-
Harbor Freight Tools 91377 - page 1
7,500 W A TT PEAK, 6,600 W A TT RA TED GENERA T OR WITH ROBIN ® ENGINE ASSEMBL Y AND OPERA TING INSTRUCTIONS Distributed exclusively by Harbor Freight T ools. 3491 MISSION OAKS BL VD., CAMARILLO, CA 9301 1 VISIT OUR WEB SITE A T HTTP://WWW .HARBORFREIGHT .COM Copyr ight © 2004 by Harbor Freig ht T ools ® . All right s reserved. No portion of thi ...
-
Harbor Freight Tools 91377 - page 2
SKU 91377 For technical questions, please call 1-800-444-3353. Page 2 SPECIFICA TIONS Generator W attage @ 240V : 6,600 (rated), 7,500 (peak) W attage @ 125V : 6,000 (rated), Alternator: single phase, 6 KV A. V oltage: 240 / 125 V AC, 60Hz; Nominal current: 50 amps at 125 V AC, 25 amps at 240 V AC; Outlets: 120 V AC Standard, 120 V AC twist-lock 3- ...
-
Harbor Freight Tools 91377 - page 3
SKU 91377 For technical questions, please call 1-800-444-3353. Page 3 Read all instructions before installing or using this generator! Ensure installation meets all applicable safety , and local and national electrical codes. Have installation performed by a qualied, licensed electrician and building contractor . Do not operate the generator wit ...
-
Harbor Freight Tools 91377 - page 4
SKU 91377 For technical questions, please call 1-800-444-3353. Page 4 Handling and Installation Precautions 1. All electrical work, including earth-ground connection, should be completed by a licensed electrician. 2. Any separate fuel storage generator supply facility , must be built or installed in full compliance with relevant local, state, and f ...
-
Harbor Freight Tools 91377 - page 5
SKU 91377 For technical questions, please call 1-800-444-3353. Page 5 8. Do not rell the generator fuel tank of the bed frame while the engine is running. 9. Do not operate the generator with known leaks in the fuel system. 10. Use only engine manufacturer recommended fuel and oil uids. Mechanical Precautions 1. The generator is designed with ...
-
Harbor Freight Tools 91377 - page 6
SKU 91377 For technical questions, please call 1-800-444-3353. Page 6 8. Keep all electrical equipment clean and dry . Replace any wiring where the insulation is cracked, cut, abraded or otherwise degraded. Replace terminals that are worn, discolored, or corroded. Keep terminals clean and tight. 9. Insulate all connections and disconnected wires. 1 ...
-
Harbor Freight Tools 91377 - page 7
SKU 91377 For technical questions, please call 1-800-444-3353. Page 7 12. Only use 3-prong (125 V AC) or 4-prong (240 V AC), grounded extension cords. W arning: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur . It must be understood by the operator that ...
-
Harbor Freight Tools 91377 - page 8
SKU 91377 For technical questions, please call 1-800-444-3353. Page 8 should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away from the user , reducing the risk of electric shock. (See Figure A.) 2. The grounding prong in the plug is connected through the green wire inside the cord to the gro ...
-
Harbor Freight Tools 91377 - page 9
SKU 91377 For technical questions, please call 1-800-444-3353. Page 9 6. If you are using an extension cord outdoors, make sure it is marked with the sufx “W- A” (“W” in Canada) to indicate it is acceptable for outdoor use. 7. Make sure your extension cord is properly wired and in good electrical condition. Always replace a damaged exten ...
-
Harbor Freight Tools 91377 - page 10
SKU 91377 For technical questions, please call 1-800-444-3353. Page 10 UNP ACKING When unpacking, check to make sure that all the parts are included. Refer to the Assembly section, and the Assembly Drawing and Parts List at the end of this manual. If any parts are missing or broken, please call Harbor Freight T ools at the number on the cover of th ...
-
Harbor Freight Tools 91377 - page 11
SKU 91377 For technical questions, please call 1-800-444-3353. Page 1 1 Generator Setup and Cable Connections 1. Place the Generator outdoors where it will be used. This should be on a at surface and away from ammable materials. Do not allow the Generator to get wet. If used indoors, the area must be well ventilated to allow dissipation of ex ...
-
Harbor Freight Tools 91377 - page 12
SKU 91377 For technical questions, please call 1-800-444-3353. Page 12 INSPECTION, MAINTENANCE, AND CLEANING Disconnect the wire to the Spark Plug of the Engine before performing any inspection, maintenance, or cleaning procedures. 1. Before each use, inspect the general condition of the Generator . Check for loose screws, misalignment or binding o ...
-
Harbor Freight Tools 91377 - page 13
SKU 91377 For technical questions, please call 1-800-444-3353. Page 13 NOTE : Some part s are liste d and show n for illus trati on purpo ses onl y and are not available individually as replacement parts. P ARTS LIST Part Code # Description Qty . 1 EH410GE GA ENGINE, 13.5 HP , ROBIN 1 2 31227 SINGLE PHASE AL TERNA TOR, 6 KV A 1 3 30010102 MOUNTING ...
-
Harbor Freight Tools 91377 - page 14
SKU 91377 For technical questions, please call 1-800-444-3353. Page 14 ASSEMBL Y DRA WING PLEASE READ THE FOLLOWING CAREFULL Y THE MANUF ACTURER AND/OR DISTRIBUT OR HAS PROVIDED THE P ARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONL Y . NEITHER THE MANUF ACTURER NOR DISTRIBUTOR MAKES ANY REPRESENT A TION OR W ARRANTY OF ANY KIND T O THE BUYER TH ...
-
Harbor Freight Tools 91377 - page 15
SKU 91377 For technical questions, please call 1-800-444-3353. Page 15 WIRING DIAGRAM Note: Only a licensed electrician should perform electrical repairs on this generator . Green Black White Black ...
-
Harbor Freight Tools 91377 - page 16
SKU 91377 For technical questions, please call 1-800-444-3353. Page 16 SCHEMA TIC DRA WING RE-ST ARTER SWITCH WITH GFCI A B D 7 5 E 6 D 9 4 3 F 1 2 12 B G C 1 1 10 Red Black Blue White Black Black Black Black White White Green Green Black ASSEMBL Y OF CABLE & TERMINALS ITEM QTY DESCRIPTION A 1 Inlet 20A B 1 Inlet 30A 125/250V C 1 Inlet 30A 129 ...
¿Tienes una pregunta acerca de Harbor Freight Tools 91377?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Harbor Freight Tools 91377, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Harbor Freight Tools 91377 probablemente compartirá una forma de solucionarlo.