-
CDA HVN 32 - page 1
Customer Car e Department • The G r oup Ltd. • Harby Road • Langar • Nottinghamshi r e • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www .cda.eu HVN 32 .. - T ouc h Contr ol Induction C ooking Hob Manual for Inst allation, Use and Maintenanc e ...
-
CDA HVN 32 - page 2
2 Important This appliance is designed and manufactur ed solely for the cooking of domestic (household) f ood and is not suitable for an y non domestic application and ther efore should not be used in a commer cial envir onment. The applianc e guar antee will be void if the applianc e is used within a non domestic en vironment i.e. a semi commer ci ...
-
CDA HVN 32 - page 3
3 Befor e Using for the Fir st Time – Read the instructions car efully before installing and using the applianc e. – After unpacking the appliance, make sure it is not damaged. In case of doubt, do not use the appliance and contact your supplier or a qualified engineer . – Remove all packaging and do not lea ve the pac king mat erial (plastic ...
-
CDA HVN 32 - page 4
4 Important Saf eguar ds and Recommendations – Do not carry out any cleaning or maintenance without fir st disc onnecting the appliance from the electrical supply. – During and after use of the hob, certain parts will bec ome hot. Do not touch hot parts. – After use alw ays ensur e that the controls ar e in the OFF position. – Household app ...
-
CDA HVN 32 - page 5
5 3 4 7 8 5 6 1 2 Featur es and T echnical Data Cooking Zones 1 . Induction cooking zone Ø 1 40 mm - 1 400 W 2. Induction cooking zone Ø 2 1 0 mm - 2200 W (3000 W with Booster function) Note: The Nominal and Booster P ower ma y change depending on the size and material of the pan set on the cooking zone. T ouch-Contr ol Description 3. ON/OFF key ...
-
CDA HVN 32 - page 6
6 Use of Induction Hob Not es: – Each selection (by pr essing one of the keys) is indicated by an acoustic signal (beep). – User interface initial calibration: this featur e is for the keyboar d calibration, to adapt the sensibility of the keys to the final mechanical, envir onmental and user conditions. Any time the cooktop is connected to the ...
-
CDA HVN 32 - page 7
7 Thermal Pr ot ection The induction cooktop is fitted with saf ety devices to protect the electronic system and each cooking zone from overheating. Overheating o f Cooking Zone – Cooking zone OFF : the cooking zone display shows " H " and " C " alternating or just " C " blinking. – Cooking zone ON : the cooking zo ...
-
CDA HVN 32 - page 8
8 The ceramic c ooktop is fitted with induction c ooking zones. These zones, shown by painted disks on the cer amic surface, are contr olled by a touch contr ol system. Induction Cooking Syst em When your induction hob is switched on and a cooking zone has been selected, the electronic circuits produc e induced curr ents that instantaneously heat t ...
-
CDA HVN 32 - page 9
9 How T o T urn the T ouc h Contr ol ON and OFF Switc hing ON Press the key and keep it pr essed until the touch contr ol is lighted. The displays of the cooking z ones read " 0 ". Not es: – If the safety key-lock protection is active, the t ouch control can be turned ON only after having deactiv ated this pr otection. – Auto swit ch- ...
-
CDA HVN 32 - page 10
1 0 OR A fterheat in C ooking Zone/s When switching off a cooking zone (power level 0 ), if the temperatur e of the zone is too warm to be touched the display will show alternat ely " H " and " 0 ". Whenever the touch control is switc hed off, the residual heat is shown by a static " H ". Av oid touching the hob surfac ...
-
CDA HVN 32 - page 11
1 1 Booster F unction Rear C ooking Zone Only This function allows the cooking zone to operate at the Booster maximum power (above the nominal power) for maximum 1 0 minutes; it could be used, for example, to rapidly heat up lar ge amount of water . This function is av ailable for the rear cooking zone only . T o activate the Booster function, the ...
-
CDA HVN 32 - page 12
1 2 Safety K ey -Loc k to Pr otect Childr en This function locks the touc h-control k eys against un wanted activation. T o activate the key-loc k press the key ; the indicator light above the key symbol will light up. – Cooking zone/s oper ating (power level alr eady set) - with the key-loc k pr otection active it is only possible to switc h off ...
-
CDA HVN 32 - page 13
1 3 Pr ogr am for A utomatic Swit ching OFF o f One Cooking Zone This function permits to set a timer fr om 1 to 99 minutes for automatic turning OFF of one cooking zone only . Not e: It is not possible t o set this pr ogram f or both the cooking zones. With the touc h control swit ched ON : – Press the timer keys or ; a beep sounds and the timer ...
-
CDA HVN 32 - page 14
1 4 Oper ation Time Limit o f Cooking Zones Each cooking zone is automatically switc hed OFF after a maximum preset time if no oper ation is performed. The maximum preset time limit depends on the set power level, as illustrated in this sc hedule. Each operation on the cooking hob by using the keys , will reset the maximum oper ation time at its in ...
-
CDA HVN 32 - page 15
1 5 Err or Code on the Displa y/s If an err or message appears on the display/s (the displa y/s show/s " F " and another char acter alternating - e.g. " F " and " A ", " F " and " 0 ", ..... ) : 1 . Disconnect the cooktop from the mains. 2. Reconnect the c ooktop and turn it on. 3. W ait for about t ...
-
CDA HVN 32 - page 16
1 6 Cleaning and Maintenanc e Cleaning the Cer amic Hob – Befor e you begin cleaning make sure that the hob is s witc hed off. – Remove spillages and other types of incrust ations. – Dust or food particles can be r emoved with a damp cloth. – If you use a detergent, please make sure that it is not abrasive or scouring. Abrasive or sc ouring ...
-
CDA HVN 32 - page 17
1 7 TIPS FOR INS T ALLA TION Installation CAUTION: This appliance shall only be serviced b y authorised personnel. – This appliance is to be installed only by an authorised person accor ding to the current local regulations and in observ ation of the manufacturer’s instructions. – Incorrect installation, for which the manufacturer accepts no ...
-
CDA HVN 32 - page 18
1 8 This cooktop can be built into a working surface 30 to 40 mm thick and 600 mm deep. In order to install the ceramic hob into the kitchen fixture, a hole with the dimensions shown in figure 3 has to be made, keeping in consider ation the following: – The cooktop shall not be installed directly above a dishwasher , fridge, fr eezer , washing ma ...
-
CDA HVN 32 - page 19
1 9 Fast ening the Cookt op Each cooktop is supplied with a set of tabs and scr ews to fasten it on units with a w orking surface from 3 to 4 cm deep. The kit includes 4 tabs A and 4 self-thr eading screw s B (fig. 6). – Cut the unit. – T urn the hob upside down and rest the glass side on a cloth. – Spread the seal C ar ound the edge of the h ...
-
CDA HVN 32 - page 20
20 Mains Electricity Connection Incorr ect installation ma y be dangerous and the manufacturer can no t be held responsible. W arning! This appliance must be earthed The manufacturer declines all responsibility f or any problem caused b y failure to observ e this rule. THIS APPLIANCE MUST BE CONNECTED T O THE MAINS SUPPL Y B Y A CO MPETENT PERSON, ...
-
CDA HVN 32 - page 21
2 1 Connection o f the P ow er Supply Cable Unhook the terminal boar d cover by inserting a scr ewdriver into the two hooks A (fig. 8). Open the cable gland by unscrewing scr ew F (fig. 9), unscrew the terminal scr ews and remove the cable. The new supply cable, of suitable type and section, is connected to the terminal board following the diagram ...
-
CDA HVN 32 - page 22
22 Appliance Servicing CDA pr ovide a quality and effective after -sales service to c over all your servicing needs. Please attac h your r eceipt to this page f or safekeeping. Please help us to help you by ha ving the following inf ormation available when booking a servic e-call: 1 . Model type, make and model – see the product data plate. 2. Ev ...
-
CDA HVN 32 - page 23
23 ...
-
CDA HVN 32 - page 24
Customer Car e Department • The G r oup Ltd. • Harby Road • Langar • Nottinghamshi r e • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www .cda.eu T o contact our Customer Car e Department, or for Service, please contact us on the det ails below . Cod. 1 1 035 7 8 - ß 5 ...
¿Tienes una pregunta acerca de CDA HVN 32?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con CDA HVN 32, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con CDA HVN 32 probablemente compartirá una forma de solucionarlo.