-
Vector VEC021STC - page 1
1 OWNER’S MANUAL & WARRANTY INFORMA TION JUMP-ST ARTER, AIR COMPRESSOR AND 12 VOL T DC POWER SUPPL Y VEC021STC Portable • Cordless • Rechar geable THIS MANUAL CONT AINS IMPORT ANT INFORMA TION REGARDING SAFETY , OPERATION, MAINTENANCE AND STORAGE OF THIS PRODUCT . BEFORE USING, READ AND UNDERST AND ALL CAUTIONS, W ARNINGS, INSTRUCTIONS AN ...
-
Vector VEC021STC - page 2
2 NOTE: This unit is shipped in a partially charged state, charge for 24 hours using AC method. SAFETY INFORMA TION W ARNING: (W arning statements identify conditions or practices that may result in personal injur y or loss of life) 1) When working with lead acid batteries, always make sure immediate assistance is available in case of accident or e ...
-
Vector VEC021STC - page 3
3 CAUTION: (Caution statements advise against certain conditions and practices that may result in damage to vehicles, appliances and/or The POWER ON BOARD® Jump-starter) IMPORT ANT : Although this unit is delivered in a partially charged state, you must fully charge it with the supplied 120 V olt AC charger for a full 24 hours before using it for ...
-
Vector VEC021STC - page 4
4 CONTENTS 1. INTRODUCTION ....................................................................................... 5 2. USING POWER ON BOARD™ AS A JUMP-ST ART SYSTEM ......................... 5,6 2.1 Easy , Step-by-Step Jump-starting Instructions ................................... 7,8 3. CHARGING/RECHARGING ...................................... ...
-
Vector VEC021STC - page 5
5 1. INTRODUCTION Congratulations on selecting the POWER ON BOARD® JUMP-ST ARTER, AIR COMPRESSOR and 12 VOL T DC POWER SUPPL Y . This compact jump-star ter is unique in the amount of energy it can supply for its size. The internal batter y is a high density sealed, lead-acid batter y that stores and delivers energy comparable to full sized ordinar ...
-
Vector VEC021STC - page 6
6 FIGURE 1A (FRONT VIEW) FIGURE 1B (REAR VIEW) 1. Reverse connection indicator 2. Good connection indicator 3. 12 V olt DC Accessor y Socket with 20 amp overload protection 4. Batter y Level Push Button 5. LED Charging/Batter y Level Indicators 6. Heavy-Duty W elding Quality Jumper Cables 7. Heavy-Duty 350 Amp Copper Clamps 8. Exclusive Quick-Relea ...
-
Vector VEC021STC - page 7
7 2. USING THE POWER ON BOARD® AS A JUMP-ST ART SYSTEM W ARNING: 1. Before using this system to jump-start any vehicle or boat, read and understand all instructions, safety tips, warnings, cautions and first aid information provided in this manual and on the product labeling. Additional important information may also be provided by the vehicle’ ...
-
Vector VEC021STC - page 8
8 2.1 EASY , STEP-BY -STEP JUMP-ST ARTING INSTRUCTIONS 1. T urn OFF vehicle ignition and all accessories (radio, A/C, lights, cell phone, etc.). Place vehicle in park and set the emergency brake. 2. Remove booster clamps from protective holster (Figure 2): simply squeeze the handles and pull down on the clamp. 3 . Procedure for jump-starting a NEGA ...
-
Vector VEC021STC - page 9
9 FIRST AID: • SKIN: If batter y acid comes in contact with skin, rinse immediately with water , then wash thoroughly with soap and water . If redness, pain, or irritation occurs, seek immediate medical attention • EYES: If batter y acid comes in contact with eyes, flush eyes immediately for a minimum of 15 minutes and SEEK IMMEDIA TE MEDICAL A ...
-
Vector VEC021STC - page 10
10 3.2 12 VOL T DC CHARGING 1. Insert one end of the DC/DC charging adapter into the 12 V olt DC accessor y receptacle on the vehicle or boat. 2. Insert the plug at the other end of this charging adapter into the 12 V olt DC accessor y socket receptacle on the front panel of the unit. 3. Charge the unit until the green FULL indicator lights when Ch ...
-
Vector VEC021STC - page 11
11 6. AIR COMPRESSOR/TIRE INFLA TOR IMPORT ANT : Read Instructions Carefully T o A void Possible Injur y Or Proper ty Damage. The built-in 12 V olt DC air compressor is the ultimate compressor for all vehicles, trailer tires and recreational inflatables. Three different sized nozzles are supplied. Each nozzle will clip on the end of the standard ti ...
-
Vector VEC021STC - page 12
12 IMPORT ANT : Always leave the thumb latch in the open position when storing unit. 6.3 INFLA TING OTHER ARTICLES (WITHOUT V AL VE STEM) Inflation of other items requires use of one of the adapters (nozzles). 1. Open the hatch and remove the nozzles noting their storage positions. 2. Insert appropriate adapter (e.g. needle) into connector (chuck) ...
-
Vector VEC021STC - page 13
13 7.1 BULB REPLACEMENT T ools needed - small Phillips screwdriver . 1. Unscrew (counterclockwise) and remove two Phillips screws. 2. Remove the lens cover . 3. Remove the burned-out bulb. 4. Replace with a new bulb (12 V olt 0.2 amp Kr ypton bulb). 5. Snap the lens cover back into place. 6. Replace (clockwise) the screws and carefully tighten. Do ...
-
Vector VEC021STC - page 14
14 TWO YEAR LIMITED W ARRANTY PROGRAM This limited warranty program is the only one that applies to this product, and it sets forth all the responsibilities of V ector Manufacturing, Ltd., regarding this product. There is no other warranty , other than those described herein. This V ector Manufacturing, Ltd. product is warranted, to the original pu ...
-
Vector VEC021STC - page 15
15 ...
-
Vector VEC021STC - page 16
16 ® © 2003 VECTOR MANUF ACTURING, Ltd. • FT . LAUDERDALE, FL 33312 MADE IN CHINA REV .DK051903 ...
¿Tienes una pregunta acerca de Vector VEC021STC?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Vector VEC021STC, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Vector VEC021STC probablemente compartirá una forma de solucionarlo.