-
Agilent Technologies HFBR 5203 - page 1
A TM M ultimode Fiber Transceivers for SONET OC-3/SDH STM-1 in Low Cost 1x9 P ackage Style T echnical Data Features • Full Compliance with ATM Forum UNI SONET OC-3 Multimode Fiber Physical Layer Specification • Multisourced 1 x 9 Package Style with Choice of Duplex SC or Duplex ST* Receptacle • W ave Solder and Aqueous W ash Process Compatibi ...
-
Agilent Technologies HFBR 5203 - page 2
2 design complies with the maximum height allowed for the duplex SC connector over the entire length of the package. The optical subassemblies utilize a high volume assembly process together with low cost lens elements which result in a cost effective building block. The electrical subassembly con- sists of a high volume multilayer printed circuit ...
-
Agilent Technologies HFBR 5203 - page 3
3 DATA OUT SIGNAL DETECT OUT DATA IN ELECTRICAL SUBASSEMBLY QUANTIZER IC DRIVER IC TOP VIEW PIN PHOTODIODE DUPLEX ST RECEPTACLE OPTICAL SUBASSEMBLIES LED PREAMP IC DIFFERENTIAL SINGLE-ENDED DIFFERENTIAL Figure 2. Package Outline Drawing. Figure 1a. ST Block Diagram. 39.12 (1.540) MAX. AREA RESERVED FOR PROCESS PLUG 12 ...
-
Agilent Technologies HFBR 5203 - page 4
4 Figure 3. Pin Out Diagram. 25.4 (1.000) MAX. 24.8 (0.976) 42 (1.654) MAX. 5.99 (0.236) 12.7 (0.500) 12.0 (0.471) MAX. 0.5 (0.020) 3.3 ± 0.38 (0.130) (± 0.015) + 0.08 - 0.05 + 0.003 - 0.002 + 0.25 - 0.05 + 0.010 - 0.002 20.32 ± 0.38 (± 0.015) HFBR-5103T DATE CODE (YYWW) SINGAPORE 3.2 (0.126) 2.6? ...
-
Agilent Technologies HFBR 5203 - page 5
5 Agilent LED technology has produced 800 nm LED and 1300 nm LED devices with lower aging characteristics than normally associated with these technolo- gies in the industry. The industry convention is 3 dB aging for 800 nm and 1.5 dB aging for 1300 nm LEDs. The 1300 nm HP LEDs are specified to experience less than 1 dB of aging over normal commerci ...
-
Agilent Technologies HFBR 5203 - page 6
6 Figure 5. Transceiver Relative Optical Power Budget at Constant BER vs. Signaling Rate. Figure 6. Bit Error Rate vs. Relative Receiver Input Optical Power. illustrates the typical trade-off between link BER and the receivers input optical power level. Transceiver Jitter Performance The Agilent 1300 nm transceivers are designed to operate per the ...
-
Agilent Technologies HFBR 5203 - page 7
7 NO INTERNAL CONNECTION NO INTERNAL CONNECTION HFBR-520X TOP VIEW V EE RD RD SD V CC V CC TD TD V EE 123456789 C1 C2 L1 L2 R2 R3 R1 R4 C5 C3 C4 R9 R10 V CC FILTER AT V CC PINS TRANSCEIVER R5 R7 R6 R8 C6 RD RD SD V CC TD TD TERMINATION AT PHY DEVICE INPUTS NOTES: THE SPLIT-LOAD TERMINATIONS FOR ECL SIGNALS NEED TO BE LOCATE ...
-
Agilent Technologies HFBR 5203 - page 8
8 Board Layout - Art W ork The Applications Engineering group is developing Gerber file art work for a multilayer printed circuit board layout incorporating the recommendations above. Contact your local Agilent sales representative for details. Board Layout - Mechanical For applications interested in providing a choice of either a duplex SC or a du ...
-
Agilent Technologies HFBR 5203 - page 9
9 Electromagnetic Interference (EMI) Most equipment designs utilizing these high speed transceivers from Agilent will be required to meet the requirements of FCC in the United States, CENELEC EN55022 (CISPR 22) in Europe and VCCI in Japan. These products are suitable for use in designs ranging from a desktop computer with a single transceiver to a ...
-
Agilent Technologies HFBR 5203 - page 10
10 Figure 10. Relative Input Optical Power vs. Eye Sampling Time Position. Figure 9. Transmitter Output Optical Spectral Width (FWHM) vs. Transmitter Output Optical Center Wavelength and Rise/Fall Times. Regulatory Compliance Table Feature Test Method Performance Electrostatic Discharge MIL-STD-883C Meets Class 2 (2000 to 3999 V olts) (ESD) to the ...
-
Agilent Technologies HFBR 5203 - page 11
11 Transceiver Reliability and Performance Qualification Data The 1 x 9 transceivers have passed Agilent reliability and performance qualification testing and are undergoing ongoing quality monitoring. Details are available from your Agilent sales representative. These transceivers are manufactured at the Agilent Singapore location which is an ISO ...
-
Agilent Technologies HFBR 5203 - page 12
12 HFBR-5203, -5204, and -5205 Series Recommended Operating Conditions Parameter Symbol Min. Typ. Max. Unit Reference Ambient Operating Temperature T A 07 0 ° C Supply Voltage V CC 4.75 5.25 V Data Input Voltage - Low V IL - V CC -1.810 -1.475 V Data Input Voltage - High V IH - V CC -1.165 - 0.880 V Data and Signal Detect Output Load R L 50 Ω No ...
-
Agilent Technologies HFBR 5203 - page 13
13 HFBR-5203, -5204 and -5205 Series Transmitter Electrical Characteristics (T A = 0 ° C to 70 ° C, V CC = 4.75 V to 5.25 V) Parameter Symbol Min. Typ. Max. Unit Reference Supply Current I CC 145 185 mA Note 3 Power Dissipation P DISS 0.76 0.97 W Data Input Current - Low I IL -350 0 µ A Data Input Current - High I IH 14 350 µ A HFBR-5203, -5204 ...
-
Agilent Technologies HFBR 5203 - page 14
14 Agilent offers two such compatible duplex Push-Pull ST connectored jumper cable assemblies to assist you in your evaluation of these products. These cables may be purchased from Agilent with the following part numbers. 1. HFBR-XXX001 A duplex cable 1 meter long assembled with 62.5/125 µ m fiber and Duplex Push-Pull ST connector plugs on both en ...
-
Agilent Technologies HFBR 5203 - page 15
15 HFBR-5203/-5203T Receiver Optical and Electrical Characteristics (T A = 0 ° C to 70 ° C, V CC = 4.75 V to 5.25 V) Parameter Symbol Min. Typ. Max. Unit Reference Input Optical Power P IN Min. (W) -26 dBm avg. Note 16 Minimum at Window Edge Output Optical Power P IN Min. (C) -27 dBm avg. Note 17 Minimum at Eye Center Input Optical Power Maximum ...
-
Agilent Technologies HFBR 5203 - page 16
16 HFBR-5204/-5204T Receiver Optical and Electrical Characteristics (T A = 0 ° C to 70 ° C, V CC = 4.75 V to 5.25 V) Parameter Symbol Min. Typ. Max. Unit Reference Input Optical Power P IN Min. (W) -29 dBm avg. Note 16 Minimum at Window Edge Figure 10 Input Optical Power P IN Min. (C) -30 dBm avg. Note 17 Minimum at Eye Center Figure 10 Input Opt ...
-
Agilent Technologies HFBR 5203 - page 17
17 HFBR-5205/-5205T Transmitter Optical Characteristics (T A = 0 ° C to 70 ° C, V CC = 4.75 V to 5.25 V) Parameter Symbol Min. Typ. Max. Unit Reference Output Optical Power BOL P O -19 -14 dBm avg. Note 9 62.5/125 µ m, NA = 0.275 Fiber EOL -20 Output Optical Power BOL P O -22.5 -14 dBm avg. Note 9 50/125 µ m, NA = 0.20 Fiber EOL -23.5 Optical E ...
-
Agilent Technologies HFBR 5203 - page 18
18 HFBR-5205/-5205T Receiver Optical and Electrical Characteristics (T A = 0 ° C to 70 ° C, V CC = 4.75 V to 5.25 V) Parameter Symbol Min. Typ. Max. Unit Reference Input Optical Power P IN Min. (W) -30 dBm avg. Note 16 Minimum at Window Edge Figure 10 Input Optical Power P IN Min. (C) -31 dBm avg. Note 17 Minimum at Eye Center Figure 10 Input Opt ...
-
Agilent Technologies HFBR 5203 - page 19
19 expressed as a percentage. With the transmitter driven by a 25 MBd (12.5 MHz square-wave) input signal, the average optical power is measured. The data “1” peak power is then calculated by adding 3dB to the measured average optical power. The data “0” output optical power is found by measuring the optical power when the transmitter is dr ...
-
Agilent Technologies HFBR 5203 - page 20
www.semiconductor.agilent.com Data subject to change. Copyright © 1999 Agilent Technologies, Inc. Obsoletes 5963-5774E (2/95) 5965-9729E (11/99) ...
¿Tienes una pregunta acerca de Agilent Technologies HFBR 5203?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Agilent Technologies HFBR 5203, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Agilent Technologies HFBR 5203 probablemente compartirá una forma de solucionarlo.