-
Wyse Technology X90 - page 1
Installation Guide Wyse ® X90 and X90e Mobile Thin Clients Flash and Memory Upgrade Kit Issue: 042810 PN: 883884-21L Rev . A ...
-
Wyse Technology X90 - page 2
ii Copyright Notice © 2010, Wyse T echnology Inc. All rights reserved. This manual and the software and firmware described in it ar e copyrighted. Y o u may not reproduce, transmit, transcribe, store in a retrieval system, or tr anslate into any language or computer language, in any form or by any means, electronic, mechanical, magnet ic, optica l ...
-
Wyse Technology X90 - page 3
iii Regulatory Compliance for Wyse Pr oducts Basic EMC and Safety Requirements Wyse appliances are compliant with the regulatory requirements in the regio ns listed below . U.S.A. - FCC Part 15 (class B) Canada - CAN/CSA-C22 No. 60950 Europe - EN 55022 (class B), EN 61000-3-2 (class A), EN 6100 0-3-3, EN 90650-1:2000+ALL Canadian DOC Notices Class ...
-
Wyse Technology X90 - page 4
iv This page intentionally blank. ...
-
Wyse Technology X90 - page 5
Contents About this Guide 1 Finding the Information Y o u Need in this Guide 1 Wyse T echnical Support 1 Wyse Online Community 1 Related Online Resources Available at Wyse 1 Getting Started 2 Kit W arranty 2 Kit Contents 2 Required T ools and Materials 3 Installing the Upgrade Kit 4 V erifying the Mobile Thin Client’ s Operation 7 Attaching the U ...
-
Wyse Technology X90 - page 6
vi Contents This page intentionally blank. ...
-
Wyse Technology X90 - page 7
Wy s e ® X90 and X90e Mobile Thin Clients Flash and Memory (RAM) Upgrade Kit Installation Guide About this Guide This guide describes how to install the 1-GB or 2 -GB flash an d 2-GB RAM Upgrade Kit in a Wyse X class mobile thin client. The information in this document is inten ded for users of the following mobile th in client products: •X 9 0 ...
-
Wyse Technology X90 - page 8
2 If you need to upgrade your operatin g system, contact Wyse Customer Support at: http://www .wyse.com/s upport . Wyse Thin Computing Softwa re is available on the Wyse W eb site at: http://www .wyse.c om/products/software . Getting Started This section provides information abo ut your flash and RAM kit warran ty , kit contents, and required tools ...
-
Wyse Technology X90 - page 9
3 Figure 3 Upgrade Serial Label Required T ools and Materials Y ou will need the following recommen ded tools to install the kit: • Small Phillips screwdriver • Plastic alignment tools or equivalent Figure 4 Recommended tools Wa r n i n g Flash and RAM modules may be su scepti ble to damage by Electro-Static Discharge (ESD). All industry-s tand ...
-
Wyse Technology X90 - page 10
4 Installing the Upgrade Kit T o install the 1-GB or 2-GB flash and 1-GB RAM Upgrade Kit in an X90 or X90e mobile thin client: Caution Follow all precautions list ed in the Quick-Start Guid e that came with your mobile thin client for di sconn ectin g and reconnectin g the mobile thin client. 1. Perform a proper shutdown of the mobil e thin clie nt ...
-
Wyse Technology X90 - page 11
5 5. T o remove the existing flash module, depend ing on the type of module you have, you must either pull up the m odule in the dir ection as shown in Figu re 7 , or remove the tw o screws as shown in Figure 8 . Rock the module carefully until free of the connector . Wa r n i n g Flash and RAM modules may be su scepti ble to damage by Electro-Stat ...
-
Wyse Technology X90 - page 12
6 7. T o remove the existing RAM module, use your fingers to unlock the two locking clamps at either side of the module by pushing the cl amps in the dire ction of the arrow s shown, see Figure 9 . The module should pop up from its so cket. Lift out the RAM module. Figure 9 Removing the RAM module 8. Insert the new RAM module into the connecto r of ...
-
Wyse Technology X90 - page 13
7 V erifying the Mobile Th in Client’ s Operation T o verify that th e mobile thin client works properly: 1. Reconnect the power cord and p ower adapter , and then press the power button on the mobile thin client to ap ply power . 2. After the mobile thin client restarts, close three windows that have opened on the screen by following these instr ...
-
Wyse Technology X90 - page 14
8 c. Click Shutdown in the XPE TEST window to shutdown the mob ile thin client, see Figure 12 . Figure 12 Shutting down from the XPE TEST window 3. Press the power button on the mobile thin client for it to restart. 4. From the desktop, click Start | About to open the Client In formation window , see Figures 13 . ...
-
Wyse Technology X90 - page 15
9 Figure 13 Client Information 5. V erify that the MAC address and Serial Number matches the serial number and MAC address on the thin client. 6. V erify that the RAM Configuration is approximately 1984 MB . 7. V erify that the Flash Configurat ion is less than 1024 MB for a 1-GB flash upgrade and less than 2048 MB for a 2-GB flash up gr ade. 8. Cl ...
-
Wyse Technology X90 - page 16
10 Attaching the Upgrade Serial Label The Wyse conver sion kit is supplied with a se rial label that must be attached to each mobile thin client. At tach the label as shown in Figure 14. Sufficient labels mu st be purchased for mobile th in clients to be upg raded. Caution Failure to install the label may cause the mobile thin c lient to receive in ...
-
Wyse Technology X90 - page 17
11 Figures 1 Flash module types 2 2 RAM module types 2 3 Upgrade Serial La bel 3 4 Recommended tool s 3 5 Removing b ottom screws from acces s cover 4 6 Lifting off the access cover 4 7 Removing an olde r-type flash module 5 8 Removing screws from newer-typ e flash module 5 9 Removing the RAM module 6 10 Closing the WinPing window 7 1 1 Closing the ...
-
Wyse Technology X90 - page 18
Installation Guide Wyse® X90 and X90e Mobile Thin Clients Flash and Memory Upgrade Kit Issue: 0428 1 0 Written and publishe d by: Wyse T echnology Inc., April, 2010 Created using Fra m eM a ke r ® and Acrobat ® ...
¿Tienes una pregunta acerca de Wyse Technology X90?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Wyse Technology X90, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Wyse Technology X90 probablemente compartirá una forma de solucionarlo.