-
Harbor Freight Tools 86 - page 1
T OUCH-UP GUN Model 00086 SET UP AND OPERA TING INSTRUCTIONS Diagrams within this manual may not be drawn proportionally . Due to continuing improvements, actual product may differ slightly from the product described herein. Distributed exclusively by Harbor Freight T ools ® . 3491 Mission Oaks Blvd., Camarillo, CA 9301 1 Visit our website at: htt ...
-
Harbor Freight Tools 86 - page 2
Page 2 SKU 00086 For technical questions, please call 1-800-444-3353. SA VE THIS MANUAL Y ou will need this manual for the safety instructions, assembly and operating instructions and parts list. Put it in a safe, dry place for future reference. Keep your invoice with this manual. Write the invoice number on the inside front cover . SPECIFICA TIONS ...
-
Harbor Freight Tools 86 - page 3
Page 3 SKU 00086 For technical questions, please call 1-800-444-3353. 1 1. ST A Y ALERT . W atch what you are doing. Use common sense. Do not operate any tool when you are tired. 12. CHECK DAMAGED P ARTS. Before using any tool, any part that is damaged should be carefully checked to determine that it will operate properly and perform its intended f ...
-
Harbor Freight Tools 86 - page 4
Page 4 SKU 00086 For technical questions, please call 1-800-444-3353. ASSEMBL Y Connect the Spray Unit to the Canister Unit as shown in Figure 1. BEFORE YOU USE YOUR TOUCH-UP GUN A coupler is required to connect the T ouch-Up Gun to an air compressor . Select the coupler , e.g. ¼” “M” style NPT , etc. that mates with the end of the air hose ...
-
Harbor Freight Tools 86 - page 5
Page 5 SKU 00086 For technical questions, please call 1-800-444-3353. OPERA TION Setup Refer to Figure 3 for the location of parts called out in this section. Figure 3 -- Operation Diagram Step 1. Move the LEVER (#29) counterclockwise until the YOKE (#30) is free from the CUP LOCKS (#35). Step 2. Lift and remove the Paint Gun from the CUP (#34). St ...
-
Harbor Freight Tools 86 - page 6
Page 6 SKU 00086 For technical questions, please call 1-800-444-3353. The fan size is adjusted by turning the F AN ADJUSTING SCREW (#28) clockwise for a narrow spray and counterclockwise for a wider spray . Adjusting Jet Shape The Jet Shape is adjusted by turning the AIR CAP (#1). It should be perpendicular to the ground to create a horizontal jet ...
-
Harbor Freight Tools 86 - page 7
Page 7 SKU 00086 For technical questions, please call 1-800-444-3353. SPRA YING TECHNIQUES Y our T ouch-Up Gun is designed for light touch-up work, stenciling, and small job duties. For heavy or medium production work, we suggest our H.V .L.P . and professional model spray guns. For most uses, e.g. painting walls, benches, vehicles, etc., the best ...
-
Harbor Freight Tools 86 - page 8
Page 8 SKU 00086 For technical questions, please call 1-800-444-3353. MAINTENANCE General Maintenance Checking & Replacing the Needle Needle wear is expexcted and inspection during Cleaning will ensure the continued top- performance of your T ouch-Up Gun. If needle tip wear is noted: Step 1. Unscrew the F AN ADJUSTING SCREW (#28) and rem ...
-
Harbor Freight Tools 86 - page 9
Page 9 SKU 00086 For technical questions, please call 1-800-444-3353. Cleaning: Step 1. Depressurize the cup and disconnect the air hose. Step 2. Remove the Paint Gun from the CUP as described in OPERA TION . Step 3. Empty the paint or coating from the CUP . Dispose of properly . Step 4. Pour a small amount of clean solvent (as specied by the pa ...
-
Harbor Freight Tools 86 - page 10
Page 10 SKU 00086 For technical questions, please call 1-800-444-3353. Lubrication: Before and after each use of the T OUCH-UP GUN, perform the following lubrication process, using a non-silicon, spray gun lubricant: Step 1. Put two or three drops of lubricant on the NEEDLE (#24), in front of the TRIGGER (#14). T ip the gun backward and allow the l ...
-
Harbor Freight Tools 86 - page 11
Page 1 1 SKU 00086 For technical questions, please call 1-800-444-3353. Preventative Maintenance Periodically check the following: Needle Wear: Visually inspect NEEDLE (#24) tip for wear . NEEDLE wear will cause the paint pattern to be uneven. If NEEDLE wear is noted, replace the NEEDLE per GENERAL MAINTENANCE, CHECKING AND REPLACING THE NEEDLE. Cu ...
-
Harbor Freight Tools 86 - page 12
Page 12 SKU 00086 For technical questions, please call 1-800-444-3353. P ARTS LIST P ART # DESCRIPTION QTY P ART # DESCRIPTION QTY 1 Air Cap 1 23 Union 1 2 Inner Ring 1 24 Needle 1 3 Retainer Ring 1 25 Lock Nut 1 4 Fluid Nozzle 1 26 Rear Nut 1 9 Ring 1 27 Spring 1 10 Packing 1 28 Fan Adjusting Screw 1 11 V ol. Adj. Screw Receiver 1 29 Lever 1 12 V ...
-
Harbor Freight Tools 86 - page 13
Page 13 SKU 00086 For technical questions, please call 1-800-444-3353. LIMITED 1 YEAR W ARRANTY Harbor Freight T ools Co. makes every ef fort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of one year fr ...
¿Tienes una pregunta acerca de Harbor Freight Tools 86?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Harbor Freight Tools 86, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Harbor Freight Tools 86 probablemente compartirá una forma de solucionarlo.