-
Snapper I55224, I7244 - page 1
Safety Instructions & Operator’s Manual for TWO STAGE INTERM EDIATE FRAM E SNOW THROWER SERIES 4 MOD ELS I55224 I7244 MODEL NUMBER EXPLA NA TION I 55 22 4 MODEL DESIGNA T ION SERIES DE SIGNA TION ENGINE HP A UGER WIDT H I – Intermediate F rame Mod el 55 – 5.5 Engine HP (Eng ine Horse Pow er) 22 – 22” A uger Wid th 7 – 7.0 Engine HP ...
-
Snapper I55224, I7244 - page 2
2 IMPORTA NT SA FETY INST RUCTIONS WARNING: This pow erful machin e is capable of amput ating hand s and feet and can throw objects that can cause in jury a nd d a m ag e ! Failure to comply wit h the follow ing instruct ions may re sult in serious injur y to the ope rator or other persons. The ow ner of the snow thrower must understand these instr ...
-
Snapper I55224, I7244 - page 3
3 IMPORTA NT SA FETY INST RUCTIONS OPERA TIONA L PRECA U TIONS (Continued From Pre vious Page) 7. DO NOT put hands or fee t near or unde r rotatin g parts. Keep clear of the discharge opening at all times. 8. St art engine only where exhaust fumes w ill be safely dissipated. A llow a brief warm-up pe riod, and practice operation of controls outside ...
-
Snapper I55224, I7244 - page 4
4 TABLE OF CONTENTS SECTION 1 - IMPORTA NT SA FETY INSTRUCTIONS .......................... 2-3 TA BLE OF CO NTENTS ............................................................................ 4 SECTION 2 - OPERA TIN G INSTRUCTIONS ......................................... 5-9 Pre-start Checklist ..................................................... ...
-
Snapper I55224, I7244 - page 5
5 Section 2 - OPERA TING INSTRUCTIONS 2.1 PRE-START CHECK LIST Make the f ollowing check s and perfor m the s ervice required bef ore each start- up. 2.1.1. Check engine oil and add oil as needed to bring level up to the FULL m ark . Refer to engine owner’s m anual for oil spec ifications . 2.1.2. Check guards , chutes, def lectors and covers to ...
-
Snapper I55224, I7244 - page 6
6 Section 2 - OPERA TING INSTRUCTIONS 2.2 ST A RT ING, O PERA TION & STOPPIN G (RECOIL STA RT MODELS) (Go t o Page 8 for Electric St art M odels) 2.2.1. ENGINE 1. T urn fuel s hut off valve to the “ON” position. See Figure 2.3. FIGURE 2.3 2. Ins ert key into ignition switch. See Figure 2.4. 3. Move c hoke contr ol to the choke, “ON ” po ...
-
Snapper I55224, I7244 - page 7
7 Section 2 - OPERA TING INSTRUCTIONS WA RNING Objects can b e thrown b y the snow throw er while it is in operation. Thrown objects could caus e ser ious injury to the operator or by standers. Alway s wear safety goggles or other s uitable ey e protection. Keep people an d pets aw ay from area. 2.2.3. ENGA GING A UGER 1. Move auger contr ol lever ...
-
Snapper I55224, I7244 - page 8
8 Section 2 - OPERA TING INSTRUCTIONS 2.2 ST A RT ING, O PERA TION & STOPPIN G (ELECTRIC STA RT M ODELS) (Go to Page 6 for Recoil Start Models) WA RNING DO NOT use an electrical extensio n cord that is damaged. A damaged electrical exten sion cord could cause a shock or fire. Thoroughly ins pect electrical extension cord before u sing machine. ...
-
Snapper I55224, I7244 - page 9
9 Section 2 - OPERA TING INSTRUCTIONS WA RNING Objects can b e throw n by the snow thrower w hile it is in operation. Thrown objects could cause serious injury to the operator or bystande rs. A lways w ear safety goggle s or other suita ble eye protection. Ke ep people and pets a way from are a. 2.2.9. ENGAGING A UGER 1. Pull auger contr ol lever a ...
-
Snapper I55224, I7244 - page 10
10 Section 3 - MA INTENA NCE WA RNING DO NOT attempt an y adjustments, maintenance, service, or repair s, with engine running. Stop auger. Stop engine. Remove key. Dis connect spark plug wire an d secure wire aw ay from spark plu g. 3.1 INTRODUCT ION To retain the quality of the snow thrower, use only genuine SNAPPER replacem ent parts. Contac t a ...
-
Snapper I55224, I7244 - page 11
11 Section 3 - MA INTENA NCE 3.4 ANNUA LLY (END OF EA CH SEA SON) Perfor m all m aintenance as described in the m aintenance schedule. 3.4.1. Engine Refer to engine owner’s manual for service instru cti on s. 3.4.2. Spark Plug Refer to engine owner’s manual for service instru cti on s. 3.5 STORA GE PROCEDURE Refer to the Engine O wner’s Manua ...
-
Snapper I55224, I7244 - page 12
12 Section 4 - REPA IR & A DJUSTMENTS WA RNING DO NOT attempt an y adjustments, maintenance, service, or repair s, with engine running. Stop auger. Stop engine. Remove key. Dis connect spark plug wire an d secure wire aw ay from spark plu g. 4.1 AUGE R and WHEEL DRIVE BELT A D JUSTM ENT /REPLACEMENT W hen oper ating mac hine release the auger c ...
-
Snapper I55224, I7244 - page 13
13 Section 4 - REPA IR & A DJUSTMENTS WA RNING DO NOT attempt an y adjustments, maintenance, service, or repair s, with engine running. Stop auger. Stop engine. Remove key. Dis connect spark plug wire an d secure wire aw ay from spark pl ug. Before tilting machine, drain all the fuel from fuel tank. A llow engine to run, outdoors where fumes ca ...
-
Snapper I55224, I7244 - page 14
14 Section 4 - REPA IR & A DJUSTMENTS WA RNING DO NOT attempt an y adjustments, maintenance, service, or repair s, with engine running. Stop auger. Stop engine. Remove key. Dis connect spark plug wire an d secure wire aw ay from spark pl ug. Before tilting machine, drain all the fuel from fuel tank. A llow engine to run, outdoors where fumes ca ...
-
Snapper I55224, I7244 - page 15
15 Section 4 - REPA IR & A DJUSTMENTS 4.1.5. GROUND SPEED ADJUSTMENT NOTE: It is rec om m ended to r em ove the drive system cover and chec k r ubber drive tire engagem ent with drive disc when adjus ting ground speed. 1. Tilt mac hine fo rward to gain acc ess to drive s y s tem area. Secure m achine in the tilted pos ition to prevent tipping o ...
-
Snapper I55224, I7244 - page 16
16 Section 4 - REPA IR & A DJUSTMENTS 4.1 .8. SINGLE HA NDLE CONT ROL A DJUSTMENT ( 7 HP Models On ly) IMPO RTANT: Standing in the operator’s pos ition, the left handle bar lever is for w heel drive engagement and disengagem ent. T he right handle bar lever is f or auger/im peller engagem ent and disengagem ent. Hold both levers down to handl ...
-
Snapper I55224, I7244 - page 17
17 Section 4 - REPA IR & A DJUSTMENTS WA RNING DO NOT attempt an y adjustments, maintenance, service, or repair s, with engine running. Stop auger. Stop engine. Remove key. Dis connect spark plug wire an d secure wire aw ay from spark pl ug. Before tilting machine, drain all the fuel from fuel tank. A llow engine to run, outdoors where fumes ca ...
-
Snapper I55224, I7244 - page 18
18 TROUBLESHOOTING PROBL EM PROBABLE CA USE CORRECTIVE A CT ION Engine Will Not Start 1. Fuel tank empty. 1. Fill fuel tank with fresh fuel/oil mix . Using Recoil Starter 2. Engine needs choking and priming. 2. Mo ve choke control to “C HOKE” position. Push primer bulb three times. 3. Spark plug wire disconnected. 3. Place spark plug wire onto ...
-
Snapper I55224, I7244 - page 19
19 3 YEA R LIMITED WA RRA NTY For thr ee ( 3) years from purc hase date f or the original purc haser's residential, non- com m erc ial use, SNAPPER , through any authorized SNA PPER dealer will replace, fr ee of c harge (exc ept for taxes where applic able), any part or parts found upon exam ination by the factor y at Mc Donough, Georgia, to b ...
-
Snapper I55224, I7244 - page 20
20 Safety Instructions & Operator’s Manual for TWO STAGE INTERMEDIATE FRAME SNOW THROWER SERIES 4 IMPORTA NT Snapper products are built using engines that meet or exceed all applicable emissions requirements on the date manufac tured. The labels on those e ngines contain very important emissions informa tion and critical safety warn ings. Rea ...
¿Tienes una pregunta acerca de Snapper I55224, I7244?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Snapper I55224, I7244, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Snapper I55224, I7244 probablemente compartirá una forma de solucionarlo.