 8 Disconnecting the keyboard flat cable ...
-
Packard Bell C3 - page 9
Packard Bell EasyNote C3 Disassembly Manual 9 Removing the Optical Disk Drive To remove the ODD, first remove the battery (see Removing the Battery ) and remove the keyboard (see Removing the Keyboard) then perfo rm the following steps: 1. Remove the screws retaining the opt ical disk drive as shown in Fig. 9 Fig. 9 Releasing the optical disk drive ...
-
Packard Bell C3 - page 10
Packard Bell EasyNote C3 Disassembly Manual 10 Removing the LCD Module To remove the LCD Module first remove the battery (see Removing the Battery ) and remove the keyboard (see Removing the Keyboard ), then perform the followin g steps: 1. Remove the screws retaining the He at Plate as shown in Fig. 11 Fig. 11 Removing the screws retaining the Hea ...
-
Packard Bell C3 - page 11
Packard Bell EasyNote C3 Disassembly Manual 11 4. Open up the LCD lid, release the screws and the LCD cable connector. Fig. 14 Removing the screws retain ing the LCD Cable Connector 5. Carefully lift up the LCD Module. M2.5x7 silver ...
-
Packard Bell C3 - page 12
Packard Bell EasyNote C3 Disassembly Manual 12 Removing the LCD Panel To remove the LCD panel, first remove the LCD module (see Removing the LCD Modul e ), then perform the following steps: 1. Use a pin to remove the rubber covers on the LCD module a s sho wn in Fig. 15 2. Unscrew all screws as sho wn in Fig. 15 and release carefully the LCD cover. ...
-
Packard Bell C3 - page 13
Packard Bell EasyNote C3 Disassembly Manual 13 Fig. 17 Removing the LCD Panel hinges Removing the CPU To remove the CPU first remove the battery (see Removing the Battery ) and remove the Keyboard (see Removing the Keyboard ), then perform the following step s: 1. Remove the screws retaining the He at Plate as shown in Fig. 18 Fig. 18 Removing the ...
-
Packard Bell C3 - page 14
Packard Bell EasyNote C3 Disassembly Manual 14 3. Unscrew the screws on t he CPU Heat Sink as shown in Fig. 20, and take out the CPU heat sink. F ig. 20 Removing the CPU heat sink screws Note: Beware of screws use on the CPU heat sink! Make sure to use the scre w size M2.5x7, otherwise it might cause damage to the CPU die. 4. Use a flat screw drive ...
-
Packard Bell C3 - page 15
Packard Bell EasyNote C3 Disassembly Manual 15 Note: Use extra care when unlocking or loc k ing the CP U because the scre w driver might cause damage on CPU’s edge each time when unlockin g or locking the CPU. Removing the Top Cover To remove the Top Cover , first remove the battery (see Removing the Battery ), remove the HDD (see Removing the Ha ...
-
Packard Bell C3 - page 16
Packard Bell EasyNote C3 Disassembly Manual 16 2. Release all screws on the top cover as sho wn in Fig. 23 Fig. 23 Top Cover scre ws 3. Disconnect the Touch Pad Conne ctor a s shown in Fig. 24 Fig. 24 Touch Pad connection 4. Carefully lift up the Top Cover. A=M2.5x9 silv er B=M2.5x7 silv er ...
-
Packard Bell C3 - page 17
Packard Bell EasyNote C3 Disassembly Manual 17 Removing the Touch Pad To remove the touch pad, first remove the top cover (see Removing the Top Cov er ), then perform the following steps: 1. Unscrew the screws on the Top Cove r as shown in Fig. 25 Fig. 25 Touch Pad screws 2. Carefully separate the Touch Pad module from the To p Cover. Removing the ...
-
Packard Bell C3 - page 18
Packard Bell EasyNote C3 Disassembly Manual 18 2. Unscrew all screws on the HDD hol der as shown in Fig. 27 and separate it carefully from the Main Board. Fig. 27 Screws on the HDD holder 3. Disconnect Speaker and Li d switch connectors from the Main boa rd and unscrew the screws encircled in Fig. 28 F ig. 28 Screws and connectors on Main Board M2x ...
-
Packard Bell C3 - page 19
Packard Bell EasyNote C3 Disassembly Manual 19 4. Lift up the Main Board as shown in Fig. 29 and put it aside. Fig. 29 Lifting up carefully the main board Removing the MDC Modem To remove the MDC Modem, first remov e the Main Board (see Removing the Main Board ) then perform the following steps: 1. Disconnect the MDC cable and re move the two screw ...
-
Packard Bell C3 - page 20
Packard Bell EasyNote C3 Disassembly Manual 20 Removing the Speaker Assembly To remove the Speaker Assembly, first remove the Main Board (see Removing the Main Board ) then perform the following step s: 1. Remove the screws holding the Speak e r Assembly a s shown in Fig. 31 F ig. 31 Speaker Assembly 2. Carefully remove the Speaker assem bly from t ...
-
Packard Bell C3 - page 21
Packard Bell EasyNote C3 Disassembly Manual 21 Fig. 33 Dip Switches settings Screws ...
-
Packard Bell C3 - page 22
Packard Bell EasyNote C3 Disassembly Manual 22 Notice The information in this guide is subject to change without notice. This guide contains information prote cted by copyright. No part of this guide may be photocopied or rep ro duced in any form or by any means without prior writt en consent from NEC Computers International BV. NEC COMPUTERS INTER ...
¿Tienes una pregunta acerca de Packard Bell C3?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Packard Bell C3, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Packard Bell C3 probablemente compartirá una forma de solucionarlo.