-
Sanyo CE52LH1R - page 1
CE 52LH1R Instruction Manual LCD Monitor Please read this Instruction book before using your LCD monitor . We wish you many hours of pleasure from your new LCD monitor . ...
-
Sanyo CE52LH1R - page 2
2 SAFETY SAFETY PRECAUTIONS PRECAUTIONS GB Do not allow anything to rest on the power cord. Do not locate this LCD monitor where the cord will be damaged by people walking on it. Do not overload wall outlets and extension cords as this can result in fire or electric shock. A suitable socket outlet must be provided near to the monitor and shall be e ...
-
Sanyo CE52LH1R - page 3
3 Important recycling information. Y our SANYO product is designed and manufactured with high quality materials and components which can be recycled and reused. This symbol means that electrical and electronic equipment, at their end-of-life, should be disposed of separately . In the European Union there are separate collection systems for used ele ...
-
Sanyo CE52LH1R - page 4
4 GB GB The product (meaning the equipment or appliance to which this documentation relates) incorporates Software (the software applica- tions, utilities and modules embedded within the Product) which is owned by Sanyo or its licensors. Before using the product, please read the End-User License Conditions detailed below . If you do not agree to th ...
-
Sanyo CE52LH1R - page 5
5 n Connect the display unit to VGA, BNC and Scart connector as required. 1. Connect the in-line power connector to the connector attached to the LCD monitor as shown above. 2. Connect the power cord of the LCD monitor to a wall outlet. 0 As this product does not have a mains On/Off switch, please ensure your mains plug is easily accessible. 0 The ...
-
Sanyo CE52LH1R - page 6
6 REMOTE CONTROL REMOTE CONTROL GB GB Remote control battery installation Install two "AA" 1.5 volt batteries so that the "+" and "-" marks on the batteries match the "+" and "-" marks inside the unit into the remote control handset. Standby T o switch the monitor on and off. Also see page 7. Recall ...
-
Sanyo CE52LH1R - page 7
7 1 . The LCD display has a Standby light to show there is power . Switching into/from standby mode The Standby mode is used for switching the LCD monitor off for short periods of time. In standby mode the monitor is switched off but is still receiving mains power . l T o turn the monitor into standby mode, press the 4 4 button . The blue power ...
-
Sanyo CE52LH1R - page 8
8 n Advanced settings Use the 5 or 6 button to select Advanced settings and press the 1 or 2 button to enter the sub menu as follows. DCDi (Directional Correlational Deinterlacing) is used to process moving angled edge in deinterlacing to get the smoothest and most natural image. Press the 1 or 2 button on the remote control to select On or O ...
-
Sanyo CE52LH1R - page 9
9 n PIP/POP Setup Use the 5 or 6 button to select PIP/POP Setup and press the 1 or 2 button to enter the sub menu. PIP/POP Mode: Using the 1 or 2 button select the most suitable mode PIP1 , PIP2 , POP or Off . (Please refer to page 12.) 0 When Mode is set to Off , Sub Source and PIP Position will not work. Main Source is used to select input ...
-
Sanyo CE52LH1R - page 10
10 This LCD monitor allows you to set up the following: SETTING PROCEDURE 1. Press and hold the GREEN button on the remote control for 4 seconds. (Installation Mode will appear) 2. Use the 5 or 6 button to highlight each option , use the 1 or 2 button to adjust each option. Press the MENU button to exit the mode. n On Program Select ON program u ...
-
Sanyo CE52LH1R - page 11
11 Select screen size among “Full”, “Zoom”, “Zoom(Caption-IN)”, “Normal” and “Natural wide” by pressing WIDE button on the Remote Control. Provides image to fit width of screen by expanding image width uniformly . This function can be used for enjoying a squeezed video signal with wide video aspect ratio of 16 : 9 screen. When y ...
-
Sanyo CE52LH1R - page 12
12 Using this function, you can enjoy a DVI or Network program and an image ( AV 1 , AV 2 , AV 3 or PC input) at the same time. Press the ON/OFF button on the Remote Control repeatly to select PIP1 , PIP2 , POP or OFF mode. During the PIP/POP mode, press the Main/Sub Picture Swap button will switch the location for main and sub picture. 0 Only the ...
-
Sanyo CE52LH1R - page 13
13 Common specification Power source 120V 50Hz / 60Hz Colour system P AL / NTSC / NTSC4.43/ SECAM A V terminal A V1: Scart CENELEC Standard Input: Composite video, RGB (5V RGB with 5V sync to pin 14) and audio-L/R Output: composite video and audio L/R A V2: BNC Input: RGB, H and V / Y , Pb, Pr and audio L/R Output: RGB, H and V / Y , Pb, Pr A V3: B ...
-
Sanyo CE52LH1R - page 14
14 PC/DVI-D / COMPONENT SIGNAL SUPPOR T TIMING LIST GB GB Compo n en t si gn al s upp or t t i m i n g Re s o lutio n H orizontal f re q u enc y ( K H z ) V e rti cal fre que n cy (H z ) Do t C loc k Fr eque ncy( Mhz) R emar k 7 20x4 80 1 5. 7 3 5 6 0i 1 2. 2 7 S DT V 4 8 0 i 720x 576 15 .625 50 i 13 .50 SD T V 5 76i 720x 480 31 .25 60p 27 SD T V 4 ...
-
Sanyo CE52LH1R - page 15
15 ...
-
Sanyo CE52LH1R - page 16
Printed in U.K. Part No. 1KA6P1P0391-- ...
¿Tienes una pregunta acerca de Sanyo CE52LH1R?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Sanyo CE52LH1R, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Sanyo CE52LH1R probablemente compartirá una forma de solucionarlo.