-
Perle Systems S-10G-STS - page 1
P/N 5500325-10 Perle 10G Media Con verters Installation Gui de S-10G-STS S-10G-XTS S-10G-XTX S-10G-XTS H S-10G-XTX H ...
-
Perle Systems S-10G-STS - page 2
Perle S- 10G Media Converter Installation Gu ide 2 Over v iew This docum ent contains ins tructions neces sary for the ins tallation and operatio n of the Perle S-10G Standalon e Media Converter s. The Perle S-1 0G Standalone M edia Converters are 10 Gig abit Media Con verters with two pluggable transc eiver ports. T he S-10G supports lo w power tr ...
-
Perle Systems S-10G-STS - page 3
Perle S- 10G Media Converter Installation Gu ide 3 Front and Rear Panel Components Front View Rear View ...
-
Perle Systems S-10G-STS - page 4
P/N 5500325-10 Inst allation The default s witch setting ( all switches in the U P position) will work for m ost installations. Thes e are the steps r equired to conf igure the Perle S-1 0G standalon e media converter: 1. Set the DIP s witch settings .(optional) 2. Connect the grounding lug. (optional) 3. Connect the power cord str ain relief clip. ...
-
Perle Systems S-10G-STS - page 5
Perle S- 10G Media Converter Installation Gu ide 5 S-10G-XTS, S-10G-XTSH S-10G-XTX, S-10G-XTXH DIP Switch Settings The DIP s witches are acc essible through the o pening in the s ide of the enc losure. The functi on of the DIP switches varies b y model, so pl ease refer to th e appropriate m odel. Note: Switc h changes m ade when the produc t is po ...
-
Perle Systems S-10G-STS - page 6
Perle S- 10G Media Converter Installation Gu ide 6 Operating Mode (Switch 1) Switch Posit ion Mode Up (defau lt) Data Down Test Data: In Data m ode, data will flow between the two fiber connections. Test: T est Mode is used to run diagnostics, e nable loopback and for running the Built In Link Tests. Note: The Oper ation Mode ( Switch 1) affects th ...
-
Perle Systems S-10G-STS - page 7
Perle S- 10G Media Converter Installation Gu ide 7 Test Function (Sw itch 2 – Test Mode) Switch Posit ion Type Up (defau lt) Built In Link Test Down Loopback Built In Link T est: Switch 2 causes the S-1 0G to initiate the Built In Link T ests on the specifi ed port. Switch 3 determines the specified por t for the Built I n Link Tests . If Switch ...
-
Perle Systems S-10G-STS - page 8
Perle S- 10G Media Converter Installation Gu ide 8 Note : If th e remote media converter is not a Perle S-10G then th e remote media c onverter will need to be put int o loopback mod e. See the docum entation that ca me with that me dia converter. Sequence of E vents 1. The Local S-10G sends the Remote S-10G a signal to go i nto loopback mode. 2. T ...
-
Perle Systems S-10G-STS - page 9
Perle S- 10G Media Converter Installation Gu ide 9 Illustration of the FFA feature Media Converter A Configuration Link Mod e–Standard Mode Fiber Fault Alert Media Converter B Configuration Link Mod e–Smart Link Pass th rough Mode Fiber Fault Alert Sequence of Events 1. Media Con verter A loses fi ber connection (RX ). 2. Media Con verter A not ...
-
Perle Systems S-10G-STS - page 10
Perle S- 10G Media Converter Installation Gu ide 10 Operation Powering up the Perl e Media Converter 1. Connect the Perle supplied power adapter t o the media converter. 2. Turn on the power at the so urce. 3. Check that the PWR LED light is lit. Status LED The Perle 10G Media conv erters have three stat us LEDs located on the front pa nel of the u ...
-
Perle Systems S-10G-STS - page 11
Perle S- 10G Media Converter Installation Gu ide 11 LK1- Port 1 A ctivity On: Fiber l ink present. Blinking quic kly : Fiber link present and receivin g data. Blinking slowl y : The fiber link has been tak en down as a result of Smart Link Pass-Through. Blinking one second on, 3 se conds off: the m aximum specified operating tem perature with in th ...
-
Perle Systems S-10G-STS - page 12
Perle S- 10G Media Converter Installation Gu ide 12 • Cross-head s crewdriver (n ot provided) Note : For your safety, when inst alling this equi pment, always ensure that t he chassis gro und connection is installed first and disconnected last. Attaching the Groundi ng Lug 1. Attach the gr ounding lug to one end of an 18- 12 A W G wire. 2. Attach ...
-
Perle Systems S-10G-STS - page 13
P/N 5500325-10 T roublesh ooting General Ensure po wer is supplied to the media converter – use of the Perle supp lied power a dapter is highl y recomm end ed. Ensure that the SFP+ or X FP modules are of the same speed and ar e operating pr operly. Ensure both devices on eit her end of each fib er are compatible. For fiber conn ec ...
-
Perle Systems S-10G-STS - page 14
Perle S- 10G Media Converter Installation Gu ide 14 Module Tempe rature Protection Every S-10G c omes equipp ed with an inter nal fan to provide cooling to th e unit. Howeve r, if any of the m odules are operating above the ir specified m aximum operating t emperature, th e S-10G will reduce th e power to th ese m odules. The S-10G will continue to ...
-
Perle Systems S-10G-STS - page 15
Perle S- 10G Media Converter Installation Gu ide 15 Technical Specifications The f ollowing applies to all Perle Standal one S-10G Medi a converters . Power Input/C onsumption 9-30VDC STS 1.0A Max, 600m A at 12VD C XTS 1.2A Max, 800m A at 12VD C XTX 1.5A Max, 1.0 A at 12VDC XTSH 1.5A Max, 1.0 A at 12VDC XTXH 2.0A Max, 1.4 A at 12VDC Operating T emp ...
-
Perle Systems S-10G-STS - page 16
Perle S- 10G Media Converter Installation Gu ide 16 Complian ce Informati on FCC This product has been found to comply with the li mits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection again st harmful interference whe n the equipment is operated in a commercial environ m ...
¿Tienes una pregunta acerca de Perle Systems S-10G-STS?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Perle Systems S-10G-STS, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Perle Systems S-10G-STS probablemente compartirá una forma de solucionarlo.