-
AOC 203P - page 1
41G2001-615-1A 英文 ...
-
AOC 203P - page 2
TABLE OF CONTENTS FOR YOUR SAFETY -------------------------------------------------- 1 SAFETY PRECAUTIONS -------------------------------------- 2 SPECIAL NOTES ON LCD MONITORS ------------------- 3 BEFORE YOU OPERATE THE MONITO R --------------------- 3 FEATURES -------------------------------------------------------- 3 PACKING LIST -------------- ...
-
AOC 203P - page 3
2 Before operating the monitor, pleas e read this manual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Pa rt 15 of the FCC Ru les ...
-
AOC 203P - page 4
PRECAUTIONS z Do not use the monitor near water, e.g. near a bathtub, w ashbowl, kitchen sink, laundry tub, sw imming pool or in a we t basement. z Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a person and c ause serious damage to the appliance. Use only a cart or stand recommended by the manufa ...
-
AOC 203P - page 5
SPECIAL NOTES ON LCD MONITORS The following symptoms are normal w ith LCD monitor and do not indicate a problem. NOTES • Due to the nature of the fluoresc ent light, the screen may flicker during initial use. Turn off the Power Sw it ch and then turn it on again to make sure the flicker disappears. • You may find slightly uneven br ightness on ...
-
AOC 203P - page 6
INSTALLATION INSTRUCTIONS SWIVEL BASE Install Remove Figure 1 Installing and Removing the Swivel Base POWERCORD Pow er Source: 1. Make sure that the power cord is the correct type required in y our area. 2. This LCD monitor has an External universal power supply that allow s operation in either 100/120V AC or 220/240V AC voltage area (No user adjus ...
-
AOC 203P - page 7
CONTROLS AND CONNECTORS VIDEO CABLE Connecting the signal Cable : Connect one end of the 15-pin D-Sub cable to the back of the monitor and connect the other end to the co mputer’s D-Sub port. Connect one end of the 24-pin DVI cabl e to the back of the monitor and connect the other end to the computer’s DVI port. Connecting the Power Cord: Conne ...
-
AOC 203P - page 8
ADJUSTING THE VIEWING ANGLE • For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor’ s angle to your ow n preference. • Hold the stand so y ou do not t opple the monitor w hen you change the monitor’s angle. • You are able to adjust the monitor’s angle from -5 ° to 25 ° . Figure 3 NOTES ...
-
AOC 203P - page 9
OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the moni tor on or off. The other control buttons are located on the front panel of the monitor (See Figure 4). By changing these settings, the picture can be adjus ted to your personal preferences. • The power cord should be connected. • Connect the video cable from the ...
-
AOC 203P - page 10
FRONT PANEL CONTROL • Pow er Button / Powe r Indicator: Press this button to turn the monitor ON or OFF. Blue — Power On mode. Orange — Off mode. • MENU / ENTER : Activate OSD menu when OSD is OFF or activate/de-activate adjustment function w hen OSD is ON or Exit OS D menu when in Volume Adjust OSD status. • Auto Adjust button / Exit: 1. ...
-
AOC 203P - page 11
HOW TO ADJUST A SETTING 1. Press the MENU-button to activate the OSD window . 2. Press < or > to navigate through t he functions. Once the desired function is highlighted, press t he MENU-button to activate it. If the function selected has a sub-menu, press < or > again to navigate through the sub- menu functions. Once the desired f unc ...
-
AOC 203P - page 12
ADJUSTING THE PICTURE The descriptions for function control LEDS Main Menu Item Main Menu Icon Sub Menu Item Sub Menu Icon Description Reset Value Contrast Contrast from Digital- register. Recall Cool Contrast Value Lumina nce Brightness Backlight Adjustment Recall Cool Brightness Value Focus Adjust Picture Phase to reduce Horizontal- Line noise Do ...
-
AOC 203P - page 13
H. Position Adjust the horizontal position of the OSD. 50 V. Position Adjust the verticalposition of the OSD. 50 OSD Setup OSD Timeout Adjust the OSD timeout. 10 English N/A Set OSD display language to English. Deutsch N/A Set OSD display language to German. Français N/A Set OSD display language to French. Español N/A Set OSD display language to ...
-
AOC 203P - page 14
PLUG AND PLAY Plug & Play DDC2B Feature This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host sy stem of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities. The DDC2B is a bidirectional data c hannel ...
-
AOC 203P - page 15
TECHNICAL SUPPORT (FAQ) Problem & Question Possible Solution Power LED is not on *Check if the Power Sw itch is in the ON position *Power Cord should be connected No Plug & Play *Check if the PC system is Plug & Play compatible *Check if the Video Card is Plug & Play compatible *Check if the D-15 plug pin of Video Cable is bent *Mak ...
-
AOC 203P - page 16
Screen image is not centered or sized properly. *Adjust pixel frequency (CLOCK) and FOCUS or press hot-key (AUTO). Picture has color defects (white does not look w hite) *Adjust RGB color or select color temperature. Horizontal or vertical disturbances on the screen *Use win 95/98 shut-dow n mode Adjust CLOCK and FOCUS or perform hot- key (AUTO-key ...
-
AOC 203P - page 17
ERROR MESSAGE & POSSIBLE SOLUTION CABLE NOT CONNECTED : 1. Check that the signal-cable is pr operly connected , If the connector is loose, tighten the connector’s screws. 2. Check the signal-cable’s connection pins for damage. INPUT NOT SUPPORTED : Your computer has been set to unsuitabl e display mode ,set the computer to display mode give ...
-
AOC 203P - page 18
APPENDIX SPECIFICATIONS Driving system TFT Color LCD LCD Panel Size 51cm(20") Pixel pitch 0.255mm( H )x 0.255mm( V ) Viewable angle 170 ° (H) 170 ° (V) R,G,B Analog Interface Video Digital interface H-Frequency 30KHz – 80Hz V-Frequency 55-75Hz Display Colors 16.7M Colors Dot Clock 162 MHz Max. Resolution 1600 x 1200 @ 60Hz Plug & Play ...
-
AOC 203P - page 19
Switch • Source • Auto Config / Exit • ∧ / Brightness • ∨ / Contrast • Menu / Enter • Power Button External Controls: Functions • Contrast • Brightness • Focus • Clock • H.Position • V.Position • (C1) Color • (C2)Color • SRGB Color temperature • User • Input signal Selection • OSD position, OSD timeout • La ...
-
AOC 203P - page 20
Preset Display Modes STANDA RD RESOLUTION HORIZONTA L FREQUENCY(KHZ) VERTICA L FREQUENCY(HZ) IBM DOS 720 × 400 31.47 70.0 640 × 480 31.47 60.0 VGA 640 × 480 37.50 75.0 800 × 600 37.879 60.0 SVGA 800 × 600 46.875 75.00 1024 × 768 48.363 60.0 1024 × 768 56.476 70.0 1024 x 768 60.02 75.0 1024 x 768 48.780 60.0 VESA XGA 1024 x 768 60.241 75.0 12 ...
-
AOC 203P - page 21
CONNECTOR PIN ASSIGNMENT 15 6 10 11 15 15 - Pin Color Display Signal Cable PIN NO. DESCRIPTION PI N NO. DESCRIPTION 1. Video-Red 9. +5V 2. Video-Green 10. Detect Cable 3. Video-Blue 11. NC 4. NC 12. DDC-Serial data ` Ground 13. H-sync 6. GND-R 14. V-sync 7. GND-G 15. DDC-Serial clock 8. GND-B 24 - Pin Color Display Signal Cable PIN NO. DESCRIPTION ...
-
AOC 203P - page 22
21 41G2001-615-1A 英文 ...
¿Tienes una pregunta acerca de AOC 203P?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con AOC 203P, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con AOC 203P probablemente compartirá una forma de solucionarlo.