-
Solid State Logic 82S6XL090A - page 1
E Signature™ Channel Owner ’ s Manual ...
-
Solid State Logic 82S6XL090A - page 2
...
-
Solid State Logic 82S6XL090A - page 3
Solid State Logic Super -Analogue™ Outboar d Owner ’s Manual 82S6XL090A XL ogic SIGNATURE CHANNEL ...
-
Solid State Logic 82S6XL090A - page 4
XLogic E Signature™ Channel Owner ’ s Manual As resear ch and development is a continual process, Solid State Logic r eserves the right to change the features and specifications described her ein without notice or obligation E&OE Initial Release (Rev . 0A), November 2005 Solid State Logic Begbroke, Oxford, England, OX5 1RU • +44 (0)1865 8 ...
-
Solid State Logic 82S6XL090A - page 5
Page 1 Contents 1.0 Introduction 3 2.0 Safety Considerations 4 Safety W arnings 4 3.0 Installation 6 Setting the mains voltage selector 6 Mounting 7 Connections 7 4.0 Operation 9 Input Section 9 Listen Mic Compressor 9 Dynamics Section 10 Compressor/Limiter 10 Expander/Gate 1 1 Filter Section 1 1 Equaliser Section 12 Output Section 12 5.0 Signal Ro ...
-
Solid State Logic 82S6XL090A - page 6
Page 2 XLogic E Signature™ Channel (front) XLogic E Signature™ Channel (rear) Solid State Logic XL ogic SIGNATURE CHANNEL INPUT LCOMP DRIVE MIC LINE 3RD 2ND LESS MORE +20 -20 +70 +20 0 DYNAMICS RELEASE COMPRESSOR GATE 3 6 10 14 20 RATIO RELEASE RANGE FILTERS LF LMF HMF HF OUTPUT T/HOLD T/HOLD KHz GAIN GAIN GAIN GAIN GAIN Hz Hz KHz Q KHz Q KHz P ...
-
Solid State Logic 82S6XL090A - page 7
Page 3 Introduction 1.0 Introduction The XLogic E Signature Channel unit brings the classic sound of the original early 1980s E Series console to the outboard rack of today’s artists and pr oducers. The XLogic E Signatur e Channel delivers the choice of selectable transformer driven or V ariable Harmonic Drive (VHD) mic amps and the world renowne ...
-
Solid State Logic 82S6XL090A - page 8
Page 4 XLogic E Signature™ Channel Owner ’ s Manual 2.0 Safety considerations This section contains definitions and warnings, and practical information to ensure a safe working envir onment. Please take time to read this section befor e undertaking any installation work. 2.1 Definitions ‘Maintenance’ All maintenance must be carried out by f ...
-
Solid State Logic 82S6XL090A - page 9
Page 5 Safety Considerations Mains Supply and Phases Solid State Logic equipment is designed for connection to a single phase supply with the Neutral conductor at earth potential – category TN – and is fitted with a protective fuse in the Live conductor only . It is not designed for use with Phase (Live) and Neutral connections reversed or wher ...
-
Solid State Logic 82S6XL090A - page 10
Page 6 XLogic E Signature™ Channel Owner ’ s Manual 3.0 Installation 3.1 V oltage Selection Before connecting the mains supply ensur e that the voltage range selector next to the IEC socket on the r ear of the unit is correctly set. The input setting must be confirmed befor e applying power . The input module can be configured to be one of 4 vo ...
-
Solid State Logic 82S6XL090A - page 11
Page 7 3.2 Mounting This unit is designed to be rack-mounted. It is 1 RU (44.5mm/1.75 inch) high, its depth is: 325 mm/12.8 inches not including heatsink. 365 mm/14.3 inches including heatsink 400 mm/15.75 inches including connectors The XLogic E Signature Channel units incorporate r einforcement brackets into the chassis and so ar e suitable for d ...
-
Solid State Logic 82S6XL090A - page 12
Page 8 XLogic E Signature™ Channel Owner ’ s Manual XLogic E Signature™ Channel Block Diagram ADC Option Drive Mic Gain Mic Amp 1 Mic Amp 2 Mic In Line Gain Line Amp Line In ON LINE PAD 48V IN Phase -1 Threshold LComp Ø Ext Key Input Key In 4 Band Equaliser HP & LP Filters KEY DYN Dynamics Link In/Out LINK DYN IN EQ DYN PRE EQ IP FLT DYN ...
-
Solid State Logic 82S6XL090A - page 13
Page 9 Installation and Operation 4.0 Operation The XLogic E Signature Channel unit is a 1U rack mounting unit containing a complete set of signal pr ocessing based upon the SL 4000 E Series channel strip – Input, Compressor/Limiter , Expander/Gate, Hi and Lo pass Filters and Equaliser . The signal processing or der can be changed and the EQ and ...
-
Solid State Logic 82S6XL090A - page 14
Page 10 XLogic E Signature™ Channel Owner ’ s Manual 4.3 Dynamics Section The Dynamics section of the XLogic E Signature Channel unit comprises a compr essor/limiter and an expander/gate, both of which use the same gain change element. The design returns faithfully to the circuit and key components which defined the sound of the original E Seri ...
-
Solid State Logic 82S6XL090A - page 15
Page 11 Installation and Operation 4.5 Expander/Gate The Expander/Gate section can act either as a ∞ :1 Gate or , when the EXP switch is pr essed, as a 2:1 Expander . RANGE – Determines the depth of gating or expansion. When turned fully anti-clockwise, the Expander/Gate section will be inactive. When turned fully clockwise, a range of 40dB can ...
-
Solid State Logic 82S6XL090A - page 16
Page 12 XLogic E Signature™ Channel Owner ’ s Manual 4.7 Equaliser Section The XLogic E Signature Channel unit equaliser section defaults to the original ‘Br own Knob’ circuit that was standard on all early pr oduction E Series consoles. The two parametric mid-band sections feature SSL ’s classic logarithmically symmetric design that ensu ...
-
Solid State Logic 82S6XL090A - page 17
Page 13 Installation and Operation 5.0 Signal Routing Channel Processing Order There ar e two switches that control the or der of the signal pr ocessing elements. These are Filters to INPUT and Dynamics PRE EQ . The table below shows the effect of these: Side Chain Processing Order The EQ and Filter sections can be assigned to the dynamics side cha ...
-
Solid State Logic 82S6XL090A - page 18
Page 14 XLogic E Signature™ Channel Owner ’ s Manual Stop looking – we left this page blank… ...
-
Solid State Logic 82S6XL090A - page 19
Page 15 Appendix Appendix A – Internal Links and Fuses Fuses (Mains Inlet) The mains inlet contains a single 1 amp 1.25" time delay fuse (SSL Part No. 35FJJ310). T o change it disconnect the mains inlet, then using a small screwdriver prise open the mains selector cover (see illustration on page 6.). Under this cover is a removable carrier t ...
-
Solid State Logic 82S6XL090A - page 20
Page 16 XLogic E Signature™ Channel Owner ’ s Manual Appendix B – Connector Details Link Location: Rear Panel Conn' Type: TRS Jack Socket Pin Description Tip Link Bus * Ring Link Bus * Sleeve Chassis * Tip and Ring are linked to allow use of mono jacks Key In Location: Rear Panel Conn' Type: XLR Female Pin Description 1 Chassis 2 Au ...
-
Solid State Logic 82S6XL090A - page 21
Page 17 Appendix Appendix C – Performance Specification The following pages contain audio performance specification figures for the XLogic E Signatur e Channel unit. No other Solid State Logic products ar e covered by this document and the performance of other Solid State Logic products can not be inferr ed from the data contained her ein. Measur ...
-
Solid State Logic 82S6XL090A - page 22
Page 18 XLogic E Signature™ Channel Owner ’ s Manual Microphone Input 2 (Electronically Balanced) Measurement Conditions Signal applied to Mic Input and measured at Output. Pad switched out and Mic Gain contr ol set to +20dB. Gain Continuously variable from +20dB to +70dB Independently switchable 22dB Pad available Input Impedance > 1.2kΩ ...
-
Solid State Logic 82S6XL090A - page 23
Page 19 Appendix Equaliser This is a four band equaliser that can be switched between two differ ent sets of curves; one based on SSL ’s ‘02’ (‘Brown Knob’) EQ and the other based on the latest version of the classic ‘242’ E Series (‘Black Knob’) EQ. High and low pass filters are also available. HF Band controls: Frequency V ariab ...
-
Solid State Logic 82S6XL090A - page 24
Page 20 XLogic E Signature™ Channel Owner ’ s Manual Dynamics The unit contains a complete dynamics section, the functions of which split into two areas; a Compressor/Limiter and an Expander/Gate. Compressor/Limiter Controls: Ratio (slope) V ariable from 1 to infinity (limit) Threshold V ariable from +10dB to –30dB Attack Slope Normally ‘Ov ...
-
Solid State Logic 82S6XL090A - page 25
Page 21 Appendix Appendix D - Calibration Information The XLogic E Signature Channel unit is factory calibrated and should only need calibration if a potentiometer or other component has been replaced or if it is suspected that ther e is a problem with calibration. In all of the following instructions it is assumed that the lid has been removed and ...
-
Solid State Logic 82S6XL090A - page 26
Page 22 XLogic E Signature™ Channel Owner ’ s Manual Meter Calibration Equipment Required: Calibrated audio oscillator and audio level meter T est Signal: 1kHz sinewave @ +24dBu Input and Output: Oscillator to Line Input and Output to the audio level meter Unit Setup: 1. Set both Line Gain and Output Gain to indent (0dB). 2. Check for +24dBu ou ...
-
Solid State Logic 82S6XL090A - page 27
Page 23 Appendix 4. Switch BLK in and re-adjust HMF Frequency for maximum level. 5. Adjust VR16 for +18dBu ±0.25dB. 6. Reset HMF Gain to its centre indent position and release the BLK switch. Re- check the audio level meter for 0dBu. HF EQ – Maximum Gain Adjustment: 1. Ensure that the BLK switch is released. 2. Set HF Gain to maximum and select ...
-
Solid State Logic 82S6XL090A - page 28
Page 24 XLogic E Signature™ Channel Owner ’ s Manual Appendix E – Physical specification * Depth: 363mm / 14.3 inches casing and heatsink, excluding front panel knob(s) and rear connectors 425mm / 16.75 inches including connectors, excluding front panel knob(s) Height: 44.5mm / 1.75 inches (1 RU) W idth: 444mm / 17.5 inches casing only 481mm ...
-
Solid State Logic 82S6XL090A - page 29
Page 25 Appendix Notes ...
-
Solid State Logic 82S6XL090A - page 30
Page 26 XLogic E Signature™ Channel Owner ’ s Manual ...
¿Tienes una pregunta acerca de Solid State Logic 82S6XL090A?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Solid State Logic 82S6XL090A, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Solid State Logic 82S6XL090A probablemente compartirá una forma de solucionarlo.