-
Philips 10 - page 1
Philips Hospit ality TV Installation Manual for 22HFL3233D/10 26HFL3233D/10 32HFL3233D/10 42HFL3233D/10 Version 1.0 ...
-
Philips 10 - page 2
1 Contents 1. Requirements befor e starting the installation .......................................................................................................... 2 2. Find out the state of the TV ...................................................................................................................................... 3 3. Re -inst ...
-
Philips 10 - page 3
2 1. Requirements bef ore starting the i nstallation Before starting the in stallation, make sure that you ha ve everything you need at han d. Master remote control 22AV8573 or Guest remote control 22AV1104B And USB stick You will need the master remote c ontrol or the gu est remote contr ol to access th e menus. To access the setup menu press the ...
-
Philips 10 - page 4
3 2. Find out the state of the TV It is important to kn ow if a TV is in ‘virg in mode’ (out of the box) or ins talled before. If you can see this screen below, y ou know that the TV is in ‘virgin mode’ and you can install the se t. See chapter 4 of this manual. If you power on the set and then press the ‘H ome’ button on th e guest rem ...
-
Philips 10 - page 5
4 3. Re -install TV If you want to start an in stallation from s cratch you can always re-install the TV. This can be d one by using the option: Re-install TV set. If PBS is active you can access the setup m enu press the ‘RC5 SETUP’ key, and then press the ‘Home/Menu ’ button (For the guest re mote control, press the following keys in sequ ...
-
Philips 10 - page 6
5 Navigate to “Rein stall TV” Press “OK” to r einstall TV set. If all is correct select “YES” and press “OK”. After this operation the TV will power off and on and display the installation wizard. Note: All settings are at default values and no channel plan is available. After reinstalling, the PBS Setup menu will keep the PBS Mode, ...
-
Philips 10 - page 7
6 4. Installation wizard . When you turn on th e TV for the first ti me, or you hav e reinstalled the TV, you should see the following scre en. Here you will need to sel ect your preferred language . After this, you will need to select the country. Depend ing on the countr y selection, some pre-defined settin gs will be activated. Note: If you are ...
-
Philips 10 - page 8
7 The next step is to choose betwe en ‘Shop’ and Home’ use. If you select “ SHOP ” an ‘e - sticker’ ban ner will be displa yed on the TV. This is f or commercial purp ose only. Now you can select the visual and hearing impaired options. If you select ‘ O n’ , your TV will aut omatically tu rn on settings to help visual and hearin ...
-
Philips 10 - page 9
8 For the channel installa tions, select ‘Ins tall TV channels’ and press ‘OK’ Then you can selec t ‘Continue’ and press ‘ OK’ again. Here you can sel ect the type of channels you w ould like to insta ll. 1. Antenna (DVB-T) + analog ue channels 2. Cable (DVB-C)+ analog ue channels Note: The installation wizard is identical for DVB-T ...
-
Philips 10 - page 10
9 It is advisable to ch eck the settings befor e starting the search. The first option in th e setting s page is the “ Frequency scan ” . This has 2 options : - “ Quick ” : this i s a fast method t o search channels but it might skip s ome channels (dependin g on the network). - “ Full ” : the scan will search on all frequencies and wil ...
-
Philips 10 - page 11
10 The last option is “ R eset ” a nd this will reset the search settings to default. After y ou have checked or changed settings, you can s elect “ Done ” and sel ect “ Start ” t o start the channel s earch. During the channel search you can see the progress b ar and how man y channels are found a t that time. When the search is done, ...
-
Philips 10 - page 12
11 A wizard will start to guide you throug h the process of setting the soun d and picture on the TV set. Select “ Continue ” to start t he wizard and press “ OK ” on remot e control. The wizard will ask you some questi ons about which image you prefer, select th e option you d esire and press “ OK ” on the remo te control. Once this wi ...
-
Philips 10 - page 13
12 5. Channel options a. Reordering channel s Check if PBS Menu is active. Press “ Home ” button to se e the guest menu. If the menu is displa yed with “ Add new device ” and “ Help ” , the PBS Menu i s not active. If the menu is displa yed without “ Add new device ” an d “ Help ” , the PBS Menu is active and TV menu has restric ...
-
Philips 10 - page 14
13 The PBS menu will appear like in pictur e. Using the arrow keys you can navigat e through this MEN U. To disable PBS mode use arrow keys to selec t the “ OFF ” option an d confirm with “ OK” . The previous menu will be active, use left arr ow to go the base m e nu of the PBS menu. Go to “ Store ” o ption down the bottom of the menu a ...
-
Philips 10 - page 15
14 When you press “OK” the next image will appear and you will ha ve to confirm. After the confirma tion the TV will r estart. After po wer on all PBS settings will be disabled. This menu will all ow you to set up channels, reinstall c hannels, change pictur e setting s, add new devices. A s you can see in the picture y ou have two ne w section ...
-
Philips 10 - page 16
15 Select “Reorder” and Press “OK” button on th e remote control to re order channels. N avigate to the channel that you wan t to move and Press “OK” on the remote con trol to select that channel . The arrows around the channel indicate that the channel is selected and can be moved. Use arrow keys to m ove the channel to the new p ositi ...
-
Philips 10 - page 17
16 When you are finished with the re- ordering pre ss “ Options ” on the r emote control again. Press “OK” on the r emote control to confirm that you are don e with the re-orderi ng. b. Rename channels Select the channel, press the “Options” button on the remote control and select “Rename” to change name of a channel. If you then pr ...
-
Philips 10 - page 18
17 6. PBS Mode [Off]: The TV operat es as a basic (consum er) TV. [On]: All settings in the P BS mode Setup menu are active. Only by sw itching on this mode the TV acts as a Hospitality TV . Sets the room I D. Room ID can be used t o distinguish between different floors/rooms/setup s when using SmartInstall. A shortcut to en ter the consumer ins ta ...
-
Philips 10 - page 19
18 When the TV is switche d on it will start up on the specified source/channel . Available EXT1, EX T2, V GA, HDMI, H DMI side, AV side or one of the installed TV ch annels. When the TV is switche d on it will start up on the specified volume level. Selectable value fro m 00 until 60. This specifies the maximum allowable volume level of the TV. Se ...
-
Philips 10 - page 20
19 [On] To enable the welcome message. [Off] No welco me message Line 1: First line of welcome message. Line 2: Second line of welcome mes sage. Clear: Will del ete the messag e enter on welco me message. When pressing “OK” button on remote control while editing line 1 or 2, a vi rtual keyboard will pop up on screen. Maximum 20 charact ers per ...
-
Philips 10 - page 21
20 [Off]: TV responds to commands guest re mote contr ol. [On]: TV does not respond to comman ds guest remote control. Master remote co ntrol 22AV8573 (yellow) or RC2573 (green) commands are not affec ted by this setting . [Off]: On Screen Displ ay suppressed. [On]: On Screen Displa y not suppressed. [Off]: PBS setup menu can be accessed by both Gu ...
-
Philips 10 - page 22
21 [Off]: Disables telet ext. [On]: Enables telet ext. [Off]: Disables MH EG. [On]: Enables MHEG. [Off]: Disables EPG. [On]: Enables EPG. [Off]: Closes subtitl es. [On]: Displays subtitle s. [On during mute]: Displays subtitles when au dio is muted. [Off]: Disables USB multimedia function. [On]: Enables USB multi media functions. Feature is not inf ...
-
Philips 10 - page 23
22 Defines the tim e interval between nu meric button s when users press digits on the remote contr ol. Selectable values f rom 0.5 to 9.9 secon ds. Allows the installer to define which external sources to be displayed on the source lis t when pressing AV button on the Guest remote control. Only the sources marked [X] appear in the source list. To ...
-
Philips 10 - page 24
23 [Off]: The volume +/ - on the Guest remote control will affect both the TV Main spe aker and the headp hone volume. [On]: The volume +/ - o n the Guest remote control will affect both the TV Main spe aker and the headp hone volume. After pressin g “ MUT E ”, th e volume +/ - on the Guest remote control will not reactivate the TV Main speaker ...
-
Philips 10 - page 25
24 To set the color of the TV in multi remot e. Guest remote control sup ports up to four televisions operating in one room without interferenc e from each other’s remote cont rols. Each TV and a Guest remote control can be set to match . Selectable values: Blue, Green, Yello w, Red. [Off]: Disables MyCh oice function. [On]: Enables MyCh oice fun ...
-
Philips 10 - page 26
25 This will store all s ettings and restart TV to apply all ch anges. After storing PBS settings, t he TV will restart to ap ply the new param eters. Now you can cl one all settings t o other TV sets by using the option TV to USB and USB to TV. Check how to clone settin gs . ...
-
Philips 10 - page 27
26 7. Welcome Log o Startup time takes up approximatel y 7 seconds File format: 12 80 x 720 / PN G / NO layers / 256 c olors Note: below ti ming values are approximate indica tions and can differ fr om real si tuation! How to upload Welcome Logo 1. Create graphics file : 1280 x 720 / PNG / NO la yers / 25 6 colors . 2. File name: TP M63HE_WelcomeL ...
-
Philips 10 - page 28
27 8. Cloning On the USB which is containing the software upgrad e you can clone th e settings. The instant initial cl oning will first upgrade de softwar e version and after will clone the setting s from USB key. Folders generate by TV on USB ke y are: – TPM61HE (42HFL3 233) – TPM64HE (32HFL3 233) – TPM63HE (22/ 26HFL3233) Cloning 22 and 26 ...
-
Philips 10 - page 29
28 11. CSM (Consumer Se tup menu) The CSM contains data about the TV softwar e, serial nu mber and other details. T he menu can be access ed using a standard remote c ontrol or using the master remote c ontrol. 1. Using the standard remote contr ol: press the f ollowing key sequence “1 ,2,3,6,5, 4” 2. Using master re mote con trol (22AV8753D) : ...
¿Tienes una pregunta acerca de Philips 10?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Philips 10, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Philips 10 probablemente compartirá una forma de solucionarlo.